Thesis (Ph. D.)--Virginia Polytechnic Institute and State University, 1992. / Vita. Abstract. Includes bibliographical references (leaves 240-251). Also available via the Internet.

Graduate

This thesis first describes the reverse method of transformer design. An existing magnetic model for full-core shell-type transformers, based on circuit theory, is summarised. A magneto-static finite element model is introduced and two sample transformers are analysed. The magnetic model based on finite element analysis is shown to be more accurate than the model based on circuit theory. Partial-core resonant transformers are then introduced and their characteristics are explained using an equivalent circuit model. A method of measuring the winding inductances under resonant operation is developed and used to investigate the characteristics of two different tuning methods. A finite element model of the partial-core resonant transformer is developed by adopting the model for full-core shell-type transformers. The model results accurately match the measured inductance variation characteristics of three sample transformers and predict the onset of core saturation in both axial-offset and centre-gap arrangements. A new design of partial-core resonant transformer is arrived at, having an alternative core and winding layout, as well as multiple winding taps. The finite element model is extended to accommodate the new design and a framework of analysis tools is developed. A general design methodology for partial-core resonant transformers with fixed inductance is developed. A multiple design method is applied to obtain an optimal design for a given set of specifications and restrictions. The design methodology is then extended to devices with variable inductance. Three design examples of partial-core resonant transformers with variable inductance are presented. In the first two design examples, existing devices are replaced. The new transformer designs are significantly lighter and the saturation effects are removed. The third design example is a kitset for high-voltage testing, with the capability to test any hydro-generator stator in New Zealand. The kitset is built and tested in the laboratory, demonstrating design capability. Other significant test results, for which no models have yet been developed, are also presented. Heating effects in the core are reduced by adopting an alternative core construction method, where the laminations are stacked radially, rather than in the usual parallel direction. The new kitset is yet to be used in the field.

Thesis (M.S.)--California Polytechnic State University, 2009. / Title from PDF title page; viewed on July 2, 2009. "June 2009." "In partial fulfillment of the requirements for the degree [of] Master of Science in Electrical Engineering." "Presented to the faculty of California Polytechnic State University, San Luis Obispo." Major professor: Taufik, Ph.D. Includes bibliographical references (p. 97-98).

High performance ac-to-dc converters are required to meet the regulation standards to suit wide variety of applications. This thesis presents the steady state analysis, design and operation of high frequency (HF) transformer isolated resonant converters on the single phase utility line as a low harmonic controlled rectifier. Two resonant converter configurations of third order have been studied namely the LCC-type parallel resonant converter also popularly known as series-parallel resonant converter (SPRC) and the hybrid parallel-series resonant converter bridge (HPSRCB). These converters are operated at HF using variable frequency as well as fixed frequency control and they operate in different modes depending on the choice of switching frequency and load. The variable frequency SPRC is operated in discontinuous current mode (DCM), to obtain low line current total harmonic distortion (T.H.D.) and high power factor (pf), without using active control. State space analysis has been presented for one of the predominant circuit modes encountered during its operation in DCM. The various design constraints for operating the resonant converter on the utility line for high pf operation have been stated for different control schemes. In addition, steady state analysis, design optimization carried out for dc-dc converter have been presented. The effect of resonant capacitor ratio on the converter performance characteristics have been studied. SPICE3 simulations and experimental results obtained from a 150 W converter are presented to verify the theory. Continuous current mode (CCM) operation of the SPRC, and its effect on the line current T.H.D. and pf are studied. Both fixed and variable frequency control schemes have been used to control the SPRC. Complex ac circuit analysis method has been considered as the design tool to get the design curves and design of the SPRC operating on the utility line. SPICE3 simulation results for open loop operation and experimental results for both open as well as closed loop operations (active control), for two capacitance ratio's have been presented to verify the converter performance. It is shown that nearly sinusoidal line current operation at unity pf can be obtained with closed loop operation. A HPSRCB has been proposed and operated at very high pf on the utility line as a controlled rectifier. Some of the predominant operating modes of the fixed and variable frequency HPSRCB have been identified. The steady state analysis using state space modeling presented for a dc-to-dc converter has been extended to analyze the ac-to-dc converter. Using the large signal discrete time domain model, the time variation of line current and line pf have been predicted using PROMATLAB for both fixed and variable frequency operations of HPSRCB on the utility line. SPICE3 simulation results without active control and experimental results obtained from the bread board model for both open as well as closed loop fixed and variable frequency operations have been presented to verify the theory and design performance. / Graduate

