The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.

The growth of thermophiles during the manufacture of milk powder leads to a progressive increase in the number of thermophilic bacteria contaminating the final product. The limited residence time of the milk in the plant during milk powder manufacture and the concentration effect of converting milk into milk powder cannot explain the number of thermophiles found in the final product. This suggests that thermophiles are attaching to the large surface area of stainless steel found within a milk powder plant and then growing and developing into biofilms, with individual cells and/or biofilm fragments sloughing off into the product line and thus contaminating the final product. The aim of the present study was to investigate the attachment mechanisms that enable the thermophile Anoxybacillus flavithermus (B 1 2) to attach to stainless steel surfaces. Passing a B 1 2 culture through a column of stainless steel chips, collecting the first cells to pass through, re-culturing and repeating the process six times, resulted in the isolation of a mutant, labelled X7, with lO-fold reduced ability to attach to stainless steel as well as a reduced ability to attach to plastic and glass. A comparison of bacterial cell surface properties indicated that X7 was less hydrophobic than its parental strain B 1 2 . Cell surface charge measurements also suggest that X7 has less net negative surface charge. Disruption of extracellular polysaccharides and DNA appeared to have no effect on the attachment process. Removal of surface proteins caused a reduction in attachment of B 1 2 and X7 as well as a reduction in surface hydrophobicity suggesting surface protein involvement in both. Analysis by two-dimensional gel electrophoresis of lysozyme/mutanolysin extracted surface proteins revealed two proteins expressed at reduced levels in X 7 compared with B 1 2 . One protein was identified by mass spectrometry as the cytoplasmic enzyme Formate acetyltransferase. The role of Formate acetyltransferase and the second unidentified protein on the attachment process of Anoxybacillus flavithermus remains unclear.

The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.

The objective of this study was to investigate the effects of preheat treatments on fouling by fresh whole milk (FWM), recombined whole milk (RCB) and reconstituted whole milk (Recon) in the high-temperature heater of indirect UHT plants. Various preheat treatments prior to evaporation during milk powder manufacture were applied to skim milk powder (SMP, 75 °C 2 s, 85 °C, 155 s and 95 °C, 155 s) and whole milk powder (WMP, 95 °C, 33 s). These preheat treatments were so-called “evaporator preheat treatments”. Skim milk powder (SMP) and whole milk powder (WMP) were derived from the same original batch of pasteurised FWM to remove the effects of the variation in milk composition between different milk batches. These SMPs were recombined with anhydrous milk fat and water to prepare RCB, and WMPs were reconstituted with water to prepare Recon. Then, (homogenized) FWM, RCB and Recon were subjected to various preheat treatments (75 °C, 11 s, 85 °C, 147 s and 95 °C, 147 s) prior to UHT processing. These preheat treatments were so-called “UHT preheat treatments”. Temperature difference (hot water inlet temperature – milk outlet temperature) was taken as a measure of the extent of fouling in the high-temperature heater. The slope of the linear regression of temperature difference versus time (for two hours of UHT processing) was taken as fouling rate (°C/h). Increasing both evaporator and UHT preheat treatments resulted in increasing fouling rate and total deposit weight for all three whole milk types for several milk batches. In the case of FWM, there was no reduction in fouling rate with increasing UHT preheat treatment whether FWM was homogenized then preheated, preheated then homogenized or not homogenized at all. These findings, which are wholly consistent and well replicated, are in apparent conflict with the results of most previous comparable studies. Possible reasons for this are explained. Further investigations of the effects of homogenization relating to the role of whey protein on the surface of the fat globules showed that whey protein associated with the membrane covering the surface of fat globules for homogenized then preheated FWM, RCB and Recon and that association increased with increasing heating process stage. The increasing association of whey protein with the milk fat globules membrane with increasing severity of heating process stage became faster when preheat treatment was more severe: the association of whey protein plateaued on intermediate temperature heating when the milks were preheated at 75°C, 11 s and on preheating when the milks were preheated at 95°C, 147 s. In the case of FWM, the thickness of the membrane covering the surface of fat globules for homogenized then preheated FWM, which increased with the severity of heating process stage, was greater than the thickness of the membrane in preheated then homogenized FWM. Preheating then homogenization resulted in the greater interfacial spreading of small molecules on the surface of fat globules, i.e. whey protein or small molecules from the disintegration of casein micelles during preheating. Possible basic mechanisms for UHT fouling in the high-temperature heater include: the reduction in the solubility of calcium phosphate and the deposition of protein as fat-bound protein and non-fat-bound protein. When non-fat-bound protein in milk plasma deposited, it could be a carrier for the deposition of mineral, such as, the precipitate of calcium phosphate in the casein micelles or the deposition of complexes between whey protein and casein micelles.