No description available.

Template synthesis and mesostructural characterization of ordered mesoporous silica, titania and carbon materials have been systematically investigated in this study. In order to obtain a better understanding of the template-precursor relationship, there are two templates adopted in this research. One is the ¡§liquid crystal template (LCT)¡¨, composed of surfactants via self-assembly pathway; the other is the ¡§ordered silica spheres template¡¨, composed of monodispersed SiO2 spheres (~40 nm) via gravity sedimentation. This work was carried out in four related directions: (1) Synthesis and functionalization of ordered mesoporous silicate (MCM-41 and MCM-48) via cationic surfactant template; (2) Using anionic surfactant template-assisted via urea treatment to control the morphology of the TiO2; (3) Synthesis of ordered mesoporous anatase TiO2 via cationic surfactant template; (4) Synthesis of ordered mesoporous carbon from mesophase pitch solution via silica spheres template. Mesoporous silica materials MCM-41 and MCM-48 have been synthesized and identified. The MCM-41 has a hexagonal phase (p6m) with surface area of 1006.90 m2/g and pore size of 37.65 Å, The MCM-48 has cubic phase ( ) with surface area of 1093.34 m2/g and pore size of 29.20 Å. The calcined MCM-41was rehydrated by heating in water and functionalized with 3-amino propyltrimethoxysilane; this functionalized mesoporous silica is targeted as a template of metal oxides, such as TiO2. appears the same tendency of parent MCM-41 in the N2 sorption isotherm measurements. Nanocrystalline TiO2 rods and hollow-tubes with an engraved pattern on the surface have been prepared by the anionic template-assisted sol-gel synthesis via urea treatment and under hydrothermal condition. X-ray diffractometry (XRD) results indicate that these nanocrystallines consist predominantly of anatase TiO2, with minor amounts of rutile and brookite. The crystallographic facetting found from SEM and TEM further reveals the polymorphic nature of the nanocrystalline TiO2 thus prepared. A ¡§reverse micelle¡¨ formation mechanism taking into account the hydrothermal temperature, the pH effect of the sol-gel system, the isoelectric point, the formation of micelles, and the electrostatic interaction between the anionic surfactant and the growing TiO2 particulates is proposed to illustrate the competition between the physical micelle assembly of the ionic surfactants and the chemical hydrolysis and condensation reactions of the Ti precursors. Ordered mesoporous TiO2 materials with an anatase framework have been synthesized by using a cationic surfactant template and soluble peroxytitanates as Ti precursor through an S+I− self-assembly pathway. The low-angle X-ray diffraction (XRD) pattern of the as-prepared mesoporous TiO2 materials indicates a hexagonal mesostructure. XRD and TEM results and N2 sorption isotherms measurements indicate the calcined mesoporous TiO2 possesses an anatase crystalline framework having a maximum pore size of 6.9 nm and a maximum BET specific surface area of 284 m2/g. This ordered mesoporous TiO2 also demonstrates a high photocatalytic activity for degradation of methylene blue under ultraviolet irradiation. Under a lower carbonization temperature and with a mesophase pitch solution as the carbon precursor, ordered mesoporous carbon thick films with 35-nm pore size have been synthesized using SiO2 spheres as the template. The pore size of the mesoporous carbon thus fabricated was the smallest one ever reported using silica templates. SEM and TEM patterns show a discernible morphology of an ordered cubic close-packing of the mesopores interconnected via holes of 6 nm in diameter. From this study, the template synthesis has been proven to be an effective method to fabricate mesoporous silica, polymorphic titania, ordered mesoporous TiO2, and ordered mesoporous carbon materials. Further utilization of this template synthesis is expected to offer a variety of porous networks with a wide range of pore sizes, well-defined morphologies on controllable length scales, and various chemical functionalities to match the needs of different applications.

No description available.

There is an increasing demand for materials that are physically robust, easily recovered, and able to perform a wide variety of chemical functions. By combining hard and soft matter synergistically, organic-inorganic hybrid materials are potentially useful for a number of applications (e.g. catalysis, separations, sensing). In this respect, organic/ordered mesoporous silica (OMS) hybrids have attracted considerable attention, with an increasing emphasis on complex organic moieties achieved through multi-step reactions and polymerizations. It is on this front that we have focused our work, specifically in regard to polypeptides. Polypeptides are well suited organic components for hybrids as they provide a wide range of possible side chain chemistries (NH2, -SH, -COOH, -OH, etc.), chirality, and have conformations that are known to be responsive to external stimuli (pH, electrolytes, solvents, etc.). Our work has shown that N-carboxyanhydride chemistry offers a facile single step approach to the incorporation of dense polypeptide brushes in OMS. Modifying the initiator loading, pore size, pore topology, and monomer identity significantly impacted the properties of the obtained composites and peptide brush layers. Extending this work, a synthesis paradigm for preferentially grafting poly-L-lysine to the external and internal surfaces of SBA-15, a widely used OMS material, was developed. We observed that the pores of these hybrids could be opened and closed by the reversible swelling of the polypeptide layer. Similarly, novel bifunctional hybrids were synthesized by grafting polypeptides to the external surface of monodisperse OMS spheres that contain a thiol-functionalized core. The accessibility of the internal thiols to a fluorescent dye shows the potential of these hybrids for applications such as controlled uptake/release.

