Thesis (Ph. D.)--School of Physics, Faculty of Science, University of Sydney, 2004. / Bibliography: leaves 116-123.

Thesis (Ph. D.)--University of Sydney, 2004. / Title from title screen (viewed 14 May 2008). Submitted in fulfilment of the requirements for the degree of Doctor of Philosophy to the School of Physics, Faculty of Science. Includes bibliographical references. Also available in print form.

University of Macau / Faculty of Science and Technology. / Department of Electromechanical Engineering

Thesis (Ph.D.)--Australian National University, 2004.

High Concentrated Photovoltaics (H-CPV) promise a more efficient, higher power output than traditional photovoltaic modules. This is achieved by concentrating sunlight onto a small triple junction (CTJ) InGaP/InGaAs/Ge cell (ranging from 3.14 mm2 to 1 cm2) by using precision optical systems. These systems utilise non-imaging optics to concentrate and distribute the incident solar flux uniformly onto the CTJ device receiver to achieve maximum performance and power output from an H-CPV module. However, the performance of the device can be reduced due to the partial or complete absorption of a range of wavelengths present in the solar spectrum by the optical materials that are used for concentration. An investigation to determine the current density topographies of each subcell in a CTJ cell by multiple raster scans of an optical fibre receiver of a spectrometer in the plane of the aperture of the secondary’s optical element was conducted. Results showed that the physical properties of the optical elements’ material absorbed different amounts of the spectral content with respect to the subcell photosensitive wavelength regions. The facet properties of the primary optical Fresnel lens showed that the more rounded the Fresnel facets were, the lower the concentration of sunlight incident onto the CTJ cell. The increase in facet numbers showed an increase in scattering of the incident sunlight and chromatic aberrations. Chromatic aberration created by the refractive optics showed a variation in the amount of concentration on each individual subcell as well as the difference in intensity profiles across for the different subcells. Based on these results and the development of new multi-junction devices by industry, the performance of a four and six-junction device with the optical materials was investigated by simulations. The simulations showed that the careful integration of an additional subcell in a multi-junction device could rectify current mismatch between the subcells in the device. Based on the simulations, the best performing multi-junction cell was identified as the four-junction device that showed a cell and module efficiency under operation of 42.5 % and 35.5 %, respectively. Additionally, based on the performance results observed from the H-CPV module, the development of an HCPV module that would attempt to harness the incident tracked diffuse sunlight available to a concentrator photovoltaic (CPV) module for additional energy yield was undertaken. The part of the study comprised of measurements of the solar source, design of a prototype Hybrid High Concentrator Photovoltaic (HH-CPV) module. Results showed that power generation from the H-CPV system was highly dependent on the DNI levels and fluctuates greatly with variation in the DNI. The irradiance levels within the diffuse regions of the H-CPV module showed that the baseplate and vertical sides had an average irradiance range of 140-450 and 50-225 W.m-2, respectively. Irradiance topographic raster scans revealed that the baseplate and vertical sides had a relatively uniform intensity distribution and was identified as favourable sites for diffuse cell population. Simulations of various PV technologies showed the most suitable technology for the placement within the cavity of the HH-CPV module. The developed HH-CPV module was finalized with the utilization of CIS modules to harness the diffuse irradiance. During a 3 month power monitoring of the HH-CPV system, it was determined that the major power generation for the HH-CPV module come from the CPV component, while the CIS modules showed a minor power contribution. The total energy yield for the monitoring period was 45.99, 3.89 and 1.76 kW.h for the CPV, four-vertical sides and baseplate components, respectively. The increase in energy yield of the HH-CPV module when compared to the standard H-CPV module was determined to be 12.35 % for the monitoring period. The incorporation of the CIS modules into the H-CPV module to create the HH-CPV module did increase the energy yield of the module during high DNI conditions and did offset the almost zero power generation during low DNI conditions.

This research investigates the collection of concentrating solar energy and its transmission through optical fibres for use in high temperature applications such as lunar in-situ resource utilisation (ISRU) programmes, solar power generation and solar surgery. A prototype collector, known as the Fibre Optic Concentrating Utilisation System (FOCUS), has been developed and is capable of delivering high energy fluxes to a remote target. Salient performance results include flux concentrations approaching 1000 suns with an overall optical efficiency of 13%, measured from the inlet of the collector to the fibre outlet. The system comprises a novel solar concentrator designed to inject solar energy into a four metre long fibre optic cable for the transmission of light to the target. A nonimaging reflective lens in the form of a 600 mm diameter ring array concentrator was chosen for the collection of solar energy. Advantageous characteristics over the more common parabolic dish are its rearward focusing capacity and single stage reflection. The ring array comprises a nested set of paraboloidal elements constructed using composite material techniques to demonstrate a low-cost, effective fabrication process. At concentrator focus, a fibre optic cable of numerical aperture 0.37 is positioned to transport the highly concentrated energy away from the collector. The cable is treated to withstand UV exposure and high solar energy flux, and allows flexibility for target positioning. A computational analysis of the optical system was performed using ray tracing software, from which a predictive model of concentrator performance was developed to compare with experimental results. Performance testing of FOCUS was conducted using energy balance principles in conjunction with a flat plate calorimeter. Temperatures approaching 1500°C and flux levels in the region of 1800 suns were achieved before injection to the cable, demonstrating the optical system's suitability for use in high flux applications. During testing, peak temperatures exceeding 900°C were achieved at the remote target with a measured flux of 104 W/cm2 at the cable outlet. The predicted optical efficiency was 22%, indicating that further refinements to the ray trace model are necessary, specifically with regard to losses at the inlet to the cable. FOCUS was able to demonstrate its usefulness as a test bed for lunar in-situ resource utilisation technologies by successfully melting a lunar soil simulant. The system permits further terrestrial-based ISRU research, such as oxygen production from regolith and the fabrication of structural elements from lunar soil. / Thesis (M.Sc.Eng.)-University of KwaZulu-Natal, Durban, 2011.

