The flow pattern has widely been recognized to have an impact on the exogenous non-metallic inclusion generation in the gating system and mold flux entrapment in the uphill teeming process. Thus, a well-controlled flow pattern during the teeming process can improve the quality of ingots and further increase the yield during steel production. The current study focused on investigating and optimizing the flow pattern of steel in the gating system and molds to improve steel cleanliness during the initial filling moment. A mathematical model considering a trumpet was initially compared to a reduced model only considering part of the runner channel. Thereafter, the influence of swirl blades implemented at the bottom of the vertical runner on the improvement of initial filling conditions in the molds was investigated in a model considering the entire mold system including a trumpet. The effects of a swirl blade orientation on a swirling flow were further discussed. The simulation results, when utilizing swirl blades, were also verified by plant trials performed at Scana Steel. In addition, a new novel swirling flow generation component, TurboSwirl, was studied in a model considering the entire mold system including a trumpet. The model was based on modifications of the refractory geometry at the elbow of the runners near the mold without the usage of an inserted flow control device in the gating system. Owing to its great potential for improving the flow pattern of steel during the initial filling moment, the effect of TurboSwirl on steel cleanliness was also studied. The results showed that the initial filling conditions during the uphill teeming process can be improved by using a swirl blade or a TurboSwirl in the gating system. This makes it possible to further decrease the initial position of mold powder bags. In addition, it reduces the possibilities of exogenous non-metallic inclusion generation in the gating system as well as mold flux entrapment in the mold during the uphill teeming process. However, the utilization of swirl blades created a considerable amount of droplets when steel entered the molds during the first couple of seconds, which also was verified by the plant trials. The introduction of TurboSwirl showed a greater potential than a swirl blade due to a more evenly distributed swirling flow. The DPM model adopted in the simulations revealed that the TurboSwirl can improve steel cleanliness by increasing the non-metallic inclusion collision rate both with respect to Stokes and turbulent collisions. / <p>QC 20130204</p>

The flow pattern in the uphill teeming process has been found to be closely related to the quality of ingots and further to affect the yield of ingot production, which is crucial for the steel making process. The formation of non-metallic inclusion and entrapment of mold flux has been considered to be affected by the flow pattern in the gating system and molds by many previous researchers. The aim of this study is to investigate the flow pattern of steel in the gating system and molds during the initial filling stage. In addition, to study the utilization of swirl blade implemented at the bottom of the vertical runner on the improvement of initial filling condition in the mold. A three dimensional model of two molds gating system for 6.2 ton ingots from Scana Steel was adopted in the present work. A reduced geometry model including one mold and a runner, based on the method from previous researchers, was also used for comparison with the current more extensive model. Moreover, a reduced geometry model including one swirl blade and a runner was simulated to find effects of an increased-length vertical runner on the flow pattern improvement at the vertical runner outlet. Flow pattern, hump height and wall shear stress were respectively studied. A reduced geometry with homogenous inlet conditions fails to describe the fluctuating conditions present as the steel enters the mold. However, the trends are very similar when comparing the (hump height-surface height) evolution over time. The implementation of swirl blades gives a chaotic initial filling condition with a considerable amount of droplets being created when steel enters the molds during the first couple of seconds. However, a more calm filling condition with less fluctuation is achieved at the molds after a short while. Moreover, the orientation of the swirl blades affects he flow pattern of the steel. A proper placement of a swirl blade improves the initial filling conditions. The utilization of swirl blades might initially result in larger hump height. However, it gives fewer fluctuations as the casting proceeds. In the model without swirl blades, the maximum wall shear stress fluctuates with a descending trend as the filling proceeds. An implementation of swirl blades can decrease and stabilize the wall shear stress in the gating system. A special attention should be made in choosing refractory at the center stone, the horizontal runner near center stone and the vertical runner at the elbow. This is where the wall shear stress values are highest or where the exposure times are long. / QC 20120203