141 |
Dynamic strain ageing and the fatigue behaviour of nimonic 901Venables, R. January 1986 (has links)
No description available.
|
142 |
Salt effects in nonionic surfactant/dodecane/water systemsFurlong, P. J. J. January 1989 (has links)
No description available.
|
143 |
Thermal measurements in heliumBatey, G. J. January 1987 (has links)
No description available.
|
144 |
Magnetism and excitations in praseodymium compoundsGardiner, Carol January 2003 (has links)
No description available.
|
145 |
Low temperature properties of amorphous solidsPage, J. N. January 1987 (has links)
No description available.
|
146 |
Magnetic and electronic properties of some low-dimensional compoundsBannister, D. J. January 1987 (has links)
No description available.
|
147 |
Laser spectroscopy of rare earth compoundsLazzouni, M. January 1988 (has links)
No description available.
|
148 |
Treatment of Phenol in Water Using Microwave-assisted Advanced Oxidation Processes2014 April 1900 (has links)
Phenol and its compounds are highly toxic even in low concentration, and have become the subject of intense research during the last two decades. Effluents from industries such as oil refining, paper milling, olive oil extraction, wood processing, coal gasification and textiles and resin manufacturing and agro-industrial wastes discharge phenols at levels much higher than the toxic levels set for this compound. Advanced Oxidation Processes (AOPs) such as UV, UV-TiO2, UV-H2O2, O3 and UV-O3 have become popular in recent years as efficient treatment methods for recalcitrant compounds like phenol.
The effect of microwave (MW) and combined MW-UV treatment on degradation of phenol was studied in aqueous solution in the presence and absence of TiO2 under controlled temperature conditions. It was found that the efficiency of MW and MW-UV processes for the degradation of phenol was less than 10% after 120 minutes of treatment. However, the efficiencies of MW-TiO2 (hydrothermal) and MW-TiO2 (sol-gel) were slightly more than those of the above processes at 12 to 15% after 120 minutes, which might be due to adsorption of the phenol on the surface of TiO2 particles. It also was observed that MW-UV-TiO2 was superior to any other process studied for the degradation of phenol. At natural pH, the degradation efficiency of MW-UV-TiO2 (HT) on 1500 ppm of phenol in water was 23%, and for MW-UV-TiO2 (SG) it was 20%. Hence, it can be concluded that the catalyst (TiO2) prepared by the hydrothermal (HT) method had better catalytic activity than TiO2 prepared by the sol-gel (SG) method, which might be due to its structural and optical characteristics. Of the two developed reactors which are MW and a combined MW-UV reactor, MW-UV combined with TiO2 could be used for most successful degradation of phenol.
|
149 |
Topographic, ultrasonic and diffraction studies of helical antiferromagnetsPatterson, C. J. F. January 1986 (has links)
No description available.
|
150 |
Influence of strain rate on oxide fractureMahmood, K. January 1988 (has links)
The ability of metals and alloys to form and retain protective oxide scales is crucial to their stability at elevated temperatures for extended times. Hence the identification of factors that promote or limit the integrity of oxides on high temperature materials has been the subject of intensive investigations. In the present study the mechanical properties of this chromium-rich scale on 304 stainless steel foil has been investigated in relation to the deformation rates in the substrate. It was shown that heavy cold working (up to 90%) delays the onset of breakaway oxidation and results in a very adherent scale. The cracking behaviour of the scale was found to be strain rate and temperature dependent under slow strain rate conditions when the substrate deforms by creep. No strain rate dependence was observed over the temperature range 700-900°C when faster strain rates (> 10⁻⁵ sec⁻¹) were applied. The transition between these two responses was found to vary only slightly with temperature between 5.0x10⁻⁵ sec⁻¹ and 7.8x10⁻⁵ sec⁻¹, increasing as the temperature is raised. A new method has been described for determining the fracture behaviour of oxide scale by estimating the composite defect size. From a knowledge of the onset of scale cracking, determined in situ using the acoustic emission technique, it was possible to correlate the measured intercrack spacing with the fracture toughness from which the tensile properties of the scale can be evaluated.
|
Page generated in 0.0752 seconds