This dissertation presents the in-depth study and innovative solutions of the advanced integrated single-stage power-factor-correction (S2PFC) techniques, which target at the low- to medium-level power supplies, for wide range of applications, from power adapters and computers to various communication equipment. To limit the undesirable power converter input-current-harmonic's impact on the power line and other electronics equipment, stringent current harmonic regulations such as IEC 61000-3-2 have already been enforced. The S2PFC techniques have been proposed and intensively studied, in order to comply these regulations with minimal additional component count and cost. This dissertation provides a systematic study of the S2PFC input-current-shaping (ICS) mechanism, circuit topology generalization and variation, bulk capacitor voltage stress and switch current stress, converter design and optimization, and evaluation of the state-of-the-art S2PFC techniques with universal-line input. Besides, this presentation also presents the development of novel S2PFC techniques with a voltage-doubler-rectifier front end to both improve the performance and reduce the cost of S2PFC converters for (international voltage range) universal-line applications. The calculation and experimental results show that the proposed techniques offer a more cost-effective and efficient solution than industries' current practice, with universal-line input and converter power level up to 600 W. Finally, further improved technique is also presented with reduced filter inductor size and increased power density. / Ph. D.

This thesis mainly presents the design and implementation of a flyback converter with single-stage power factor correction. In the beginning, we propose different power factor collection (PFC) techniques referring to the inductor current of converter under three kinds of operation modes. In the continuous mode, we adopt the nonlinear-carrier control (NLC). Then, in the discontinuous mode and boundary mode, voltage-follower control (VFC) and transition mode technique control (TM) are adopted respectively. As to the converter analysis, we derive and verify the results of a small-signal model and perform equivalent circuit analysis by state-space averaging method, loss-free resistor (LFR) model, averaging method for two-time-scale system (AM), and current injected equivalent circuit approach (CIECA). Results derived from the above-mentioned models are compared and verified to be accurate of the system model. Furthermore, the control function and element design are implemented by simulation. We perform a PI controller to achieve better power factor based on results of analysis of the time and frequency domains analysis. Finally, three sets of different hardware are fabricated and verified depending on measured result and theoretical simulation.

This Thesis examines the operation and dynamic performance of a single-stage, single-switch power factor corrector, S4 PFC, with an integrated magnetic device, IM. Also detailed isthe development and analysis of a high power light emitting diode, HP LED, power factorcorrection converter and proposed voltage regulation band control approach.The S4 PFC consists of a cascaded discontinuous current mode, DCM, boost stage anda continuous current mode, CCM, forward converter. The S4 PFC achieves a high powerfactor, low input current harmonics and a regulated voltage output, utilising a singleMOSFET. A steady-state analysis of the S4 PFC with the IM is performed, identifying theoperating boundary conditions for the DCM power factor correction stage and the CCMoutput voltage regulation stage. Integrated magnetic analysis focuses on understanding theperformance, operation and generated flux paths within the IM core, ensuring the device doesnot affect the normal operation of the converter power stage. A design method for the S4 PFCwith IM component is developed along with a cost analysis of this approach. Analysis predictsthe performance of the S4 PFC and the IM, and the theoretical work is validated by MATLABand SABER simulations and measurements of a 180 W prototype converter.It is not only the development of new topological approaches that drives theadvancement of power electronic techniques. The recent emergence of HP LEDs has led to aflurry of new application areas for these devices. A DCM buck-boost converter performs thepower factor correction and energy storage, and a cascaded boundary conduction current modebuck converter regulates the current through the LED arrays. To match the useful operatinglifetime of the HP LEDs, electrolytic capacitors are not used in the PFC converter. Analysisexamines the operation and dynamic characteristics of a PFC converter with low capacitiveenergy storage capacity and its implications on the control method. A modified regulationband control approach is proposed to ensure a high power factor, low input current harmonicsand output voltage regulation of the PFC stage. Small signal analysis describes the dynamicperformance of the PFC converter, Circle Criterion is used to determine the loop stability.Theoretical work is validated by SABER and MATLAB simulations and measurements of a180 W prototype street luminaire.