Contamination of groundwater supplies by gasoline and other petroleum-derived hydrocarbons released from underground or aboveground storage tanks is a serious and widespread environmental problem. Corrosion, ground movement, and poor sealing can cause leaks in tanks and associated piping. Petroleum hydrocarbons contain methyl tertiary-butyl ether (MTBE) (a fuel oxygenate), benzene, toluene, ethylbenzene, and xylene isomers (BTEX), the major components of gasoline, which are hazardous substances regulated by many nations. MTBE possesses all the characteristics of a persistent compound in the subsurface: high solubility, low volatility, low sediment sorption, and resistance to biodegradation. The objectives of this study were to (1) evaluate the biodegradibility of MTBE under aerobic conditions, and (2) assess the potential of using the aerobic bioremediation technique to clean up aquifers contaminated by MTBE. In this study, microcosms were constructed to determine the feasibility of biodegrading MTBE by intrinsic microbial consortia (aquifer sediments) under aerobic and aerobic cometabolic conditions. In the cometabolic microcosms, propane, ethanol, and BTEX were applied as the primary substracts to enhance the biodegradation of MTBE. The inocula used in this microcosm study were aquifer sediments collected from the contaminated-zones of a petroleum-hydrocarbon (including MTBE) contaminated site. Microcosms were constructed with nutrient medium (or site groundwater), sediments, and MTBE solution in 70-mL serum bottles sealed with Teflon-lined rubber septa. MTBE was analyzed using purge-and-trap instrument following gas chromatography (GC)/flame ionization detector (FID). Results show that the indigenous microorganisms were able to biodegrade MTBE under aerobic conditions using MTBE as the sole primary substrate. Microcosms with site groundwater as the medium solution show higher MTBE biodegradation rate. This indicates that site groundwater might contain some trace minerals or organics, which could enhance the MTBE biodegradation rate. Results show that the addition of BTEX would also enhance the MTBE removal. However, no significant MTBE biodegradation was observed in microcosms with propane and ethanol as the primary substrates. This reveals that the supplement of the second carbon source might inhibit the degradation of MTBE due to the preferential removal of some organics over MTBE. Results from the microcosm study suggest that aerobic biodegradation plays an important role on the MTBE removal. Intrinsic bioremediation is a feasible technology to remediate the studied MTBE-contaminated site.

Contamination of soil/groundwater supplies by gasoline and other petroleum-derived hydrocarbons released from underground storage tanks (USTs) is a serious and widespread environmental problem. Corrosion, ground movement, and poor sealing can cause leaks in tanks and associated piping. Petroleum hydrocarbons contain methyl tertiary-butyl ether (MTBE) (a fuel oxygenate), benzene, toluene, ethylbenzene, and xylene isomers (BTEX), the major components of gasoline, which are hazardous substances regulated by many nations.The objective of this proposed study is to assess the potential of using a passive in situ oxidation barrier system. This passive active barrier system has advantages over conventional systems including less maintenance, cost-effectiveness, no above-ground facilities, no groundwater pumping and reinjection, and groundwater remediation in situ. The oxidation barrier system included a persulfate-releasing barrier, which contains persulfate-releasing materials. The slow-released persulfate would oxidize MTBE and benzene in aquifer. The persulfate-releasing materials would release persulfate when contacts with groundwater, thus oxidizes the MTBE and benzene. In the first part of this study, bench scale experiment was also performed to produce the persulfate-releasing materials high persulfate-releasing rate. The components of the persulfate-releasing materials and optimal concentrations of those components were determined in this study. Results indicate that the highest persulfate releasing rate can be obtained when the mass ratio of cement/sand/water was 1.4/0/0.7. Result obtained from the persulfate-releasing materials test and bench-scale were used for the design and operation of the following column experiments. Results from the column experiment indicate that approximately 98% of MTBE and 99% of benzene could be removed during the early persulfate-releasing stage. Results also reveal that the produced oxidation byproducts of MTBE, tert-butyl formate (TBF) and tert-butyl alcohol (TBA), can also be produce an acetone. Results from this study suggest that extra Fe(II) would cause the decrease in oxidation rates due to the reaction of sulfate with Fe(II). Results show that the parameters, which would affect the oxidation rate include persulfate concentration, oxidant reduction potential (ORP), conductivity, sulfate concentration, and contaminant concentration. The proposed treatment scheme would be expected to provide a more cost-effective alternative to remediate MTBE and other petroleum-hydrocarbon contaminated aquifers. Knowledge obtained from this study will aid in designing a persulfate oxidation system for site remediation.