Spelling suggestions: "subject:"sont array"" "subject:"sont spray""
1 |
Comparison and Investigation of Solar Spectral Irradiance with Solar Aspect MonitorLin, Ying-Tsen 30 September 2014 (has links)
On-board the International Space Station (ISS), the Remote Atmospheric and Ionospheric Detection System (RAIDS) is a suite of limb-scanning monitors taking measurements from the extreme ultraviolet (EUV) to the near infrared (NIR). A single-scattering Rayleigh model is developed to eliminate the scattered brightness below 90 km and an inversion technique is applied on limb-scanned radiance profiles at 236.5 nm, NO (0,1) gamma band. The ISS orbit allows observations from 7:00 to 16:00 local hours over a one-month period from mid-June to mid-July of 2010 and observation of the local-time variation of NO abundance in the lower thermosphere is derived. The uniquely stable solar activity during 2010 allows the local time variation of NO to be observed with limited influence of solar variability. The comparison with a 1D model shows good agreement at altitude above 120 km, suggesting that most of the local time variation of NO is due to solar illumination, radiation, chemistry, and vertical diffusion.
Solar soft X-ray is the major driver of the variability observed in the ionospheric and thermospheric constituents at the equatorial region. Over the years measurements in these wavelengths are scarce and discrepancies lie among the existing data. The Solar Aspect Monitor (SAM) is a pinhole camera on the Extreme-ultraviolet Variability Experiment (EVE) flying on the Solar Dynamics Observatory (SDO). Every 10 seconds SAM projects the solar disk onto the CCD through a metallic filter designed to allow only solar photons shortward of 7 nm to pass. Contamination from energetic particles and out-of-band irradiance is, however, present. The broadband (BB) technique is developed for isolating the 0.1 to 7 nm integrated irradiance to produce broadband irradiance. The results agree with the zeroth-order product from the EUV SpectroPhotometer (ESP) with 25% regardless of solar activity level. Active regions in the solar atmosphere are tracked by the Apertural Progression Procedure for Light Estimate (APPLE). The photon event detection (PED) algorithm takes both BB and APPLE results as prior information to extract in-band photons. Applications of the PED products, including solar feature studies and spectral resolved irradiance, are demonstrated. / Ph. D.
|
2 |
Resonant Soft X-Ray Emission Spectroscopy of Vanadium Oxides and Related Compounds / Resonant Mjukröntgenemissionsspektroskopi av Vanadinoxider och Relaterade FöreningarSchmitt, Thorsten January 2004 (has links)
<p>This thesis addresses the electronic structure of vanadium and copper oxides using soft X-ray absorption (SXA) spectroscopy and resonant inelastic X-ray scattering (RIXS) at high brightness synchrotron radiation sources. In RIXS incident photons, tuned to the energy of specific absorption resonances, are inelastically scattered leaving behind a low energy valence excitation in the system studied. Effects of electron localization are reflected by the occurrence of low-energy excitations in form of dd- and charge-transfer excitations that are modelled by cluster calculations. Band-like states are dominating when the intermediate core excited state is delocalized.</p><p>RIXS at V 2p and O 1s resonances has been used to study the electronic structure of the monovalent vanadium oxides VO<sub>2</sub> and V<sub>2</sub>O<sub>3</sub>, and of the mixed valence compounds, NaV<sub>2</sub>O<sub>5</sub> and V<sub>6</sub>O<sub>13</sub>. For NaV<sub>2</sub>O<sub>5</sub> and V<sub>6</sub>O<sub>13</sub> significant contributions from localized low-energy excitations reflect the partly localized character of their valence band electronic structure, whereas VO<sub>2</sub> and V<sub>2</sub>O<sub>3</sub> appear mostly as band-like. Effects of carrier doping are addressed for the case of Mo doping into VO<sub>2</sub> and reveal a quasi-rigid band behavior. In the cases of VO<sub>2</sub> and V<sub>6</sub>O<sub>13</sub> the temperature dependent metal-insulator transition could be monitored by following the spectral evolution of bands originating from V 3d and V 3d - O2p hybridized states. For Na<sub>2</sub>V<sub>3</sub>O<sub>7</sub> nanotubes it was possible to selectively probe states from the apical and the basal oxygen sites of VO<sub>5</sub> pyramids that constitute these nanotubes. Furthermore, the RIXS technique has been demonstrated to be highly valuable in characterizing the charge transfer processes that accompany lithium insertion into vanadium oxide battery cathodes. Finally, for insulating cuprates RIXS at O 1s, Cu 3p and Cu 3s resonances has been recorded at high-resolution for the detailed investigation of crystal field excitations.</p>
