1 |
MODELING OF THERMO-MECHANICAL BEHAVIOR OF NITINOL ACTUATOR FOR SMART NEEDLE APPLICATIONNguyen, Tuan Minh January 2012 (has links)
A large and increasing number of cancer interventions, including both diagnosis and therapy, involve precise placement of needles, which is extremely difficult. This challenge is due to lack of proper actuation of the needle (i.e., actuated from the proximal end, which is far away from the needle tip). To overcome this challenge, we propose to bend the needle using a smart actuator that applies bending forces on the needle body; thereby, improving the navigation of the needle. The smart actuator is designed with shape memory alloy (SMA) wires, namely Nitinol, due to their unique properties such as super-elasticity, shape memory effect, and biocompatibility. For accurate steering of the smart needle, there is a need to understand Nitinol thermo-mechanical behaviors. Various existing SMA constitutive models were investigated and compared. Since SMA is used as an actuator in this project, only one dimensional constitutive models are considered. Two distinct models with different phase transformation kinetic approaches were chosen. The first model was proposed by Terriault and Brailovski (J. Intell. Mat. Systems Structures, 2011) using a modified one dimensional Likhachev formulation. The second model was developed by Brinson (J. Intell. Mat. Systems Structures , 1993). Since all SMA constitutive models are empirically based, several important materials' constants such as Phase Transformation Temperatures are needed. The four Transformation Temperatures are: Martensite start (Ms), Martensite finish (Mf), Austenite start (As), Austenite finish (Af). Differential Scanning Calorimetry (DSC) was used to obtain these constants. These temperatures are also influenced by stress, defined by the Clausius-Clayperon coefficients. The coefficients were obtained by measuring Nitinol temperature and displacement response under various constant stress conditions. In order to study its actuation behavior, Nitinol wires under constant strain configuration and resistance heating were tested for their force response. The thermo-mechanical responses were then compared with numerical simulations. While Terriault and Brailovski resistance heating formulation agrees strongly with temperature responses, the model cannot be used to simulate the actuator mechanical responses. Brinson model simulations of the force responses were found to agree well with experimental results. In conclusion, Terriault and Brailovski resistance heating formulation should be coupled with Brinson model to accurately simulate Nitinol actuation behavior for the smart needle. / Mechanical Engineering
|
2 |
THERMOMECHANICAL CHARACTERIZATION OF ONE-WAY SHAPE MEMORY NITINOL AS AN ACTUATOR FOR ACTIVE SURGICAL NEEDLEHonarvar, Mohammad January 2014 (has links)
Needle-based intervention insertion is one of the common surgical techniques used in many diagnostic and therapeutic percutaneous procedures. The success of such procedures highly depends on the accuracy of needle placement at target locations. An active needle has the potential to enhance the accuracy of needle placement as well as to improve clinical outcome. Bending forces provided by the attached actuators can assist the maneuverability in order to reach the targets following a desired trajectory. There are three major research parts in the development of active needle project in the Composites Laboratory of Temple University. They are thermomechanical characterization of shape memory alloy (SMA) or Nitinol as an actuator for smart needle, mechanical modeling and design of smart needles, and study of tissue needle interaction. The characterization of SMA is the focus of this dissertation. Unique thermomechanical properties of Nitinol known as shape memory effect and superelasticity make it applicable for different fields such as biomedical, structural and aerospace engineering. These unique behaviors are due to the comparatively large amount of recoverable strain which is being produced in a martensitic phase transformation. However, under certain ranges of stresses and temperatures, Nitinol wires exhibit unrecovered strain (also known as residual strain); which limits their applicability. Therefore, for applications that rely on the strain response in repetitive loading and unloading cycles, it is important to understand the generation of the unrecovered strain in the Nitinol wires. In this study, the unrecovered strain of Nitinol wires with various diameters was investigated, using two experimental approaches: constant stress and uniaxial tensile tests. Moreover, a critical range of stress was found beyond which the unrecovered strain was negligible at temperatures of 70 to 80C depending on the wire diameter. Wire diameters varied from 0.10 to 0.29 mm were tested and different ranges of critical stress were found for different wire diameters. The transformation temperatures of different wire diameters at zero stress have been achieved by performing the Differential Scanning Calorimetry (DSC) test. The actuation force created by Nitinol wire is measured through constant strain experiment. X-Ray Diffraction (XRD) study was also performed to investigate the phase of Nitinol wires under various thermomechanical loading conditions. In summary, the effect of wire diameter on the required critical stresses to avoid the unrecovered strain between first and second cycle of heating and cooling are presented and the results of both mechanical tests are justified by the results obtained from the XRD study. / Mechanical Engineering
|
Page generated in 0.0386 seconds