Lanthanide (III) complexes are used extensively in solar conversion devices, such as Luminescent Solar Concentrators (LSCs) and Luminescent Down-Shifting (LDS) for their peculiar characteristics of narrow band emission, avoidance of re-absorption losses due to large Stokes shift and possibility of high photoluminescence quantum yield (PLQY). The study has looked into the synthesis of Ln (III) complexes of the general formula: [Ln(hfac)3DPEPO], where DPEPO = bis(2-(diphenylphosphino)phenyl)ether oxide, and hfac = hexafluoroacetylacetonate. The work presented in this thesis focuses on the synthesis, and subsequent photophysical characterisation of these Ln(III) complexes, plus characterisation and spectroscopic study of [Tb(pobz)3(hacim)2], (where Hpobz = phenoxybenzoic acid, and Hacim = acetylacetone imine), yielding results that open new design of functional Ln(III) systems. Spectroscopic study of Chromium dioxalate and analogous compounds has revealed that with the appropriate design, Cr(III)Ln(III) energy transfer can be achieved, while study of polyaromatic hydrocarbons (PAH) such as coronene, enable to explore a ligand with better absorption in the whole UV region. These results open attractive perspectives for light-conversion systems, such as LSC devices.

Thesis (M. S.)--Mechanical Engineering, Georgia Institute of Technology, 2008. / Committee Chair: Sheldon Jeter; Committee Member: Sam Shelton; Committee Member: Srinivas Garimella

Master of Engineering / Global warming and diminishing energy supplies are two major current concerns. Disposal of plastic wastes is also a major concern. The aim of this research is to address these three concerns by developing a solar powered process, using waste plastics as fuel to generate energy. Research into: i) solar concentrators for high temperature thermochemical processes, and ii) pyrolysis/gasification of waste plastics has been separately reported in the literature. In this study the aim was to bring these fields of research together to design a solar receiver-reactor suitable for the production of a synthesis gas, consisting of hydrogen, from waste plastics. To achieve this aim, studies of plastic decomposition behaviour using the thermal analysis method known as thermogravimetric analysis were conducted. Solar concentrators and their potential to be used for thermochemical processes were also studied. Firstly, the thermal decomposition behaviour of common plastics, namely low density polyethylene (LDPE), high density polyethylene (HDPE), polyethylene terephthalate (PET) and polyvinyl chloride (PET), were studied using thermogravimetry at heating rates of 5, 10, 20, 50 and 100 ºC/min. The kinetic parameters for the decomposition were determined from these experiments. Secondly, a simple solar receiver-reactor in which the plastic decomposition could be achieved was designed. The solar receiver-reactor designed was a quartz tube reactor which can be placed in the focus of a dish type parabolic concentrator capable of generating up to 3 kW in the focus of diameter 50 mm. The thermogravimetric analysis of plastic samples showed that LDPE, HDPE and PET have a single-step decomposition, whereas PVC has a two-step decomposition. The first step was related to the release of hydrogen chloride from the PVC and the second step was related to the release of hydrocarbon from the polymer backbone. If PVC is pretreated to release HCl it can be mixed with other plastics for a single step decomposition. It is likely that a single step plastic decomposition can be achieved in a directly irradiated solar receiver-reactor to generate useful gases consisting of hydrogen.

Master of Engineering / Global warming and diminishing energy supplies are two major current concerns. Disposal of plastic wastes is also a major concern. The aim of this research is to address these three concerns by developing a solar powered process, using waste plastics as fuel to generate energy. Research into: i) solar concentrators for high temperature thermochemical processes, and ii) pyrolysis/gasification of waste plastics has been separately reported in the literature. In this study the aim was to bring these fields of research together to design a solar receiver-reactor suitable for the production of a synthesis gas, consisting of hydrogen, from waste plastics. To achieve this aim, studies of plastic decomposition behaviour using the thermal analysis method known as thermogravimetric analysis were conducted. Solar concentrators and their potential to be used for thermochemical processes were also studied. Firstly, the thermal decomposition behaviour of common plastics, namely low density polyethylene (LDPE), high density polyethylene (HDPE), polyethylene terephthalate (PET) and polyvinyl chloride (PET), were studied using thermogravimetry at heating rates of 5, 10, 20, 50 and 100 ºC/min. The kinetic parameters for the decomposition were determined from these experiments. Secondly, a simple solar receiver-reactor in which the plastic decomposition could be achieved was designed. The solar receiver-reactor designed was a quartz tube reactor which can be placed in the focus of a dish type parabolic concentrator capable of generating up to 3 kW in the focus of diameter 50 mm. The thermogravimetric analysis of plastic samples showed that LDPE, HDPE and PET have a single-step decomposition, whereas PVC has a two-step decomposition. The first step was related to the release of hydrogen chloride from the PVC and the second step was related to the release of hydrocarbon from the polymer backbone. If PVC is pretreated to release HCl it can be mixed with other plastics for a single step decomposition. It is likely that a single step plastic decomposition can be achieved in a directly irradiated solar receiver-reactor to generate useful gases consisting of hydrogen.