Highly ordered mesoporous carbon-silica nanocomposites with interpenetrating carbon and silica networks were synthesized by the evaporation-induced tri-constituent co- assembly approach. The removal of silica by concentrated NaOH solution produced mesoporous carbons, which contained not only the primary large pores, but also the secondary mesopores in the carbon walls. The thus synthesized mesoporous carbon was further activated by using ZnCl2. The activated mesoporous carbon showed an improved surface area and pore volume. The synthesized mesoporous carbon was tested for diuron removal from water and the results showed that the carbon gave a fast diuron adsorption kinetics and a high diuron removal capacity, which was attributable to the primary mesopore channels being the highway for mass transfer, which led to short diffusion path length and easy accessibility of the interpenetrated secondary mesopores. The optimal adsorption capacity of the porous carbon was determined to be 390 mg/g, the highest values ever reported for diuron adsorption on carbon-based materials.

Solubility-based membrane separation, in which the more soluble species preferentially permeates across the membrane, has attracted considerable recent attention due to both economic and environmental concerns. This solubility-selective mode is particularly attractive over a diffusivity-selective mode in applications in which the heavier species are present in dilute concentrations. Examples include the recovery of volatile organic components (VOCs) from effluent streams and the removal of higher hydrocarbons from natural gas. Recently, nanocomposites have shown great promise as possible membrane materials for solubility-selective separations. The chemical derivatization of inorganic mesoporous substrates has been explored to synthesize organic-inorganic nanocomposite membranes. The most exciting feature of this approach is that it enables the rational engineering of membrane nano-architecture with independent control over the free volume and chemistry to create membranes with highly customizable permselectivity properties. In this study, we synthesized the organic-inorganic nanocomposite membranes by decorating the surfaces of commercially available mesoporous alumina substrates, and surfactant-templated highly ordered mesoporous silicate thin films placed on commercially available macroporous inorganic substrates, with a selective organic material that is physically or chemically anchored to the porous surfaces. Hyperbranched melamine-based dendrimers, with nanometer dimension and chemical composition designed to target certain components, were used as filling agents. We evaluated these membranes for several environmentally relevant separations, such as the recovery of the higher hydrocarbon from air and the removal of trace VOCs from air or water, while exploring the impact of organic oligomer size, chemistry, and surface coverage, as well as substrate pore size and structure, on membrane performance. First, we did a model study to verify the feasibility of dendrimer growth inside mesopores by using ordered mesoporous silica. Alumina-ordered mesoporous silica (alumina-OMS) hybrid membranes were prepared as new inorganic porous substrates. Finally, we synthesized dendrimer-ceramic nanocomposite membranes by growing several generations of melamine-based dendrimers with diverse functional groups directly off the commercial alumina membranes. Composite membranes show very high propane/nitrogen selectivity up to 70.

Over the past few decades there has been great interest in exploring alternatives to conventional separation methods due to their high cost and energy requirements. Membranes offer a potentially attractive alternative as they potentially address both of these points. The overarching theme of this dissertation is to design nanocomposite membranes for processes where existing separation schemes are inadequate. This dissertation focuses on three challenges: 1) designing organic-inorganic hybrid membranes for reverse-selective removal of alkanes from light gases, 2) defect-free inorganic nanocomposite membranes that have uniform pores, and 3) nanocomposite membranes for minimizing protein fouling in microfiltration applications. Reverse-selective gas separations that preferentially permeate larger/heavier molecular species based on their greater solubility have attracted considerable recent attention due to both economic and environmental concerns. In this study, dendrimer-ceramic hybrid membranes showed exceptionally high propane/nitrogen selectivities. This result was ascribed to the presence of stable residual solvent that affects the solubility of hydrocarbon species. Mesoporous silica-ceramic nanocomposite membranes have been fabricated to provide defectless mesoporous membranes. As mesoporous silica is iteratively synthesized in the ceramic macropores, the coating method and the surfactant removal step significantly affected permeance and selectivity. It was also shown that support layers can cause a lower selectivity than Knudsen limit. Membrane fouling which results from deposition and nonspecific adsorption of proteins on the membrane surface is irreversible in nature, and results in a significant decrease in the membrane performance. To address this problem, two approaches were explored: 1) control of the surface chemistry tethering alumina membranes with organic components and 2) development of a novel photocatalytic membrane that exhibits hydrophilicity and can be easily regenerated. Both approaches can offer a viable route to the synthesis of attractive membranes, in that 1) the density of protein-resistant organic groups such as PEG is controllable by changing scaffolds or synthesis conditions and 2) the photocatalytic nanocomposite membranes can open the way for a new regeneration method that is environmentally benign.

