The heterogeneous and anisotropic nature of wood material creates additional design challenges not present with the use of other structural materials such as steel and aluminum. The natural variation in the physical properties of wood members requires that the specified strengths and resistances used for design calculations be based on the quantities measured for the fifth percentile of all wood materials tested. The result is that design may be unnecessarily conservative and subsequently inefficient. The same properties that cause uncertainty surrounding the physical properties of biological materials also create difficulty in applying non-destructive evaluation techniques. Strain measurement is one particular technique that is extremely valuable for materials of known and consistent stress-strain relationships, but whose usefulness is diminished when applied to biological materials. To demonstrate the need for more accurate strain measurement in light-framed structures, the predictive calculations and structural modelling of a post-framed building was compared to its demonstrated performance. The analysis did not adequately reflect the actual performance of the building, and it was determined that additional monitoring of light-framed buildings through systems such as strain measurement was required to gain a better understanding of the performance characteristics in order to optimize evaluation techniques. This project aimed to develop a system that accurately measures strain in dimensional lumber of different types, which in turn will enable researchers to enhance monitoring the performance of light-frame structures and optimize design analysis and structural modelling techniques. The development of a methodology that provides a practical means by which to perform in-situ testing of post-frame buildings and decreases the complexity of post-frame building monitoring will contribute to the advancement of design and analysis techniques. In the calibration phase of the project, metal foil resistance strain gages were mounted onto wooden specimens with dimensions of 5 x 13 x 40 mm, 5 x 40 x 100 mm, and 2 x 20 x 50 mm, and acrylic specimens with dimensions of 3 x 25 x 75 mm. These specimens were then subjected to loading in an ATS universal testing machine in the Physical Properties Lab at the University of Manitoba. Stress-strain curves were developed based upon the observed stress and strain levels. These calibrated gages were then mounted on to a 38 x 89 mm specimen of S-P-F dimensional lumber which represented a typical light-framed building material. This assembly was then subjected to a similar loading procedure as the calibrated gage and stress-strain curves were generated once again. The slopes of the stress-strain curves developed from the two phases of the project were compared to determine if a consistent correlation existed. The three sizes of wood specimens did not demonstrate a consistent correlation. However, the acrylic specimen demonstrated consistent correlation amongst two groups of three with correlation coefficients within a forty percent range in one group and within a nine percent range in the other group. This suggests that further experimental refinements could produce the desired results. / October 2007

The heterogeneous and anisotropic nature of wood material creates additional design challenges not present with the use of other structural materials such as steel and aluminum. The natural variation in the physical properties of wood members requires that the specified strengths and resistances used for design calculations be based on the quantities measured for the fifth percentile of all wood materials tested. The result is that design may be unnecessarily conservative and subsequently inefficient. The same properties that cause uncertainty surrounding the physical properties of biological materials also create difficulty in applying non-destructive evaluation techniques. Strain measurement is one particular technique that is extremely valuable for materials of known and consistent stress-strain relationships, but whose usefulness is diminished when applied to biological materials. To demonstrate the need for more accurate strain measurement in light-framed structures, the predictive calculations and structural modelling of a post-framed building was compared to its demonstrated performance. The analysis did not adequately reflect the actual performance of the building, and it was determined that additional monitoring of light-framed buildings through systems such as strain measurement was required to gain a better understanding of the performance characteristics in order to optimize evaluation techniques. This project aimed to develop a system that accurately measures strain in dimensional lumber of different types, which in turn will enable researchers to enhance monitoring the performance of light-frame structures and optimize design analysis and structural modelling techniques. The development of a methodology that provides a practical means by which to perform in-situ testing of post-frame buildings and decreases the complexity of post-frame building monitoring will contribute to the advancement of design and analysis techniques. In the calibration phase of the project, metal foil resistance strain gages were mounted onto wooden specimens with dimensions of 5 x 13 x 40 mm, 5 x 40 x 100 mm, and 2 x 20 x 50 mm, and acrylic specimens with dimensions of 3 x 25 x 75 mm. These specimens were then subjected to loading in an ATS universal testing machine in the Physical Properties Lab at the University of Manitoba. Stress-strain curves were developed based upon the observed stress and strain levels. These calibrated gages were then mounted on to a 38 x 89 mm specimen of S-P-F dimensional lumber which represented a typical light-framed building material. This assembly was then subjected to a similar loading procedure as the calibrated gage and stress-strain curves were generated once again. The slopes of the stress-strain curves developed from the two phases of the project were compared to determine if a consistent correlation existed. The three sizes of wood specimens did not demonstrate a consistent correlation. However, the acrylic specimen demonstrated consistent correlation amongst two groups of three with correlation coefficients within a forty percent range in one group and within a nine percent range in the other group. This suggests that further experimental refinements could produce the desired results.

The heterogeneous and anisotropic nature of wood material creates additional design challenges not present with the use of other structural materials such as steel and aluminum. The natural variation in the physical properties of wood members requires that the specified strengths and resistances used for design calculations be based on the quantities measured for the fifth percentile of all wood materials tested. The result is that design may be unnecessarily conservative and subsequently inefficient. The same properties that cause uncertainty surrounding the physical properties of biological materials also create difficulty in applying non-destructive evaluation techniques. Strain measurement is one particular technique that is extremely valuable for materials of known and consistent stress-strain relationships, but whose usefulness is diminished when applied to biological materials. To demonstrate the need for more accurate strain measurement in light-framed structures, the predictive calculations and structural modelling of a post-framed building was compared to its demonstrated performance. The analysis did not adequately reflect the actual performance of the building, and it was determined that additional monitoring of light-framed buildings through systems such as strain measurement was required to gain a better understanding of the performance characteristics in order to optimize evaluation techniques. This project aimed to develop a system that accurately measures strain in dimensional lumber of different types, which in turn will enable researchers to enhance monitoring the performance of light-frame structures and optimize design analysis and structural modelling techniques. The development of a methodology that provides a practical means by which to perform in-situ testing of post-frame buildings and decreases the complexity of post-frame building monitoring will contribute to the advancement of design and analysis techniques. In the calibration phase of the project, metal foil resistance strain gages were mounted onto wooden specimens with dimensions of 5 x 13 x 40 mm, 5 x 40 x 100 mm, and 2 x 20 x 50 mm, and acrylic specimens with dimensions of 3 x 25 x 75 mm. These specimens were then subjected to loading in an ATS universal testing machine in the Physical Properties Lab at the University of Manitoba. Stress-strain curves were developed based upon the observed stress and strain levels. These calibrated gages were then mounted on to a 38 x 89 mm specimen of S-P-F dimensional lumber which represented a typical light-framed building material. This assembly was then subjected to a similar loading procedure as the calibrated gage and stress-strain curves were generated once again. The slopes of the stress-strain curves developed from the two phases of the project were compared to determine if a consistent correlation existed. The three sizes of wood specimens did not demonstrate a consistent correlation. However, the acrylic specimen demonstrated consistent correlation amongst two groups of three with correlation coefficients within a forty percent range in one group and within a nine percent range in the other group. This suggests that further experimental refinements could produce the desired results.