Dispersed particle flows are encountered in many biological, geophysical but also in industrial situations, e.g. during processing of materials. In these flows, the particles usually are non-spherical and their angular dynamics play a crucial role for the final material properties. Generally, the angular dynamics of a particle is dependent on the local flow in the frame-of-reference of this particle. In this frame, the surrounding flow can be linearized and the linear velocity gradient will determine how the particle rotates. In this thesis, the main objective is to improve the fundamental knowledge of the angular dynamics of non-spherical particles related to two specific biobased material processes. Firstly, the flow of suspended cellulose fibers in a papermaking process is used as a motivation. In this process, strong shear rates close to walls and the size of the fibers motivates the study of inertial effects on a single particle in a simple shear flow. Through direct numerical simulations combined with a global stability analysis, this flow problem is approached and all stable rotational states are found for spheroidal particles with aspect ratios ranging from moderately slender fibers to thin disc-shaped particles. The second material process of interest is the production of strong cellulose filaments produced through hydrodynamic alignment and assembly of cellulose nanofibrils (CNF). The flow in the preparation process and the small size of the particles motivates the study of alignment and rotary diffusion of CNF in a strain flow. However, since the particles are smaller than the wavelength of visible light, the dynamics of CNF is not easily captured with standard optical techniques. With a new flow-stop experiment, rotary diffusion of CNF is measured using Polarized optical microscopy. This process is found to be quite complicated, where short-range interactions between fibrils seem to play an important role. New time-resolved X-ray characterization techniques were used to target the underlying mechanisms, but are found to be limited by the strong degradation of CNF due to the radiation. Although the results in this thesis have limited direct applicability, they provide important fundamental stepping stones towards the possibility to control fiber orientation in flows and can potentially lead to new tailor-made materials assembled from a nano-scale. / <p>QC 20160929</p>

Non-spherical particles are present all around us, in biological, industrial and environmental processes. Making predictions of their impact on us and systems in our vicinity can make life better for everyone here on earth. For example, the ash particles from a volcano eruption are non-spherical and their spreading in the atmosphere can hugely impact the air traffic, as was also proven in 2010. Furthermore, the orientation of the wood fibres in a paper sheet influences the final properties of the paper, and the cause of a specific fibre orientation can be traced back to the fluid flows during the manufacturing process of the paper. In this thesis, experimental and numerical work is presented with the goal to understand and utilize the behavior of elongated particles in fluid flows. Two different experimental setups are used. The first one, a turbulent half channel flow, aims at increasing the understanding of how particles with non-zero inertia behave in turbulence. The second setup is an attempt to design a flow field with the purpose to align nanofibrils and create high performance cellulose filaments. Experiments were performed in a turbulent half channel flow at different flow set- tings with dilute suspensions of cellulose acetate fibres having three different aspect ratios (length to width ratio). The two main results were firstly that the fibres agglom- erated in streamwise streaks, believed to be due to the turbulent velocity structures in the flow. Secondly, the orientation of the fibres was observed to be determined by the aspect ratio and the mean shear, not the turbulence. Short fibres were oriented in the spanwise direction while long fibres were oriented in the streamwise direction. In order to utilize the impressive properties (stiffness comparable to Kevlar) of the cellulose nanofibril in a macroscopic material, the alignment of the fibrils must be controlled. Here, a flow focusing device (resulting in an extensional flow), designed to align the fibrils, is used to create a cellulose filament with aligned fibrils. The principle is based on a separation of the alignment and the assembly of the fibrils, i.e. first align the fibrils and then lock the aligned structure. With this process, continuous filaments were created, with properties similar to that of the wood fibre at the same fibril alignment. However, the highest alignment (lowest angle) of the fibrils in a filament created was only 31o from the filament axis, and the next step is to increase the alignment. This thesis includes modeling of the alignment process with the Smoluchowski equation and a rotary diffusion. Finding a model that correctly describes the alignment process should in the end make it possible to create a filament with fully aligned fibrils. / <p>QC 20140908</p>