<p> Lifted non-premixed turbulent jet flames in the Transverse Instability Combustor (TIC) have been analyzed using qualitative and quantitative methods. Lifted flames in the TIC have been observed to stabilize about zero to five injector exit diameters downstream of the dump plane into the chamber and exhibit pulsating, unsteady burning. Anchored flames immediately begin reacting in the injector recess and burn evenly in a uniform jet from the injector exit through the entire optically accessible region. Statistically significant, repeatable behavior lifted flames are observed. It is shown that the occurrence of lifted flames is most likely for an injector configuration with close wall-spacing, second greatest for a configuration with close middle-element spacing, and lowest for a configuration with even element-spacing. For all configurations, of those elements that have been observed to lift, the center element is most likely to lift while the second element from the wall was likely. Flames at the wall elements were never observed to lift. Evidence is shown to support that close injector element spacing and stronger transverse pressure waves aid lateral heat transfer which supports flame stability in the lifted position. It is hypothesized that the stability of lifted flames is influenced by neighboring ignition sources, often a neighboring anchored flame. It is also shown that instances of lifted flames increase with the root-mean-squared magnitude of pressure fluctuation about its mean (P’ RMS) up to a threshold, after which flames stabilize in the anchored recess position.</p> <p>Dynamic mode decomposition (DMD) and proper orthogonal decomposition (POD) analyses of CH* chemiluminescence data is performed. It is found that lateral ignition of the most upstream portion of lifted flames is dominated by the 1W mode. Furthermore, it is shown that low-frequency high energy modes with spatial layers resemble intensity-pulses, possibly attributable to ignition. These modes are trademarks of CH* chemiluminescent intensity data of lifted flames. It was also shown that the residence time in the chamber may be closely associated with those low-frequency modes around 200 Hz. DMD and POD were repeated for a downstream region on the center element, as well as a near-wall element, highlighting differences between the lifted flame dynamics in all three regions. </p> <p>It is shown that lifted flames are best characterized by their burning behavior and in rare cases may stabilize in the recess, while still being “lifted”. Furthermore, it is shown that flame position differentiation can extend into an initial period of highly stable combustor operation. Dynamic mode decomposition is explored as potential method to understand physical building blocks of proper orthogonal spatial layers. Non-visual indicators of lifted flames within the high-frequency (HF) pressure signal are sought to seek a method that allows for observation of lifted flames in optically inaccessible combustors, such as those in industry. Some attributes of power-spectral diagrams and cross-correlations of pressure signals are provided as potential indicators. </p>

A visualisation procedure was developed which predicts excited hydroxyl (OH*) radiation from the Computational Fluid Dynamics (CFD) solutions of cryogenic hydrogen-oxygen rocket flames. The model of backward ray tracing through inhomogeneous media with a continuously changing refractive index was implemented. It obtains the optical paths of light rays that originate in the rocket chamber, pass through the window and enter a simulated camera. Through the use of spectral modelling, the emission and absorption spectra eλ and κλ are simulated on the ray path from information about temperature, pressure and concentration of constituent species at relevant points. By solving a radiative transfer equation with the integration of emission and absorption spectra along the ray line-by-line, a spectral radiance is calculated, multiplied with the spectral filter transmittance and then integrated into total radiance. The values of total radiances at the window edge are visualised as a simulated 2D image. Such images are comparable with the OH* measurement images. The modelling of refraction effects results in up to 20 % of total radiance range absolute difference compared to line-of-sight integration. The implementation of accurate self-absorption corrects significant over-prediction, which occurs if the flame is assumed to be optically thin. Modelling of refraction results in images with recognisable areas where the effect of a liquid oxygen (LOx) jet core can be observed, as the light is significantly refracted. The algorithm is parallelised and thus ready for use on big computational clusters. It uses partial pre-computation of spectra to reduce computational effort.

This thesis is concerned with the development and application of laser induced thermal grating spectroscopy (LITGS) as a tool for thermometry in reacting and non-reacting flows. LITGS signals, which require resonant excitation of an absorbing species in the measurement region to produce a thermal grating, are acquired for systematic measurements of temperature in high pressure flames using OH and NO as target absorbing species in the burned gas. The signal obtained in LITGS measurements appears in the form of a time-based signal with a characteristic frequency proportional to the value or the sound speed of the local medium. With knowledge of the gas composition, the temperature can be derived from the speed of sound measurement. LITGS thermometry using resonant excitation of OH in the burned gas region of in oxygen enriched CH4/O2/N2 and CH4/air laminar flames was performed at elevated pressure (0.5 MPa) for a range of conditions. Measurements were acquired in oxygen enriched flames to provide an environment in which to demonstrate LITGS thermometry under high temperature conditions (up to 2900 K). The primary parameters that influence the quality of LITGS signal were also investigated. The signal contrast, which acts as a marker for the strength of the frequency oscillations, is shown to increase with an increase in the burnt gas density at the measurement point. LITGS employing resonant excitation of NO is also demonstrated for quantitative measurements of temperature in three environments – a static pressure cell at ambient temperature, a non-reacting heated jet at ambient pressure and a laminar premixed CH4/NH3/air flame operating at 0.5 MPa. Flame temperature measurements were acquired at various locations in the burned gas close to a water-cooled stagnation plate, demonstrating the capability of NO-LITGS thermometry for measuring the spatial distribution of temperature in combustion environments. In addition, the parameters that in influence the local temperature rise due to LITGS were also investigated in continuous vapour flows of acetone/air and toluene/air mixtures at atmospheric conditions. Acetone and toluene are commonly targeted species in previous LITGS measurements due to their favourable absorption characteristics. Results indicate that LITGS has the potential to produce accurate and precise measurements of temperature in non-reacting flows, but that the product of the pump intensity at the probe volume and the absorber concentration must remain relatively low to avoid significant localised heating of the measurement region.