Nanoporous materials have attracted tremendous interest, investment and effort in research and development due to their potential applications in various areas such as membranes, catalysis, sensors, delivery, and micro devices. Controlling a nanoporous material’s microstructure is of great interest due to the strong influence on efficiency and performance. For particles, microstructure refers to particle size, shape, surface morphology, and composition. When discussing thin films, microstructure includes film thickness, crystal orientation and grain boundaries. In this respect, we focus to develop novel methods for the synthesis and characterization of nanoporous materials and their films, which are capable of controlling the microstructure of material. This dissertation is composed of two main sections and each explores the fabrication of a different nanoporous material: 1) A simple fabrication method for producing oriented MFI zeolite membranes with controlled thickness, orientation, and grain boundary; 2) A microfluidic synthesis of ordered mesoporous silica particles with controllable size, shape, surface morphology, and composition. The first section of this dissertation demonstrates a simple and commercially viable method termed the micro-tiles-and-mortar method to make continuous b-oriented MFI membranes with controlled membrane microstructure. This simple method allows for control of the thickness of the membrane by using plate-like seed crystals with different thicknesses along the b-axis (0.5 μm to 2.0 μm), as well as to manipulate the density and structure of grain boundaries. Microstructural effects of silicalite-1 membranes on the gas separation are investigated by measuring the permeation and separation for xylene isomers. In the second section of this dissertation, a new synthesis method for the ordered mesoporous silica particles with controllable microstructure is demonstrated. This novel method combines a microfluidic emulsification technique and nonaqueous inorganic synthesis with a diffusion-induced self-assembly (DISA). The systematic control of the particle microstructure such as size, shape, and surface morphology is shown by adjusting microfluidic conditions.

No description available.

Ce travail est consacré à la préparation de matériaux mésoporeux à partir de cristaux liquides formés avec des tensioactifs fluorés selon le mécanisme transcriptif LCT. Les paramètres de synthèse ont été optimisés pour la préparation de silices mésostructurées à partir de la phase hexagonale du système eau/C8F17C2H4(OCH2CH2)9OH. Les résultats montrent une corrélation entre le diamètre des pores des matériaux et les diamètres hydrophobes mesurés dans les cristaux liquides. L'incorporation de TiO2 dans une matrice silicatée selon la méthode de coprécipitation a été réalisée en utilisant soit des micelles (mécanisme d'auto-assemblage coopératif CTM), soit la phase hexagonale du système C8F17C2H4(OCH2CH2)9OH/eau (mécanisme transcriptif LCT). Dans les deux cas, l'incorporation de titane conduit à une perte de la structure et à une diminution de la surface spécifique. L'utilisation du mécanisme CTM favorise la formation de TiO2 anatase en surface du matériau, tandis que pour le mécanisme LCT, la substitution du silicium par le titane au coeur du matériau a été mise en évidence. Des films minces mésostructurés à base de TiO2 ont été réalisés à partir de la méthode EISA. Les analyses par diffraction des rayons X à incidence rasante couplées à des mesures de réflectivité ont permis de mettre en évidence la structure des films et de déterminer les épaisseurs des couches qui constituent les films. Enfin, une méthode originale de synthèse de matériaux mésoporeux organisés à base de TiO2 a été développée. La précipitation de TiO2 dans la mésophase hybride est déclenchée à l'aide d'un traitement par NH3 (g). La structure des matériaux est conservée après l'étape de calcination laquelle permet de cristalliser TiO2 en phase anatase. L'activité photocatalytique de ces matériaux a ensuite été testée sur la réaction de photodégradation du méthylorange / This work deals with the preparation of mesoporous materials from fluorinated liquid crystals via the LCT mechanism. Synthesis parameters have been optimized for the preparation of ordered mesoporous silica with the hexagonal H1 phase of water/C8F17C2H4(OCH2CH2)9OH system. Results show a correlation between pore diameters of materials and hydrophobic diameters measured in liquid crystals. According to the coprecipitation method, incorporation of TiO2 in a silica matrix, synthesized using micelles (via the cooperative templating mechanism CTM) or the hexagonal phase of C8F17C2H4(OCH2CH2)9OH/water system (via liquid crystal templating mechanism LCT). Both pathways lead to a loss of mesopore ordering and a decrease of the specific surface area when titania content increases. If materials are prepared via CTM mechanism TiO2 is present on the surface whereas TiO2 is in the bulk when LCT mechanism is used. Mesoporous thin films have been prepared via EISA method. Grazing incidence small angle X-Ray scattering and reflectivity analysis have been used to define the structure of films and the thickness of the different layers. Finally an original method has been developed for the preparation of ordered titania mesoporous materials. Precipitation of titania in the hybrid mesophase is activated by a NH3 treatment. The structure is preserved after calcination step which allow the formation of TiO2 anatase. Photocatalytic activity of these materials has been tested on the photodegradation of methylorange