|
3 |
Resonant Soft X-Ray Emission Spectroscopy of Vanadium Oxides and Related Compounds / Resonant Mjukröntgenemissionsspektroskopi av Vanadinoxider och Relaterade FöreningarSchmitt, Thorsten January 2004 (has links)
This thesis addresses the electronic structure of vanadium and copper oxides using soft X-ray absorption (SXA) spectroscopy and resonant inelastic X-ray scattering (RIXS) at high brightness synchrotron radiation sources. In RIXS incident photons, tuned to the energy of specific absorption resonances, are inelastically scattered leaving behind a low energy valence excitation in the system studied. Effects of electron localization are reflected by the occurrence of low-energy excitations in form of dd- and charge-transfer excitations that are modelled by cluster calculations. Band-like states are dominating when the intermediate core excited state is delocalized. RIXS at V 2p and O 1s resonances has been used to study the electronic structure of the monovalent vanadium oxides VO2 and V2O3, and of the mixed valence compounds, NaV2O5 and V6O13. For NaV2O5 and V6O13 significant contributions from localized low-energy excitations reflect the partly localized character of their valence band electronic structure, whereas VO2 and V2O3 appear mostly as band-like. Effects of carrier doping are addressed for the case of Mo doping into VO2 and reveal a quasi-rigid band behavior. In the cases of VO2 and V6O13 the temperature dependent metal-insulator transition could be monitored by following the spectral evolution of bands originating from V 3d and V 3d - O2p hybridized states. For Na2V3O7 nanotubes it was possible to selectively probe states from the apical and the basal oxygen sites of VO5 pyramids that constitute these nanotubes. Furthermore, the RIXS technique has been demonstrated to be highly valuable in characterizing the charge transfer processes that accompany lithium insertion into vanadium oxide battery cathodes. Finally, for insulating cuprates RIXS at O 1s, Cu 3p and Cu 3s resonances has been recorded at high-resolution for the detailed investigation of crystal field excitations.
|
4 |
Compact Soft X-Ray MicroscopyJohansson, Göran January 2003 (has links)
This thesis describes the development of soft x-rayreflective optics, instrumentation and applications for compactsoft x-ray microscopy. The microscope is based on a table-topliquid-jet-target laser-plasma source in combination with aspherical normal-incidence multilayer condenser mirror andnanofabricated diffractive optics for imaging. High-resolutionimaging is performed at the wavelength 3.374 nm in thewater-window (2.3 - 4.4 nm), where natural contrast betweencarbon and oxygen allows imaging of unstained biologicalmaterial in their natural aqueous environment. The design and implementation of a compact soft x-rayreflectometer based on a laser-plasma source is described. Thereflectometer allows rapid and accurate characterization ofnormal-incidence multilayer coatings used at water-windowwavelengths. This instrument, which measures absolutereflectivity and multilayer period, is now used in thefabrication process, aiming to improve the soft x-raynormal-incidence multilayer condenser system of the compactsoft x-ray microscope. Latest results from the developmentprocess are presented. A new design of the compact soft x-ray microscope, withimprovements in mechanical and thermal stability, providesuser-friendly and daily operation. This includes also a newnozzle design for the liquid-jet-target laser-plasma source,which enables higher source stability and operation withcryogenic liquids. In addition, a new experimental arrangementunder construction is briefly described. It will utilize acondenser zone plate and operate at the wavelength 2.478nm. Finally, performance test of the compact soft x-raymicroscope is presented and discussed. In addition, a projectto explore the use of soft x-ray microscopy for imaging sensorycells is described. The high-resolution imaging of these cellswas performed at the synchrotron-based soft x-ray microscope atLawrence Berkeley National Laboratory (LBNL).
