Les conditions nécessaires pour obtenir des céramiques transparentes (absence de porosité, absence de seconde phase) requièrent une totale maitrise de chacune des étapes (synthèse, mise en forme, frittage) intervenant dans le processus, ce qui rend encore difficile l'industrialisation d'un procédé d'élaboration reproductible. Dans ce contexte, ce travail de thèse s’est focalisé à développer et évaluer la capacité du procédé de frittage micro-ondes à améliorer la robustesse du processus d'élaboration de spinelle transparent. La mise en place d'un dispositif de dilatométrie optique et une nouvelle technique de calibration originale, basée sur la fusion d'oxyde, ont permis de caractériser le frittage micro-ondes du spinelle pur avec une plus grande confiance. Même si aucun effet lié au procédé micro-onde n’a pu être mis en évidence pour le frittage du spinelle pur (trajectoire de frittage, mécanisme de densification et évolution de la porosité identiques), ces travaux ont démontré que l’impact de dopants pouvait être amplifié en présence du rayonnement micro-ondes. Ainsi, un décalage des courbes de retrait vers les basses températures a été observé lors du frittage micro-ondes du spinelle dopé avec TiO2 et MgO. L'existence d'un couplage particulier entre les défauts ponctuels chargés (lacunes, cations interstitiels) et le champ électrique pourrait être à l'origine de ce phénomène. Ces travaux de thèse ont également démontré la faisabilité de fritter des pièces de spinelle carrées de grandes dimensions (< 65 mm) compatibles avec un post-traitement HIP, en vue d'obtenir des pièces transparentes. Pour cela, un four micro-ondes monomode 915 MHz a été automatisé et une cellule de frittage adaptée a été développée. A l'issue du traitement HIP, les pièces ont présenté une transparence et des propriétés mécaniques (dureté; ténacité) comparables à celles des pièces pré frittées par voie conventionnelle. / The elaboration of transparent ceramics (no porosity, no second phase) requires a strict control of all steps of the process (synthesis, shaping, sintering). As a result, the industrialization of a reproducible process is still difficult to achieve. In this context, this thesis has focused on developing and evaluating the ability of the microwave sintering process to improve the robustness of the transparent spinel elaboration process.The set-up of an optical dilatometer and a new original calibration method, based of melting of different oxides, allowed to characterize the microwave sintering with a greater confidence. Even if no microwave effect has been observed on the sintering of pure spinel (identical sintering trajectory, densification mechanism and porosity evolution), this work has shown an amplification of the impact of dopants during microwave sintering. A shift of the shrinkage curves towards the low temperatures was observed during the microwave sintering of the spinel doped with TiO2 and MgO. The existence of a particular interaction between charged point defects (vacancies, interstitial cations) and the electric field could explain this phenomenon.This work thesis has shown also the feasibility of sintering of large square spinel pieces (< 65 mm) compatible with post treatment HIP in order to produce transparent ceramics. For this purpose, the microwave system working at 915 MHz was automatized and a new sintering configuration was developed. After a post-treatment, the transparency and mechanical properties (hardness; tenacity) of microwave pre-sintered samples were comparable with those of samples sintered by conventional heating.

Structure evolution of silica aerogel was studied in microwave- and conventionally processed samples over the temperature range from 25 to 1200â °C. The samples were produced using sol-gel processing and dried under carbon dioxide supercritical conditions. After drying, the monolithic samples received a thermal treatment at different programmed temperatures in two different ovens, conventional and microwave. The microwave process was performed using a single mode microwave oven at 2.45GHz. Dielectric properties were measured using the cavity perturbation method, and structural characterization was carried out using a variety of techniques, including absorption surface analysis, Helium pycnometry, Archimedes principle, Fourier transform infrared spectroscopy, X-ray diffraction, and high resolution microscopy. The data obtained revealed that structural differences do exist between microwave- and conventionally processed samples. Three different regions were identified from the structural characterization of the samples. Regions I exhibited a structure densification at temperatures between 25 and 850â °C. Region II was characterized by a bulk densification in the temperature range from 850 to 1200â °C. Region III was represented by the onset of crystallization above 1200â °C. Explanation and possible causes behind the structural differences observed in each region are provided. In general, the structure evolution observed in microwave- and conventionally processed samples followed the same order, but occurred at lower temperature for the microwave process. / Ph. D.