Spelling suggestions: "subject:"out off plant loading"" "subject:"out off plans loading""
1 |
Experimental Modeling and Laboratory Measurements of Drag Embedment Anchors Subjected to In-Plane and Out-Of-Plane LoadingDrake, Aaron C. 2011 August 1900 (has links)
Extreme hurricane events of the past decade are responsible for several drag embedment anchor (DEA) mooring failures of mobile offshore drilling platforms stationed within the Gulf of Mexico. A proposed failure mechanism is caused by out-of-plane loading. The current status of DEA holding capacity is based on empirical design charts and does not include the effects of out-of-plane loading. Experimental modeling using a 1:10 scale generic DEA was performed at the Haynes Coastal Engineering Laboratory at Texas A & M University to examine the effects of out-of-plane load conditions. Instrumentation and specialized devices were constructed to measure the anchor's trajectory through a representative sample of Gulf of Mexico clay with average un-drained shear strength of 0.764 kPa (16 psf). The sediment basin allowed for drag distances of 4.87 m (16 ft) and an embedment depth of 1.37 m (4.5 ft).
The measurements included pitch and roll of the anchor and line tension measured at the shank pad-eye. The variables modeled were fluke angle settings of 22°, 36° and 50°. The initial towline angle was varied from a minimum of 5° to upwards of 20°. Surface out-of-plane angles of 45° and 90° and embedment loading of 15°, 30° and 45° were examined. Curves of the ultimate holding capacity with respect to the out-of-plane towline angle and ultimate embedment depth were developed as functions of out-of-plane loading angles. Analysis of the rate effect indicates that a 46 percent increase in towing velocity causes an average 3 percent increase of holding capacity. The 50° fluke angle embeds an average of 0.7 fluke lengths deeper and has a holding capacity of 0.73 units greater than the 36° setting. The surface out-of-plane tests have a 5.1 percent reduction in holding capacity as the out-of-plane load angle increases from 45° to 90°. For all one fluke length initial towing distance tests, the ultimate holding capacity increases and the ultimate embedment depth decreases as the out-of-plane towing angle increases from 15° to 45°. The three fluke length initial towing distance tests indicate a contrasting trend, in that as the out-of-plane tow angle increases, both the ultimate holding capacity and ultimate embedment depth decrease.
|
2 |
Experimental modeling for in-plane and out-of-plane loading of scaled model drag embedment anchorsKroncke, Mark William 03 September 2009 (has links)
The failed anchoring systems of mobile offshore drilling units from hurricanes occurring in 2004 and 2005 established a need to better understand the ultimate pullout capacity and trajectory of scaled model anchors under typical and out-of-plane loading conditions. The six degrees of freedom of small scale drag embedment anchors were
studied in a laboratory testing environment with the intent that reasonable trends in anchor behavior will be found. Investigations within this experimental research program demonstrated the in-plane and out-of-plane loading behavior of conventional and prototype scaled model anchors embedded to predetermined depths in two different test beds of kaolinite clay with undrained shear strength profiles constant and increasing with depth. The anchors were loaded to failure in concentric, normal,
concentric, shear, eccentric, normal, eccentric, shear, inclined, and drag embedment loading configurations. This series of pullout and drag embedment tests provided a suite of test results indicating behavioral trends of the varying holding capacities and anchor trajectories. Results were compared with similar research presented in the literature and an analytical model predicting out-of-plane loading behavior of
similar anchors.
It was concluded that increasing eccentricities from both concentric, normal and concentric, shear loading configurations resulted in decreasing bearing capacity factors, confirming the predicted trend from the analytical model for these loading configurations. Trajectories observed for the concentric, normal, concentric, shear,
and eccentric, shear loading configurations showed that the anchors tracked straight out of the soil without deviation, but eccentric, normal loading found the anchor tending to track away from the initial loading location. For inclined loads, both anchors to track to whichever direction the anchor faced upon loading. Drag embedment trajectory was found to vary depending on the anchor, as the conventional anchor dove with an applied load and the prototype anchor rose towards the surface. / text
|
3 |
EVALUATION OF RESIDUAL STRENGTH OF CORRODED STRUCTURAL STEEL PLATES AND STIFFENED PANELSBajaj, Srikanth January 2018 (has links)
No description available.
|
4 |
Finite Element Analysis of Unreinforced Concrete Block Walls Subject to Out-of-Plane LoadingHe, Zhong 12 1900 (has links)
<p>Finite element modeling of the structural response of hollow concrete block walls subject to out-of-plane loading has become more common given the availability of computers and general-purpose finite element software packages. In order to develop appropriate models of full-scale walls with and without openings, a parametric study was conducted on simple wall elements to assess different modeling techniques. Two approaches were employed in the study, homogeneous models and heterogeneous models. The linear elastic analysis was carried out to quantify the effects of the modeling techniques for hollow blocks on the structural response of the assembly, specifically for out-of-plane bending. Three structural elements with varying span/thickness ratios were considered, a horizontal spanning strip, a vertical spanning strip and a rectangular wall panel supported on four edges. The values computed using homogeneous and heterogeneous finite element models were found to differ significantly depending on the configuration and span/thickness ratio of the wall.</p><p>Further study was carried out through discrete modeling approach to generate a three-dimensional heterogeneous model to investigate nonlinear behaviour of full-scale walls under out-of-plane loading. The Composite Interface Model, established based on multi-surface plasticity, which is capable of describing both tension and shear failure mechanisms, has been incorporated into the analysis to capture adequately the inelastic behaviour of unit-mortar interface.An effective solution procedure was achieved by implementing the Newton-Raphson method, constrained with the arc-length control method and enhanced by line search algorithm. The proposed model was evaluated using experimental results for ten full-size walls reported in the literature. The comparative analysis has indicated very good agreement between the numerical and experimental results in predicting the cracking and ultimate load values as well as the corresponding crack pattern. / Thesis / Master of Applied Science (MASc)
|
Page generated in 0.1301 seconds