|
5 |
Compact Soft X-Ray Microscopy : Sources, Optics and InstrumentationTakman, Per January 2007 (has links)
This thesis describes the development of a sub-60-nm full-period resolution compact soft x-ray microscope operating in the water-window region (2.3-4.4 nm). Soft x-ray water-window microscopy is a powerful technique for high-resolution imaging of organic materials exploiting the natural contrast mechanism between carbon and oxygen, cf. Sect. 4.1. The thesis discusses the components of, as well as the integration of the microscope, including liquid-jet laser-plasma x-ray sources, optics, simulations, and image-processing tools. Liquid-jet-target laser-plasma sources for generation of soft x-rays and extreme-ultraviolet radiation are compact sources with high brightness. The work focused on improved target stability, decreased debris, and accurate source characterization. For x ray microscopy applications a liquid-jet target delivery system allowing cryogenic liquids was developed. Source characterization was performed for two different liquid-jet targets: Methanol and liquid nitrogen. For extreme-ultraviolet lithography applications, the potential use of a liquid-tin-jet laser-plasma source was explored including conversion efficiency and debris measurements. High quality optics are essential in the development of compact x-ray microscopes. For soft x-ray wavelengths, zone plates and multilayer mirrors are used to focus or redirect radiation. This thesis describes the development and characterization of a condenser zone plate suitable for use in a compact soft x-ray microscope operating at λ = 2.478 nm. It also investigates the possibility to perform differential interference contrast microscopy in the water window using a single diffractive optical element. An arrangement for rapid and accurate determination of absolute and local diffraction efficiency of soft x-ray zone plates using a compact laser-plasma source has been developed. The instrument is used to characterize the zone plates fabricated at the Biomedical & X-Ray Physics division at KTH. Through a collaboration with the Fraunhofer-Institut in Jena, Germany, a large diameter spherical Cr/Sc multilayer mirror, suitable as condenser in the compact x-ray microscope, was developed and characterized. The mirror is designed for λ = 3.374 nm and shows a high, and uniform reflectivity of 3%. This increases the photon flux by an order of magnitude compared to the W/B4C mirrors previously used. The thesis describes the development of a compact soft x-ray microscope with sub-60-nm full-period resolution. It can operate at two different wavelengths in the water window using the soft x-ray laser-plasma sources combined with the condenser optics described above. Imaging is performed by zone plate objectives. The microscope is capable of imaging hydrated biological samples with thicknesses up to ~10 μm. Improvements made to the mechanical design has turned it into a user friendly instrument allowing daily operation. A numerical method was developed to study the effects of partially coherent illumination on 2D imaging. To stimulate experiments on functional imaging in x-ray microscopy an image-analysis algorithm for identifying colloidal-gold particles was developed. Size selective identification and localization of single gold particles down to a diameter of 50 nm was demonstrated. / QC 20100819
|
6 |
Phase-Contrast and High-Resolution Optics for X-Ray Microscopyvon Hofsten, Olof January 2010 (has links)
X-ray microscopy is a well-established technique for nanoscale imaging. Zone plates are used as microscope objectives and provide high resolution, approaching 10 nm, currently limited by fabrication issues. This Thesis presents zone plate optics that achieve either high resolution or phase contrast in x-ray microscopy. The high-resolution optics use high orders of the zone plate, which alleviates the demands on fabrication, and the phase-contrast optics are single-element diffractive optical elements that produce contrast by Zernike or differential-interference contrast methods. The advantage of phase contrast in x-ray microscopy is shorter exposure times, and is crucial in the hard x-ray regime. Microscopy in the absorption‑contrast region of the water-window (2.34 - 4.37 nm) also benefits from these optics. The development of the optics for a laboratory soft x-ray microscope spans from theoretical and numerical analysis of coherence and stray light to experimental implementation and testing. The laboratory microscope uses laser-produced plasma-sources in the water-window and is unique in its design and performance. It will be shown that the laboratory microscope in its current form is a user-oriented and stable instrument, and has been used in a number of applications. The implementation of a cryogenic sample stage for tomographic imaging of biological samples in their natural environment has enabled applications in biology, and 3D x-ray microscopy of cells was performed for the first time with a laboratory instrument. / QC 20101130
|
7 |
Spectroscopic analysis of selected silicon ceramicsLeitch, Sam Anthony 17 June 2005
<p>Silicon ceramics are popular in both commercial applications and material research. The purpose of this thesis is to present measurements and analysis of four different silicon ceramics: á, â and ã phases of silicon nitride and silicon oxynitride using soft x-ray spectroscopy, which analyses the electronic structure of materials by measuring the absorption and emission of x-ray radiation. Absorption and emission spectra of these materials are presented, many of which have not be previously documented. The results are compared to model spectra and together they provide information about the electronic structure of the material.</p><p>Assignments of emission features to element, orbital, and site symmetry are performed for each material. Combinations of silicon and nitrogen emission spectra provide insight into the strained bonding structure of nitrogen. It is concluded that p-dð interaction plays a role in the bonding arrangement of nitrogen and oxygen sites within these structures. The emission features of non-equivalent silicon sites within ã-Si3N4 are identified, which represents some of the first analysis of same element, non-equivalent sites in a material.</p><p>Silicon absorption and emission spectra were plotted on the same energy scale to facilitate measurement of the band gap. Since previously measured band gaps are not well represented in literature, the measured band gaps were compared to values predicted using DFT calculations. The band gap values are in reasonable agreement to calculated values, but do not vary as widely as predicted.</p>
|
8 |
Determining the sp²/sp³ bonding concentrations of carbon filmsHamilton, Trenton David 22 July 2005
Analysis of the electronic structures of nitrogen-doped, amorphous carbon samples and of nanodiamond films are carried out in order to determine their sp2 bonding concentration. The amorphous carbon samples under consideration are deposited onto polytetrafluoroethylene (PTFE) polymer substrates by hot wire plasma sputtering of graphite in varying nitrogen concentration atmospheres. The deposition or modification of the substrates surface may lend itself to increasing hardness and wear resistance. Eventually these polymer substrates may be used for applications in the field of biomaterials, focusing on cardiovascular surgery, where a low blood/surface interaction is important.
