This thesis describes an investigation into vehicle handling control using active differentials in the rear axle of a motor vehicle. Such devices are able to transfer torque between the rear wheels and have traditionally been used to improve traction whilst minimising the impact on vehicle handling. However, the capacity to generate a lateral torque difference across an axle also gives them the potential to be used for yaw moment control. In order to generate a rigorous assessment of this potential, the investigation is carried out in three distinct phases. Firstly, an analysis of the scope for modifying vehicle handling given unrestricted control over torque transfer between the rear wheels is carded out in the simulation environment. For this purpose an idealised yaw sideslip controller is developed. This is used to show that an ideal active differential can have significant yaw moment authority in terms of generating both understeer and oversteer and that this can be used to actively modify a vehicle's handling balance and apply stability control at the limits of adhesion. In the second phase, the capabilities of two types of contemporary active differential, the torque vectoring differential (TVD) and active limited slip differential (ALSID), are then assessed against the ideal differential and against a brake based yaw moment controller. TVDs are found to be able to offer very similar performance to both their ideal counterpart and to the brake based system. They Gan also deliver this performance with a fraction of the energy loss that is observed in the brakes, thus making TVDs a viable proposition for applying continuous yaw control below the limits of adhesion. ALSDs, on the other hand do not offer equivalent functionality to an ideal active differential but are still shown to be very effective stability control devices. In the third phase, the ALSID results are validated on a prototype vehicle where it is shown that they do indeed offer substantial stability improvements both on high and low-P surfaces. However in order to deliver such benefits and be practical for implementation, it is also shown that significant redevelopment of the idealised controller is required. Finally, with the ALSID operating alongside a commercial brake based stability control system, it is proven that substantial reductions in brake intervention can be achieved without significant controller integration.

No description available.

ITC/USA 2006 Conference Proceedings / The Forty-Second Annual International Telemetering Conference and Technical Exhibition / October 23-26, 2006 / Town and Country Resort & Convention Center, San Diego, California / Telemetry data are usually collected for analysis at some later time and can be monitored to follow the progress of a test. In the case of an Air Data System the signals from the sensors are sent to a computer that calculates the air data parameters for use on multiple LabView-generated displays, as well as to the Data Acquisition System. The readouts on the multiple displays need to be real-time so they are useful to the flight crew. Equations that control the different air data values are determined by what telemetry data are available and the preference of those doing the test planning. These systems need to display the information in a format useful to the flight crew and be reliable.

Active vehicle safety systems for road vehicles play an important role in accident prevention. In recent years, rapid developments have been observed in this area with advancing technology and electronic control systems. Active yaw control is one of these subjects, which aims to control the vehicle in case of any impending spinning or plowing during rapid and/or sharp maneuver. In addition to the development of these systems, integration and cooperation of these independent control mechanisms constitutes the current trend in active vehicle safety systems design. In this thesis, design methodology and simulation results of an active yaw control system for two axle road vehicles have been presented. Main objective of the yaw control system is to estimate the desired yaw behavior of the vehicle according to the demand of the driver and track this desired behavior accurately. The design procedure follows a progressive method, which first aims to design the yaw control scheme without regarding any other stability parameters, followed by the development of the designed control scheme via taking other stability parameters such vehicle sideslip angle into consideration. A two degree of freedom vehicle model (commonly known as &ldquo / Bicycle Model&rdquo / ) is employed to model the desired vehicle behavior. The design of the controller is based on Fuzzy Logic Control, which has proved itself useful for complex nonlinear design problems. Afterwards, the proposed yaw controller has been modified in order to limit the vehicle sideslip angle as well. Integration of the designed active yaw control system with other safety systems such as Anti-Lock Braking System (ABS) and Traction Control System (TCS) is another subject of this study. A fuzzy logic based wheel slip controller has also been included in the study in order to integrate two different independent active systems to each other, which, in fact, is a general design approach for real life applications. This integration actually aims to initiate and develop the integration procedure of the active yaw control system with the (ABS). An eight degree of freedom detailed vehicle model with nonlinear tire model is utilized to represent the real vehicle in order to ensure the validity of the results. The simulation is held in MATLAB/Simulink environment, which has provided versatile design and simulation capabilities for this study. Wide-ranging simulations include various maneuvers with different road conditions have been performed in order to demonstrate the performance of the proposed controller.

This work is focused on the development of a thorough study about ISO standards focused on the vehicle dynamics, standardized tests of vehicle dynamics and measured variables that allow us to describe and model the behaviour of riding vehicles properly. In the Appendix A of the thesis, there is a list of all known ISO standards dealing with given topic. The standard ISO 15037-1 Road vehicles – Vehicle dynamics test methods, Part 1: General conditions for passenger cars is described in detail, including the forms for test reports and the Appendix C and D. In the thesis, there is also described a model of minimal needed measuring system that is still in good accordance with the standard ISO 15037-1 and fulfills all its requirements. Detailed description of all used sensors that are used to measure required variables is given, as well as a short description of all sensors that are used for measurement of other variables. After that, measurement abilities of the instrumentation of measuring system RIO used in ÚADI FSI Brno is compared and confronted with requirements given by the standard, to see, if all given criteria are properly fulfilled. Because of the fact that standard-given criteria are quite mild, while the equipment of the faculty is high-level technology, mostly made directly for measuring of dynamic parameters of the vehicles, including racing vehicles, the system is in full accordance with the standard ISO 15037-1.