Global ETD Search

1	Protective colloids : understanding nucleation and grafting Hunt, Paul Edward January 2012 (has links) Alkali-soluble resins (ASRs) were prepared by (i) solution and (ii) emulsion polymerization. All ASRs were synthesized with number-average molar masses < 20,000 g mol-1 and all had 15 wt% methacrylic acid 5 wt% styrene, the remaining 80 wt% was composed of either methyl methacrylate or a combination of methyl methacrylate and ethyl acrylate. All emulsion ASRs were made to 20% solids, with volume-average particle diameters (dv) in the region 30 – 50 nm, with a glass transition temperature of 80 – 120 °C. Emulsion polymerization was the preferred route for ASR synthesis, to allow further studies on their dissolution behaviour. Before their use as colloidal stabilizers, the dissolution behaviour of the ASRs needed to beinvestigated e.g. effect of temperature, molar mass, and composition. Particle size and absorbance measurements were taken during dissolution of ASRs to achieve 100%neutralization and these were shown to have two stages, an apparent particle swelling (whichwas rapid), and a slower, decrease in particle size as water-soluble polymeric material wasdiffusing out of the ASR particles. From this, further interpretation allowed for calculating the diffusion coefficient of the ASR polymer using the Stokes-Einstein equation. Time-domain nuclear magnetic resonance (TD-NMR) was employed to enhance understanding of what is occurring in the ASR particles, and in the aqueous, continuous phase. The final aspect of this project was to use the ASRs prepared as colloidal stabilizers in emulsion polymerizations of butyl acrylate (BA) and butyl methacrylate (BMA) using varying levels and also the effect of adding additional surfactant. The results show that the effect of ASR molar mass, the concentration of stabilizer, and also the impact of the EA-containing ASR greatly influence stability, whereby lower ASR molar mass, higher levels of stabilizer and including EA greatly benefit colloidal stability in PBA latexes. In PBMA latexes, a similar trend was also observed, but, the presence of ethyl acrylate (EA) in the ASR backbone has a detrimental effect on the colloidal stability, caused by the inability of grafting to occur between the ASR and PBMA. 668.9
2	Raman and Infrared Imaging of Dynamic Polymer Systems Bobiak, John Peter January 2006 (has links) No description available. spectroscopic imaging Raman imaging Raman mapping FTIR imaging Infrared imaging Polymer dissolution Drug diffusion Single-walled carbon nanotubes
3	SHEAR RHEOMETRY PROTOCOLS TO ADVANCE THE DEVELOPMENT OF MICROSTRUCTURED FLUIDS Eduard Andres Caicedo Casso (6620462) 15 May 2019 (has links) <p></p><p>This doctoral dissertation takes the reader through a journey where applied shear rheology and flow-velocimetry are used to understand the mesoscopic factors that control the flow behavior of three microstructured fluids. Three individual protocols that measure relative physical and mechanical properties of the flow are developed. Each protocol aims to advance the particular transformation of novel soft materials into a commercial product converging in the demonstration of the real the chemical, physical and thermodynamical factors that could potentially drive their successful transformation. </p> <p> </p> <p>First, this dissertation introduces the use of rotational and oscillatory shear rheometry to quantify the solvent evaporation effect on the flow behavior of polymer solutions used to fabricate isoporous asymmetric membranes. Three different A-B-C triblock copolymer were evaluated: polyisoprene-<i>b</i>-polystyrene-<i>b</i>-poly(4-vinylpyridine) (ISV); polyisoprene-<i>b</i>-polystyrene-<i>b</i>-poly(<i>N</i>,<i>N</i>-dimethylacrylamide) (ISD); and polyisoprene-<i>b</i>-polystyrene-<i>b</i>-poly(<i>tert</i>-butyl methacrylate) (ISB). The resulting evaporation-induced microstructure showed a solution viscosity and film viscoelasticity strongly dependent on the chemical structure of the triblock copolymer molecules. </p> <p> </p> <p>Furthermore, basic shear rheometry, flow birefringence, and advanced flow-velocimetry are used to deconvolute the flow-microstructure relationships of concentrated surfactant solutions. Sodium laureth sulfate in water (SLE<sub>1</sub>S) was used to replicate spherical, worm-like, and hexagonally packed micelles and lamellar structures. Interesting findings demonstrated that regular features of flow curves, such as power-law shear thinning behavior, resulted from a wide variety of experimental artifacts that appeared when measuring microstructured fluids with shear rheometry.</p> <p> </p> <p>Finally, the successful integration of shear rheometry to calculate essential parameters to be used in a cost-effective visualization technique (still in development) used to calculate the dissolution time of polymers is addressed. The use of oscillatory rheometry successfully quantify the viscoelastic response of polyvinyl alcohol (PVA) solutions and identify formulations changes such as additive addition. The flow behavior of PVA solutions was correlated to dissolution behavior proving that the developed protocol has a high potential as a first screening tool.</p><br><p></p> Rheology Polymers and Plastics Applied Rheology shear rheometry self-assembly block copolymers Water-soluble polymers concentrated surfactants flow-visualization Ultrasonic speckle velocimetry simple-shear flow-instabilities wall-slip plug-flow Flow-Birefringence polymer dissolution polymer swelling shear-induced microstructures SNIPS polymer solutions triblock terpolymers PVA SLE1S bulky side groups spherical micelles worm-like micelles hexagonal phase Lamellar phase poly vinyl alcohol ISV ISD ISB Complex fluids microstructured fluids Flow Behaviors

1

Page generated in 0.0969 seconds