Alginates are copolymers of &beta / -D-mannuronic (M) and &alpha / -L-guluronic acids (G). In this study, Azotobacter vinelandii ATCC&reg / 9046 was used to produce alginate in a fermentor. The effect of parameters such as dissolved oxygen tension (DOT), agitation speed, initial concentrations of sucrose and calcium on the properties of alginate were examined. Changes of DOT in the range of 1 and 10 % affected alginate production. The optimum DOT giving high alginate yield (4.51 g/L) and maximum viscosity was observed as 5 % yielding moderate GG-blocks of 55 %. Both high and low agitation levels reduced alginate production, but these conditions increased GG-block alginates as 76 and 87 % at 200 and 700 rpm, respectively. Moderate sucrose and calcium concentrations, 20 g/L and 50 mg/L, respectively were found better since further increase in their concentrations did not lead to a considerable improvement in alginate production and quality. Sodium alginates produced in this work were investigated for maximum heavy metal uptake with a special focus on copper ion and the highest copper uptake was around 1.9 mM Cu2+/g alginate. Findings showed that the block distribution of alginate was not as important as expected for copper removal. Alginate together with calcium ions was used for the removal of turbidity. The amount of GG-block was found to be important in turbidity removal. Alginate having 55 % GG block and 8.9 cP viscosity resulted in a final turbidity lower than 1 NTU at 2 mg/L of alginate with 60 mg/L of calcium ion.

This work addresses the distribution of N-methylolacrylamide (NMA) units in crosslinking poly(vinyl acetate) (PVAc) adhesives. In this case, distribution refers to the three potential locations of polymerized NMA units in a latex: the water-phase, the surface of polymer particles, and the core of the polymer particles. The objective is to identify the distribution of NMA in three latices and to determine whether NMA distribution correlates with durability related performance. NMA distribution was studied via a series of variable temperature solution NMR experiments, while the durability-related performance was studied via mode I fracture mechanics tests. Studying the distribution of NMA required the use of isotopically labeled NMA. Both 15N-NMA and 13C, 15N-NMA were synthesized. Three NMA/vinyl acetate (VAc) latices were prepared. The NMA feed strategy was varied during each of the three emulsion copolymerizations. Latex characterization methods including differential scanning calorimetry (DSC), rheometry, particle size analysis, and scanning electron microscopy (SEM) were used to study the three latices. The solution NMR method to identify NMA distribution was performed on untreated latices and on washed latices. Washing techniques included membrane dialysis and centrifugation. Results revealed that the three latices had different NMA distributions, and that the distributions were related to the expected differences in microstructure. Latex 3 had ~ 80% core-NMA, while Latex 2 had ~ 80% surface-NMA. Latex 1 had a high proportion of surface-NMA (~60%), but also had the highest proportion of water-phase NMA (~ 20%). This high proportion of water-phase NMA could be responsible for the unique morphology Latex 1 exhibited in SEM studies. Mode I opening fracture mechanics studies were used to study adhesive performance. Specimens were analyzed after exposure to accelerated aging treatments. Latex 2 and Latex 3 exhibited very similar results, despite having very different NMA distributions. All three latices showed good durability related performance. In Latex 2 and Latex 3, the critical strain energy release rates (Gc) after accelerated aging treatments were statistically the same as the Gc of the control specimens. The most interesting finding was that the Latex 1 Gc values were significantly higher after accelerated aging. Latex 1 also had the highest proportion of water-phase NMA. Bondline images and SEM micrographs both indicated that the integrity of Latex 1 was least affected by the accelerated aging treatments. / Ph. D.