Two new power conversion techniques, the constant-frequency zero-voltage-switching multiresonant-converter (CF ZVS-MRC) technique and the zero-voltage-switching technique that uses the magnetizing inductance of the power transformer as a resonant element {ZVS {L_M)) are proposed. analyzed, and evaluated for high-frequency applications. In addition, a novel design optimization approach for resonant type converters is introduced. Complete dc analysis of CF forward and half-bridge {HB) ZVS-MRCs are given, and the dc voltage-conversion-ratio characteristics for each of these two converters are derived. Graphic design procedures that maximize the efficiency and minimize current and voltage stresses are established. The design guidelines are verified on a 50 W CF forward ZVS-MRC operating with a switching frequency above 2 MHz, and on a 100 W HB ZVS-MRc operating with a switching frequency of 750 kHz. The ZVS (LM) technique is developed to eliminate the need for a large, inefficient external resonant inductor in ZVS resonant converters. This new family of isolated converters can operate with zero-voltage-switching of the primary active switches only (quasi-resonant (QR) operation) or with soft-switching of all semiconductor devices (multi-resonant (MR) operation). Furthermore, variable and constant frequency operation of all topologies in this new family of dc/dc converters are possible. A complete dc analysis of the HB ZVS-MRC (L_M) is given, and the dc voltage-conversion-ratio characteristics are derived. Design guidelines are defined using the same graphic method employed in the design of CF ZVS-MRCs. Constant frequency implementation of the HB ZVS-MRC (L_M) using controllable saturable inductors is also proposed. Finally, a novel approach to evaluate and design resonant converters based on the minimization of reactive power is developed. / Ph. D.

Two constant-frequency resonant power processors are discussed. The parallel resonant converter(PRC) with a controlled output rectifier can provide both forward and reverse power flow. A new control parameter — "θ-angle" is proposed for achieving output regulation and bidirectional power flow of the PRC. The θ-angle, measured as the displacement angle between the firing of the inverter switches and the firing of their corresponding output rectifier switches, provides a control-to-output characteristic independent of load variations and is very easy to implement. Unified closed-form expressions for the steady-state operating conditions are derived. Circuit performances are analyzed through closed-form solutions. Similar analyses are performed for a phase-controlled dual-inverter resonant converter. The feasibility of generating a regulated high-frequency AC bus employing this circuit is investigated. A controlled rectifier and LC filter type of load is used for the circuit to demonstrate the complex interactions between the inverters and the load and the effect of load power factor on the quality of the ac bus voltage. Desired operating regions for input, output, and various control parameters are analytically defined through closed-form solutions such that good quality ac bus voltage can be achieved. / M.S.

A steady-state analysis of a Constant-Frequency Parallel-Resonant Converter operating in the Clamped-Mode is performed for the continuous-conduction mode of operation (CCM). Unified closed-form expressions are derived for such circuit characteristics as the control to output, boundary conditions for natural commutation and forced commutation, and stresses on power devices. These characteristics are experimentally verified and simulated by using IO-SPICE. Considerations for practical design are discussed based on hardware operating at 300KHz, with a 300V input, 5V and 300W output. / M.S.

This thesis deals with the design of a power converter for induction heating of iron components designed for a power of at least 2.5 kW. The induction furnace forms a series resonant LC circuit. The thesis contains a description and a design of individual parts of the converter, including wiring diagrams and a design of printed circuit boards. At the end of the work are then described the mechanical construction, the course of recovery and testing the operation of the inverter.

This thesis deals with designing of an induction heating of small iron parts. This device should be primarily designed for a farrier practice or an artistic blacksmithing. Considering the practice, the referential heated iron part will be a horseshoe. The basis of this device is a power inverter with serial resonant circuit connected to inverter as a load. This thesis contains designing and development of electrical and mechanical parts of whole device. It means control circuits, resonant circuit, box for heated part, etc. At the end of this thesis is realization of the device, electrifying, optimization and testing. During the test the horseshoe was heated close to demanded temperature.