This work deals with calculation and design of synchronous salient pole generator and then the transformation from this machine into so-called hybrid synchronous machine is described. This diploma thesis is done for company Siemens Electric Machines s.r.o. in Drásov. This company provided their design of synchronous salient pole generator. The model of this generator was created in programs RMxprt and Maxwell 2D. Suggestions and models were compared, and their calculated parameters were evaluated. The created model was upgraded to so-called hybrid synchronous generator. Permanent magnets were added in the created model and influence of these additional magnets is going to be analyzed. Tasks of the work are described in more details. in the introduction. The topic of synchronous generator and hybrid synchronous generator in general is described in the theoretical part. The next part of work deals with the design of salient pole generator. In the other part of the work calculation and design of the generator model are described in Ansys program. Furthermore there are some results from program compared with the results from company. Some model parts and other graphic outputs from Ansys program are shown. After that the creation of hybrid synchronous generator is described and created models of hybrid synchronous generators are compared and evaluated.

This master thesis deals in first part with basic theory of an induction motor and principle of function. It also includes theory about higher harmonics of magnetic field and how asynchronous and synchronous torques are created. Various ways how to decrease effect of these torques are suggested. These findings are later applied in practical analytical calculation in second part, in which all parameters of motor are calculated from given dimensions of motor from technical documentation. This is done for basic and higher harmonics. After that a model of this motor was created in RMxprt program, which also calculated all parameters of this motor and created torque characteristic. This motor was also modelled in ANSYS Maxwell 2D. Additional simulations for finding out influence of harmonics on torque characteristic were also done in this software. Torque characteristic of motor was also practically measured in laboratory. All results were compared and evaluated.

Permanent magnet synchronous machine (PMSM) are widely used in many industrial applications. This thesis starts with familiarization with the properties and structure of each type of synchronous machines with permanent magnets. Subsequently there are described properties and possible division of AC winding types. Afterward analytical designs of four machines with two different types of winding were realized. These designs were compared by means of simulations using the RMxprt program and their properties were subsequently verified by method of finite element using the Maxwell 2D program. Evaluation and comparison in terms of utility properties for all designs of machines were performed at the conclusion of this thesis.

This master thesis deals with optimization of the shape of the stator and rotor slots of induction motor with focusing on increasing efficiency. The theoretical part introduces the principles of optimization algorithms. Another part is devoted to design the shape of slots and its influence on the shape of slots on machine. On the models of motor was conducted the optimized shape of slots by using a genetic algorithm. Firstly, it was performed by using the analytical calculation in the RMxprt program, then by using the finite element method on two different models, whose difference simulates the influence of the production technology on the efficiency of the motor. Laboratory measurement was made on a real machine as well. The results of the measurement, calculations and optimizations are compared in the work.

The work deals with the analytical electromagnetic design of automotive claw-pole alternator 14V/120A. This design is verified in program Maxwell with a RMxprt tool. The results of both calculations are compared. Designed alternator is also compared with the results measured in the laboratory on the alternators of similar type. Furthermore, there are analyzed individual power losses of machine and listed options of reducing these losses, which results in an increase in overall efficiency.

This work is dedicated to increasing the effectiveness of a particular draft induction motor, which was before the change and subjected to laboratory measurements according to EN60034 - 2-1, an analytical calculation of the losses and the overall efficiency and analysis program RMxprt. The first part focuses on the analysis of measurement data, measurement of partial loss in the machine and overall efficiency. In the second chapter, losses and efficiency calculated analytically, in the first case using the links in the professional literature dealing with the design of electric motors and in the second case by a program for the rapid design of rotating electrical machines, RMxprt program. At the end of this chapter all parameters are obtained measurements and calculations are compared. The third chapter is devoted to the calculation of losses and the resulting efficiency machines in a computer program, in which I gradually adopted changes to increase the efficiency of electrical machines. It also shows the calculation of the new dimensions of the stator and rotor slots. In the fourth chapter, the preparation of documentation for the production of a new two-layer winding for the current machine, while preserving the original dimensions of stator slots. The last part is devoted to the analysis of measurement data on the supplied asynchronous motor with a newly designed stator winding. In conclusion then discussed the results of work.

Characteristics of synchronous machines with permanent magnets depend among others on geometric layout of the machine section. Unlike EC motors, where rectangular arrangement of quantities is suitable, these machines require sinusoidal behaviour. Specific forming of individual machine parts is partially derived from this requirement. This thesis deals with design of such machines, including various geometrical modifications of their sections and examination of influence of those modifications. The thesis includes also analytical calculation procedure of machine parameters as well as verification of final characteristics using the finite element method. It results in a combination of various design methods. FEMM, Maxwell RMxprt and Maxwell 2D Transient Analysis programs were used for verification. Individual modifications of machine geometries are applied to machines with concentrated windings with different ratio of number of slots and poles, and differences between machines and results of individual methods are compared.

The diplomatic thesis will describe the principle functions of synchronous motors with permanent magnets, for therein analysis of PMSM and BLDC motors. We will make calculation of the required parameters from the power unit for glider Discus 2. We will create a design of BLDC and PMSM motor from specified parameters. Features of the proposed engines will be verified with the help of the programs FEMM, RMxprt, Maxwell. At the end of the work will make conclusion about the diplamatic project and diffrences between PMSM and BLDC motor.

The aim of this master thesis is to get familiar with the influence of radial forces in the induction machine. Induction motor is one of the most commonly used and most extended type of machine, therefore it is useful to detect the intensity of theese forces and their influence at operation of the machine. In this work ,radial forces are computed by the software simulation in ANSYS Maxwell. Models are created with help of module Rmxprt and finite elements method.These models are based on real induction motors with predefined size of eccentricity. In the final part we perform a measurement of deviations on the real machine using vibrometer.

The thesis theme is the design of 3 MW high-speed permanent magnet synchronous motor. The work is divided into several parts, and contains the information given on the topic. The first part lists trends and new technologies of high-speed electric machines, and the issues and construction of high-speed synchronous machines are also listed here. In the second part, the machine is analytically designed from the specified values, which is then modelled in the RMxprt program. In the penultimate part, the engine is simulated by programs that are included in the ANSYS Electronics Desktop package, they are RMxprt and Maxwell. The modified engine model in RMxprt is simulated using defined formulas and then converted to Maxwell 2D, where the engine is simulated using the finite element method. In the last part, the results from the analytical calculation are compared with other high-speed machines. In addition, the results of simulations from RMxprt and Maxwell were compared in the last part.