Renewable or sustainable energy (SE) sources have attracted the attention of many countries because the power generated is environmentally friendly, and the sources are not subject to the instability of price and availability. This dissertation presents new trends in the DC-AC converters (inverters) used in renewable energy sources, particularly for photovoltaic (PV) energy systems. A review of the existing technologies is performed for both single-phase and three-phase systems, and the pros and cons of the best candidates are investigated. In many modern energy conversion systems, a DC voltage, which is provided from a SE source or energy storage device, must be boosted and converted to an AC voltage with a fixed amplitude and frequency. A novel switching pattern based on the concept of the conventional space-vector pulse-width-modulated (SVPWM) technique is developed for single-stage, boost-inverters using the topology of current source inverters (CSI). The six main switching states, and two zeros, with three switches conducting at any given instant in conventional SVPWM techniques are modified herein into three charging states and six discharging states with only two switches conducting at any given instant. The charging states are necessary in order to boost the DC input voltage. It is demonstrated that the CSI topology in conjunction with the developed switching pattern is capable of providing the required residential AC voltage from a low DC voltage of one PV panel at its rated power for both linear and nonlinear loads. In a micro-grid, the active and reactive power control and consequently voltage regulation is one of the main requirements. Therefore, the capability of the single-stage boost-inverter in controlling the active power and providing the reactive power is investigated. It is demonstrated that the injected active and reactive power can be independently controlled through two modulation indices introduced in the proposed switching algorithm. The system is capable of injecting a desirable level of reactive power, while the maximum power point tracking (MPPT) dictates the desirable active power. The developed switching pattern is experimentally verified through a laboratory scaled three-phase 200W boost-inverter for both grid-connected and stand-alone cases and the results are presented.

This paper presents a single-stage inverter with variable frequency modulation (VFM) based on LLC resonant converter. And LLC converter is a common topology of dc/dc conversion. LLC resonant converter can achieve high efficiency and soft-switching performance. Since the dc gain curve of the single-resonant LLC converter is flat when the switching frequency is larger than the resonant frequency, namely fs>fr, an additional L-C series resonant branch is paralleled to the original resonant tank to introduce higher-order-harmonic resonant current and a zero-gain point to the gain curve. Higher-order-harmonics help to deliver power and the zero-gain point enlarges the gain range which improves output THD and reduces the switching frequency range. A 1.2 kW prototype is built to demonstrate the performance of the proposed inverter. Zero-voltage-switching (ZVS) and zero-current-switching (ZCS) are achieved on the primary side and secondary side, respectively. And 97.3% efficiency and 2.17% voltage THD are achieved at full load condition, while 97.2% efficiency and 3.2% voltage THD are achieved at half load condition. / M.S. / The inverter is widely used to connect renewable energy into the grid by converting dc to ac waveform, like photovoltaic (PV) technology. Basically, the two-stage topology is usually used. The inverter would consist of two stages working in high frequency, the first stage is dc/dc converter which can regulate the input voltage to the desired bus voltage for the second stage, and the second stage is dc/ac converter. The first stage works at a specific switching frequency, so it can be designed to achieve higher efficiency in dc/dc conversion. The second stage also works at high switching frequency and converts dc to ac commonly by using SPWM which changes the duty cycle ratio in a sinusoidal pattern. The single-stage inverter only has one stage working in high frequency while the second stage works at twice line frequency. The first stage converts dc to rectified ac waveform and the second stage unfolds it to ac. The topology of LLC resonant converter being applied for the first stage of the single-stage inverter has been proposed. This topology uses variable-frequency-modulation (VFM) which varying switching frequency on the primary side to output different voltage levels. And it achieves zero-voltage-switching (ZVS). However, LLC converter can hardly output very low voltage due to the flat voltage gain curve at high frequency. Also, LLC converter only transfers the fundamental harmonic component to the load. If the higher-order harmonic components help transfer power when the switching frequency equals the resonant frequency, the current shape will be more like a square wave and the peak of resonant current can be reduced. This thesis proposes a topology that has two L-C resonant branches in parallel for the resonant tank in the converter. And the paralleled resonant branches produce a zero-gain frequency point into the gain curve so that the gain range is enlarged within the reduced switching frequency range and 3rd harmonic component of the resonant current helps to transfer power so that the rms value of resonant current can also be reduced.

Yes / The single-stage flyback Photovoltaic (PV) micro-inverter is considered as a simple and small in size topology but requires expensive digital microcontrollers such as Field-Programmable Gate Array (FPGA) or Digital Signal Processor (DSP) to increase the system efficiency, this would increase the cost of the overall system. To solve this problem, based on a single-stage flyback structure, this paper proposed a low cost and simple analog-digital control scheme. This control scheme is implemented using a low cost ATMega microcontroller built in the Arduino Uno board and some analog operational amplifiers. First, the single-stage flyback topology is analyzed theoretically and then the design consideration is obtained. Second, a 120 W prototype was developed in the laboratory to validate the proposed control. To prove the effectiveness of this control, we compared the cost price, overall system efficiency, and THD values of the proposed results with the results obtained by the literature. So, a low system component, single power stage, cheap control scheme, and decent efficiency are achieved by the proposed system. Finally, the experimental results present that the proposed system has a maximum efficiency of 91%, with good values of the total harmonic distortion (THD) compared to the results of other authors / This work was supported in-part by Innovate UK GCRF Energy Catalyst PiCREST project under Grant number 41358, in-part by British Academy GCRF COMPENSE project under Grant GCRFNGR3\1541

This thesis compares two methods of designing grid-tie inverters. The first design topology is a traditional two stage approach consisting of an isolated DC-DC converter on the input followed by a high switching frequency SPWM (Sinusoidal Pulse Width Modulation) stage to produce the required low frequency sine wave output. The novel second design approach employs a similar DC-DC input stage capable of being modulated to provide a rectified sine wave output voltage/current waveform. This stage is followed by a simple low frequency switched Unfolding Stage to recreate the required sine wave output. Both of the above designs have advantages and disadvantages depending on operating parameters. The following work will compare the Unfolding Output Stage and the SPWM Output Stage at various power levels and power densities. Input stage topologies are similarly examined in order to determine the best design approach for each output stage under consideration.