31 |
A study of the tissue culture and genetic manipulation of rubber (Hevea brasiliensis)Wilson, Zoe Amanda January 1989 (has links)
No description available.
|
32 |
Peroxide prevulcanization of natural rubber latexSaid, M. M. January 1989 (has links)
The peroxide prevulcanization of NR latex using a range of commercially-available organic peroxides and an inorganic peroxide (potassium peroxydisulphate), in both activated and non-activated systems, has been investigated. A range of reducing agents and compounds that are known to promote peroxide-initiated emulsion polymerization and peroxide curing of po1yesters have been evaluated as promoters for the peroxide prevulcanization of NR latex. A few reactive peroxyesters have been found to be effective as prevulcanizing agents at temperatures in the range 80 °C-lOO °C. the effectiveness of the prevulcanization systems was characterized by the rate and efficiency of crosslinking achieved by these systems. Fructose-activated peroxyester and fructoseactivated hydroperoxide systems were found to effect prevulcanization at temperatures in the range 50 °C-80 °C. There is no clear correlation between the structure/reactivity of peroxyesters and the effectiveness of fructose-activated prevulcanization systems. The relative reactivity of the alkoxy radicals generated by the commercial hydro peroxides PQ~tly exp\a~~s the differences in the effectiveness of various fructose-activated hydroperoxide prevulcanization systems. The prevulcanization kinetics for the fructose-activated t-butyl peroxyisobutyrate (tBPIB) system have been investigated. The overal rate of tBPIB decomposition in NR latex, in both non-activated and fructose-activated systems was found to be first-order reaction with respect to tBPIB concentration. However, investigation of initial rate of tBPIB decomposition in NR latex indicates that the initial rate of tBPIB decomposition in NR latex is half order with respect to initial tBPIB concentration. This is probably a consequence of induced decomposition of tBPIB by certain non-rubber substances, and_termination by recombination of radicals derived from tBPIB. But, the reason for the difference in the reaction order with respect to tBPIB concentration, at the initial stage of the reaction and during the run is not clear. The prevulcanization kinetics also exhibit a number of other peculiar characteristics. Thus at temperatures greater than 70°C, and using a high fructose concentration, the rate coefficient for crosslink formation tends to be greater than that for peroxide decomposition. This is probably attributed to the differences in the temperature-coefficients of the various competing reactions during peroxide prevulcanization of NR latex. The instantaneous crosslinking efficiency was found to increase linearly with prevulcanization time. At temperatures greater than 70°C, the instantaneous crosslinking efficiency can attain values greater than 50%, indicating the involvement of alkyl radicals as well as the alkoxy radicals in the crosslinking reaction. The experimental activation energies for peroxide decomposition and crosslink formation were found to decrease to apparently constant values with increasing fructose/ peroxide concentration ratio. The rate of tBPIB decomposition was found to be significantly determined by activation free energy and not just activation energy for the decomposition. The factors which influence the physical properties of films from peroxide-prevulcanized NR latex have been investigated. The crosslink concentration was found to be the most important factor in determining the physical properties of films from peroxide-prevulcanized NR latex. Factors that account for the differences in the physical properties of films from peroxide- and sulphur-prevulcanized latices, and peroxide gum NR vulcanizates have been discussed. Attempts to improve the ageing properties of films from peroxideprevulcanized NR latex indicate that a preventive antioxidant is an essential component for an effective antioxidant system for these films.
|
33 |
THE EFFECT OF FLOWERING ON RUBBER PRODUCTION IN GUAYULE (PARTHENIUM ARGENTATUM GRAY).Willard, Katherine Lucia. January 1985 (has links)
No description available.
|
34 |
A study of the partition of plasticizer and filler for highly hysteretic rubber blendsAhmad, Aris Bin January 1990 (has links)
No description available.
|
35 |
Factors affecting the formation of rubber from isopentenyl pyrophosphate in Hevea brasiliensis latexYusof, Faridah January 1996 (has links)
No description available.
|
36 |
Some aspects of the molecular structure of stretched rubbersStevenson, T. H. January 1988 (has links)
No description available.
|
37 |
Application of surface enhanced raman spectroscopy to measurements of diffusion through silastic membranesSutton, C. P. January 2000 (has links)
No description available.
|
38 |
Physiological and biochemical studies with rubber (Hevea brasiliensis) protoplastsButt, Adrian David January 1988 (has links)
No description available.
|
39 |
Characterisation and wear performance of HVOF sprayed Cr-xC-y-NiCr coatingsWirojanupatump, Sittichai January 2000 (has links)
No description available.
|
40 |
Modes of action of a fatty diamine surfactant on mechanical properties of natural rubber compoundsIsmail, Hanafi January 1994 (has links)
The modes of action of a diamine salt of fatty acid with a general structure of [RNHz+(CHz)JNH3+(R'COO-)z], referred to as a multifunctional additive (MFA) in carbon black and silica filled natural rubber (NR) compound have been studied. The mechanical properties have been enhanced by incorporating the MFA. Optimum mechanical properties for the natural rubber filled with carbon black compound are obtained at an MFA level which is estimated to give complete monolayer coverage of the carbon black surface. Studies on silica filled NR show a much higher optimum MFA level than for carbon black filled compounds, which is attributed to a different orientation of the MFA molecules at the silica-rubber interface. The MFA molecules may stand on the filler surface with their polar sites attached to its surface, giving rise to a much higher monolayer value. Filler dispersion, measured by computer-aided image analysis and scanning electron microscopy (SEM), showed that MFA gives improved dispersion at equivalent mixing time. The effect of the MFA on crosslink density of carbon black filled NR compounds was found to be small, in contrast to silica filled NR compounds, where the increase in crosslink density enhanced properties significantly. Techniques to examine the properties of compounds with and without MFA at equivalent levels of filler dispersion have been developed. Results show that, in addition to the improvement in filler dispersion, increased energy dissipation at the rubber-MFA-filler interfaces improves tear and tensile strength. A mechanism of adsorption to explain the mode of action of the MFA at the elastomer/filler interface has also been proposed.
|
Page generated in 0.0378 seconds