1 |
Thermal Energy Storage Using Phase Change Materials in Corrugated Copper PanelsAigbotsua, Clifford Okhumeode 2011 May 1900 (has links)
Thermal energy storage systems, precisely latent thermal energy storage (LTES), are systems capable of recovering and storing thermal energy from waste processes, including hot exhaust gases out of combustion engines, or even renewable sources of energy like solar energy. LTES rely on phase change materials (PCMs) to store a significant amount of thermal energy in a relatively small volume. With limited volume and at almost constant temperature, they are capable of storing a large amount of thermal energy, mainly latent energy. Studies of LTES systems have focused primarily on system and process optimization including transient behavior as well as field performance. A major drawback in the development of the use of PCM in LTES has been the low thermal conductivity characteristic of most PCMs. Thus, there is a need to enhance heat transfer using reliable techniques, with the goal of reducing the charging and discharging times of PCM in LTES systems.
Some approaches that have been studied in the past include use of finned tubes, insertion of metal matrix into PCM, and microencapsulation of PCM. The performance of TES configurations in forced convection have been characterized using Reynolds numbers (Re), and Stefan numbers (Ste) of the heat transfer fluid (HTF) for different enhancement techniques. The goal of this study is to experimentally investigate the effectiveness of corrugated PCM panels with high surface-to-volume ratio in forced convection as a function of HTF mass flow rate, charging temperature, and flow direction through a corrugated TES unit. The PCM (octadecane) has been segmented using sealed corrugated panels containing several channels immersed in the HTF stream. With this approach, the author expects that the charging and discharging times will be substantially reduced due to the high surface-to-volume ratio of the PCM panel for heat transfer. Of the three conditions examined, the HTF direction influenced the charging and discharging times the most with significant reductions in these times observed when the HTF flow direction through the TES was upwards. Buoyancy effects, observed at high Stefan numbers, were important during the charging (melting) process and greatly influenced the temperature profiles along each channel. Results indicate that the devised TES is more effective than some other TES systems in the literature.
|
2 |
Characterization of Electrohydrodynamic (EHD) heat transfer enhancement mechanisms in melting of organic Phase Change Material (PCM)Nakhla, David January 2018 (has links)
The effect of using high voltage DC and AC on the heat transfer process during the melting of a Phase Change Material (PCM) in a rectangular enclosure was studied experimentally and numerically. The experiments were conducted for two configurations: (a) a horizontal rectangular enclosure in which the initial melting process is governed by heat conduction, (b) a vertical rectangular enclosure in which the initial melting process is governed by heat convection.
The level of heat transfer enhancement was quantified by using a novel experimental facility for the horizontal configuration. The experimental methodology was verified first against non-EHD melting cases and then was further expanded to include the EHD effects. The experiments showed that EHD forces can be used to enhance a conduction dominated melting up to a maximum of 8.6-fold locally and that the level of enhancement is directly related to the magnitude of the applied voltage. It was found that the main mechanism of enhancement in these cases can be attributed to the electrophoretic forces and that the role of the dielectrophoretic forces is minimal under the applied voltages.
In the vertical configuration, the effect of the magnitude of the applied voltage, the applied voltage wave-form, the gravitational Rayleigh number, Stefan number and the aspect ratio of the enclosure on the heat transfer enhancement were investigated experimentally. A novel shadowgraph experimental measurement system was developed and verified against the analytical correlations of natural convection in rectangular enclosures and the non-EHD melting performance was verified against the bench mark experiments of Ho (1984). The shadowgraph system was used to measure the local heat transfer coefficient across the heat source wall (the heat exchanger surface). The local heat transfer measurements along with the melting temporal profiles were used to explain and visualize the coupling between the Electrohydrodynamics (EHD) forces and the gravitational forces.
It was found that the EHD forces could still enhance the melting process even for an
initially convection dominated melting process. The mechanism of enhancement was found
to be a bifurcation of the initial convection cell into multiple electro-convective cells
between the rows of the electrodes. The shadowgraph system was used to assess the interaction between the electrical and the gravitational forces through the visualization of these cells and quantifying their size. The EHD heat transfer enhancement factor was found to increase by the increase of the applied voltage, reaching a 1.7 fold enhancement at the lower gravitational Rayleigh number tested and 1.45 fold for the highest gravitational Rayleigh and Stefan number. The effect of the polarity of the applied voltage was tested for the different cases and it was found that there was no significant difference between the positive and the negative polarities when the magnitude of the applied voltage was below 4 kV. At higher voltages- 6kV- the negative polarities showed better level of enhancement when compared to the positive applied voltage. It was again found that the main mechanism of enhancement is attributed to charge injection from the high voltage electrodes.
A scaling analysis was conducted based on the previous conclusions and the dominant mechanism of enhancement to describe the problem in non-dimensional form. An electrical Rayleigh number was introduced and its magnitude was correlated to the magnitude of the injected current. The melt volume fraction was then represented against the non-dimensional parameter (n+1)(H/W)Fo.Ste.RaE^0.25 and the melt fraction temporal profiles for the different voltages collapsed well against this parameter.
Finally, a numerical analysis was conducted on the role of the dielectrophoretic forces during the melting of Octadecane and when they would become of significant importance. The results of the numerical model supported the experimental findings and suggested that a minimum of 15 kV is needed in order to realize the effect of the dielectrophoretic forces. The numerical model was used to understand the interaction between the gravitational and the dielectrophoretic forces at different ranges of both gravitational Rayleigh number and electrical Rayleigh number. The model was complemented with scaling analysis to determine the governing scales of the problem and the dielectrophoretic Rayleigh number was deduced from the study. / Thesis / Doctor of Philosophy (PhD)
|
Page generated in 0.0455 seconds