No description available.

The behavior of unsaturated soils depends heavily on material properties and soil conditions. In Geotechnical Engineering, compacted soils are frequently used as fill material, and quality control is vital to the construction process. There are few methods available to estimate the parameters associated with unsaturated soils based on field measurements, and a relationship between these factors could reduce testing time and lower construction costs. Undrained triaxial tests were performed on four clays representing a range of material properties in an effort to reach the maximum dry density, which provides the highest bearing capacity. Each clay was compacted at optimum moisture content, as well as wet and dry of optimum. Measurements were taken using the GeoGauge and shear wave velocities. An empirical approach was used to estimate the effect of a density gradient on soil suction. A relationship between the normal stress and matric suction produced a strong trend when plotted against a function of stiffness and the void ratio, which represents a density gradient. Another relationship between the GeoGauge and shear wave stiffness measurements was found, but no relationship with the material properties of the samples was observed, indicating that more in-depth research is needed to find a stronger relationship.

No description available.

In order to avoid the occurrence of early-age damage, cement-treated base (CTB) materials must be allowed to cure for a period of time before the pavement can be opened to traffic. The purpose of this research was to evaluate the utility of the soil stiffness gauge (SSG), heavy Clegg impact soil tester (CIST), portable falling-weight deflectometer (PFWD), dynamic cone penetrometer, and falling-weight deflectometer for assessing early-age strength gain of cement-stabilized materials. Experimentation was performed at four sites on a pavement reconstruction project along Interstate 84 near Morgan, Utah, and three sites along Highway 91 near Richmond, Utah; cement stabilization was used to construct CTB layers at both locations. Each site was stationed to facilitate repeated measurements at the same locations with different devices and at different curing times. Because of the considerable attention they have received in the pavement construction industry for routine quality control and quality assurance programs, the SSG, CIST, and PFWD were the primary focus of the research. Statistical techniques were utilized to evaluate the sensitivity to curing time, repeatability, and efficiency of these devices. In addition, the ruggedness and ease of use of each device were evaluated. The test results indicate that the CIST data were more sensitive to curing time than the SSG and PFWD data at the majority of the cement-treated sites during the first 72 hours after construction. Furthermore, the results indicate that the CIST is superior to the other instruments with respect to repeatability, efficiency, ruggedness, and ease of use. Because the CIST is less expensive than the SSG and PFWD, it is more likely to be purchased by pavement engineers and contractors involved with construction of CTBs. For these reasons, this research suggests that the CIST offers greater overall utility than the SSG or PFWD for monitoring early-age strength gain of CTB. Further research is needed to identify appropriate threshold CIST values at which CTB layers develop sufficient strength to resist permanent deformation or marring under different types of trafficking.

A relatively new method used to reduce the amount of cement-treated base (CTB) shrinkage cracking is microcracking of the CTB shortly after construction. Three portable instruments used in this study for monitoring the microcracking process include the heavy Clegg impact soil tester (CIST), portable falling-weight deflectometer (PFWD), and soil stiffness gauge (SSG). The specific objectives of this research were 1) to evaluate the sensitivity of each of the three portable instruments to microcracking, and 2) to compare measurements of CTB stiffness reduction obtained using the three devices. The test locations included in this study were Redwood Drive and Dale Avenue in Salt Lake City, Utah; 300 South in Spanish Fork, Utah; and a private access road in Wyoming. Experimental testing in the field consisted of randomized stationing at each site; sampling the CTB immediately after the cement was mixed into the reclaimed base material; compacting specimens for laboratory testing; and testing the CTB immediately after construction, immediately before microcracking, immediately after each pass of the vibratory roller during the microcracking process, and, in some instances, three days after microcracking. Several linear regression analyses were performed after data were collected using the CIST, PFWD, and SSG during the microcracking process to meet the objectives of this research. Results from the statistical analyses designed to evaluate the sensitivity of each of the three portable instruments to microcracking indicate that the PFWD and SSG are sensitive to microcracking, while the CIST is insensitive to microcracking. Results from the statistical analyses designed to compare measurements of CTB stiffness reduction demonstrate that neither of the instrument correlations involving the CIST are statistically significant. Only the correlation between the PFWD and SSG was shown to be statistically significant. Given the results of this research, engineers and contractors should utilize the PFWD or SSG for monitoring microcracking of CTB layers. The heavy CIST is unsuitable for monitoring microcracking and should not be used. For deriving target CTB stiffness reductions measured using either the PFWD or SSG from specified targets measured using the other, engineers and contractors should utilize the correlation chart developed in this research.

The first objective of this research was to investigate temporal trends in the mechanical properties of base materials stabilized with asphalt emulsion and to assess the rate at which emulsion-treated base (ETB) design properties are achieved. The second objective of this research was to identify construction and environmental factors most correlated to specific mechanical properties of ETB layers and to determine which construction factors exhibit the greatest variability. Additional statistical analysis was performed to determine if significant differences existed between different test sections on a given project. In this research, three experimental sections were established along a pavement reconstruction project near Saratoga Springs, Utah. Field tests were performed to assess the structural properties of the ETB immediately following construction and at 2, 3, 7, and 14 days; 4 months; and 1 year. Measured values were plotted against time to determine trends in ETB strength development. Several statistical analyses were then performed on the collected data. Modulus values were consistently low in all three sections during the first two weeks of testing, increased dramatically by 4 months, and then decreased considerably by 1 year. During the first two weeks following construction, the average ETB structural coefficient was 0.04. Only two of the three sections reached the design structural coefficient of 0.25, which occurred after approximately 3 months; however, the average structural coefficient measured for all three sections after 1 year of curing, which included a winter, was only 47 percent of the design strength. The results of this research show that, while pavement capacity is sufficient at 4 months, it is severely reduced during the first two weeks and at 1 year. Trafficking under these reduced capacities is not recommended. Statistical analysis showed that gradation, binder change during emulsion treatment, and moisture content have the most significant impact on ETB structural properties. Gradation and binder change during emulsion treatment also exhibited significant variability; tighter specifications on material gradations and improved uniformity in emulsion distribution should therefore be considered. Because of the negative impacts of moisture on ETB strength development, construction should not be performed in conditions of excess moisture.