The deposition of amorphous silica from aqueous solution on to rutile particles has been studied with the aim of elucidating the nature of the silica-titania interactions occurring and of following the progressive build up of the silica coating. The coating process, which involves the addition of an aqueous sodium silicate solution to an aqueous dispersion of titanium dioxide, has been investigated by performing a series of controlled preparations and using the technique of microelectrophoresis. Prepared silica-coated rutile samples ranging from partial to full silica coatings have been characterized using transmission electron microscopy, microelectrophoresis and nitrogen, argon and water sorption. Nitrogen and argon adsorption isotherms have been analysed using the equation of Brunauer, Emmett and Teller (BET). Differential energies of adsorption of nitrogen and argon have been determined calorimetrically. Water sorption isotherms have been analysed using the BET equation and the Frenkel - Halsey - Hill (FHH) equation. It has been shown that uniform silica coatings can be produced if adsorption of monomeric silica is followed by polymerization of silica at the solid/liquid interface. Surface cations on rutile may be hydroxylated or co-ordinately bound to water molecules and it appears that monomeric silica adsorbs preferentially by replacing ligand water molecules. Rutile particles with silica coatings thicker than approximately 2.5nm exhibit characteristics typical of silica and not of the base rutile. Silica coatings deposited at pH 10 contain narrow channels which are accessible to water molecules but not to nitrogen or argon. Neutralization to pH 7 reduces the volume in the coating accessible to water molecules.

<p>Abstract</p><p>The aim of the present study was to increase the understanding of how the cell surface properties affect the performance of unit operations used in primary protein purification. In particular, the purpose was to develop, set up and apply methods for studies of cell surface properties and cell interactions.</p><p>A method for microbial cell surface fingerprinting using surface plasmon resonance (SPR) is suggested. Four different <em>Escherichia coli </em>strains were used as model cells. Cell surface fingerprints were generated by registration of the interaction between the cells and four different surfaces, with different physical and chemical properties, when a cell suspension was flown over the surface. Significant differences in fingerprint pattern between some of the strains were observed. The physical properties of the cell surfaces were determined using microelectrophoresis, contact angle measurements and aqueous two-phase partitioning and were compared with the SPR fingerprints. The generated cell surface fingerprints and the physical property data were evaluated with multivariate data analysis that showed that the cells were separated into individual groups in a similar way using principal component analysis plots (PCA).</p><p>Studies of the behaviour of the model cells on stirred cell filtration and in an interaction test with different expanded bed adsorption (EBA) adsorbents were performed. It could be concluded that especially one of the strains behaved differently. Differences in the properties of the model cells were indicated by microelectrophoresis and aqueous two-phase partitioning which to some extent correlated with observed differences in behaviour during filtration and in an interaction test with EBA adsorbents.</p><p>The impact of high-pressure homogenisation of <em>E. coli </em>cell extract was examined, with a lab scale and a pilot scale technique. The DNA-fragmentation, visualised with agarose gel electrophoresis, and the resulting change in viscosity was analysed. A short homogenisation time resulted in increased viscosity of the process solution that correlated with increased concentration of released non-fragmented DNA. With longer homogenisation time the viscosity decreased with increasing degree of DNA-fragmentation.</p><p>The results show that strain dependant cell surface properties of<em> E. coli</em> may have an impact on several primary steps in downstream processing.</p>

Abstract The aim of the present study was to increase the understanding of how the cell surface properties affect the performance of unit operations used in primary protein purification. In particular, the purpose was to develop, set up and apply methods for studies of cell surface properties and cell interactions. A method for microbial cell surface fingerprinting using surface plasmon resonance (SPR) is suggested. Four different Escherichia coli strains were used as model cells. Cell surface fingerprints were generated by registration of the interaction between the cells and four different surfaces, with different physical and chemical properties, when a cell suspension was flown over the surface. Significant differences in fingerprint pattern between some of the strains were observed. The physical properties of the cell surfaces were determined using microelectrophoresis, contact angle measurements and aqueous two-phase partitioning and were compared with the SPR fingerprints. The generated cell surface fingerprints and the physical property data were evaluated with multivariate data analysis that showed that the cells were separated into individual groups in a similar way using principal component analysis plots (PCA). Studies of the behaviour of the model cells on stirred cell filtration and in an interaction test with different expanded bed adsorption (EBA) adsorbents were performed. It could be concluded that especially one of the strains behaved differently. Differences in the properties of the model cells were indicated by microelectrophoresis and aqueous two-phase partitioning which to some extent correlated with observed differences in behaviour during filtration and in an interaction test with EBA adsorbents. The impact of high-pressure homogenisation of E. coli cell extract was examined, with a lab scale and a pilot scale technique. The DNA-fragmentation, visualised with agarose gel electrophoresis, and the resulting change in viscosity was analysed. A short homogenisation time resulted in increased viscosity of the process solution that correlated with increased concentration of released non-fragmented DNA. With longer homogenisation time the viscosity decreased with increasing degree of DNA-fragmentation. The results show that strain dependant cell surface properties of E. coli may have an impact on several primary steps in downstream processing. / QC 20101129