The primary technique used in this study is x-ray absorption spectroscopy, measured at the Advanced Light Source synchrotron at the Lawrence Berkeley National Laboratory, Berkeley, USA. A method of analyzing these spectra was then developed to determine the sp2 bonding concentrations in carbon films.
Through this newly developed analysis method, the sp2 bonding concentrations in these samples increases from 74 to 93% with growing nitrogen doping. The diamond films presented here are deposited on silicon wafer substrates in a methane atmosphere by microwave plasma deposition. Various deposition conditions, such as bias voltage and methane atmosphere concentration, affect the purity of the diamond film. This analysis reveals sp2 bonding concentrations in these samples from, typically, a few percent to 25%.
|
9 |
Determining the sp²/sp³ bonding concentrations of carbon filmsHamilton, Trenton David 22 July 2005 (has links)
Analysis of the electronic structures of nitrogen-doped, amorphous carbon samples and of nanodiamond films are carried out in order to determine their sp2 bonding concentration. The amorphous carbon samples under consideration are deposited onto polytetrafluoroethylene (PTFE) polymer substrates by hot wire plasma sputtering of graphite in varying nitrogen concentration atmospheres. The deposition or modification of the substrates surface may lend itself to increasing hardness and wear resistance. Eventually these polymer substrates may be used for applications in the field of biomaterials, focusing on cardiovascular surgery, where a low blood/surface interaction is important.
The primary technique used in this study is x-ray absorption spectroscopy, measured at the Advanced Light Source synchrotron at the Lawrence Berkeley National Laboratory, Berkeley, USA. A method of analyzing these spectra was then developed to determine the sp2 bonding concentrations in carbon films.
Through this newly developed analysis method, the sp2 bonding concentrations in these samples increases from 74 to 93% with growing nitrogen doping. The diamond films presented here are deposited on silicon wafer substrates in a methane atmosphere by microwave plasma deposition. Various deposition conditions, such as bias voltage and methane atmosphere concentration, affect the purity of the diamond film. This analysis reveals sp2 bonding concentrations in these samples from, typically, a few percent to 25%.
|
10 |
Spectroscopic analysis of selected silicon ceramicsLeitch, Sam Anthony 17 June 2005 (has links)
<p>Silicon ceramics are popular in both commercial applications and material research. The purpose of this thesis is to present measurements and analysis of four different silicon ceramics: á, â and ã phases of silicon nitride and silicon oxynitride using soft x-ray spectroscopy, which analyses the electronic structure of materials by measuring the absorption and emission of x-ray radiation. Absorption and emission spectra of these materials are presented, many of which have not be previously documented. The results are compared to model spectra and together they provide information about the electronic structure of the material.</p><p>Assignments of emission features to element, orbital, and site symmetry are performed for each material. Combinations of silicon and nitrogen emission spectra provide insight into the strained bonding structure of nitrogen. It is concluded that p-dð interaction plays a role in the bonding arrangement of nitrogen and oxygen sites within these structures. The emission features of non-equivalent silicon sites within ã-Si3N4 are identified, which represents some of the first analysis of same element, non-equivalent sites in a material.</p><p>Silicon absorption and emission spectra were plotted on the same energy scale to facilitate measurement of the band gap. Since previously measured band gaps are not well represented in literature, the measured band gaps were compared to values predicted using DFT calculations. The band gap values are in reasonable agreement to calculated values, but do not vary as widely as predicted.</p>
|
Page generated in 0.0618 seconds