The goal of this thesis is to improve efficiency of an induction motor. In the first part, the working principle is described. The next part deals with the origin of losses and possible solutions to decreasing losses without impacting the production possibles. The third part of the thesis is focused on the calculation of parameters of a small serial production motor. In the fourth part, these parameters are verified using the analytical tool RMxprt which is included in Ansys Maxwell. The fifth chapter deals with the optimization using Matlab genetic algorithm. In the final chapter, the design modifications are verified using the method of finite element Ansys Maxwell 2D.

This work is focused on the design of the peristaltic pump drive for medical purposes. Its initial goal is closer introduction of peristaltic pumps and stepper motors. Then the design of BLDC motor will be made and the use of this motor will be compared with stepper motor. Design of the BLDC motor will be made using RMxprt. Last but not least simulations of both types of motors for the peristaltic pump will be created in Simplorer. Finally, the program LabVIEW will be introduced and a program for controlling a stepper motor will be created.

This work deals with a creation of model of synchronous generator in programmes such as Simplorer and Maxwell, and also its operation in an insular operation. In the paper are described Maxwells equations for solving electromagnetic field, theory of synchronous machine, further are briefly described a simulation programmes which were used. In the next part of work is described production of geometric model of generator and its later electromagnetic analysis in the Maxwell programmes environment. For a simulation of generators operation in insular operation were chosen 2 cases. The first case simulates an operation of generator at the step change of residence of R-L load, the second simulation an automatic regulation of voltage at the step change of residence of R-L load. The simulations were running in the Simplorer programme and at link simulation Maxwell Simplorer programmes.

This thesis deals with the design of electrical machine for direct drive of cascade liquid pumping system. At the beginning a suitable type of electrical machine and some of its basic parameters are selected. Finally, the 4 pole three phase induction machine powered by alternating voltage 3x400 V was chosen. After that complete design is made with respect to all specified requirements. The designed machine is analyzed with the use of ANSYS Maxwell and RMxprt software. The main outcome of the thesis are dimensional sketches of the engine that will be used as the basis for the production of the prototype.

This thesis provides complete design of generator into a spinning bike. The issue of current development is solved and the analytical design of the generator is made. The software Maxwell is being used for the analysis and optimization. On the basis of the obtained results is designed a model and a design drawing of the generator. The end of the thesis deals with the issue of connecting the generator to the mains supply and price calculation of the investment return.

This thesis is dealing with optimization by using artificial intelligence of an induction machine rotor slot. The one optimized is commonly manufactured induction motor with simple deep bar rotor. Goal is to design an optimization method and achieve the highest possible value of efficiency and power factor of chosen machine. Work contains the parametric model construction in Ansys Maxwell software, the optimization algorithm assembly and its setup for desirable output, and processing of the results.

The aim of this semester work is to analyze the losses of induction motor, according to their measure, use programs using the finite element method for the detection of the motor and the subsequent evaluation and comparison of the results obtained. The first part deals with the general AM, losses and measure their losses. The next section is very Lossmeasurement submitted asynchronous motors. The measured two machines have different characteristics in the sheet. The following section is calculating the losses using the finite element method using ANSYS Maxwell and RMXprt.The next part is the analysis of motor losses with a different number of rotor bars. This section is addressed to the models developed and validated by measuring the actual machine.

Given today’s trend with environment being very important, there has been an ongoing attempt in the rotating machine industry to create machines with highest efficiency possible. And so, permanent magnet synchronous machines represent types of machine with very high efficiency and are gradually replacing other machines in many applications. This work deals with familiarization of the properties of permanent magnet synchronous motor as well as typical design choices. The main focus of this work is the design of permanent magnet EC motor and following comparison of results obtained from analytical design and analysis in the RMxprt program. Finally, the results of design methods are compared.

This thesis is dedicated to efficiency increase of one phase induction machine through material change of induction cage and rotor slot shape optimization under the condition of maintaining the same locked-rotor torque. In the first part of this thesis is the explanation of induction machine principles. Next is the comparison of measured and simulated parameters of small one phase machine from ATAS company. The following part is dedicated to the analysis of rotor slot shape and ring size influence on machine parameters when using pure aluminum instead of resistive alloy. The next chapter deals with slot shape optimization in the program RMxprt, controlled by genetic algorithm written in MATLAB interface. In the final part are the resultant slot shapes simulated in Ansys Maxwell using finite element method and then the measured, simulated and expected parameters are compared.

This master’s thesis first deals with the theory concerning induction motor. It briefly desbribes the construction of three-phase induction motors, the generation of tractive force, power flow with loss distribution and also torque characteristic. In the next part an analytical calculation of the parameters of equivalent circuit for an existing induction motor with known dimensions is performed. After the calculation it is possible to find out the rated parameters of the motor, which makes it possible to further compare results with the values obtained by other methods. The next step was to create a model of the motor in RMxprt program, which is later also translated to ANSYS Maxwell 2D model. Simulations were carried out in both interfaces. As the next step the results obtained by the three methods are compared with measured values and also evaluated. The final part of the thesis focuses on the optimization of the magnetic circuit for higher frequencies. Efficiency of the modified induction motor is examined for higher frequencies using RMxprt Optimetrics and this procedure is performed for both default and alternative electrical steel materials.