Over the last 100 Years, the cyanidation process has been the most popular method for recovering gold from its ores. Despite this, there are still efforts to improve the efficiency of the process, particularly as ores become more difficult to treat. Many investigators have studied the cyanidation process, although a large proportion of these studies have obtained contradictory results. This thesis presents a kinetic and electrochemical study of the leaching of gold in cyanide solutions, and emphasis is placed on rationalising the conflicting results which have been published in the past.The leaching rate of gold was measured using a rotating electrochemical quartz crystal microbalance, an instrument which allows the simultaneous measurement of electrochemical data and mass changes at the solid-solution interface in real time. A proportion of this project was devoted to the on-going design of this instrument, and a number of modifications are discussed in detail. Initially, the leaching of gold in cyanide solutions was investigated under conditions of high purity. Under these conditions, it was found that the gold surface is blocked by a passive film, presumably AuCN. The presence of such a film results in the reaction being chemically controlled, and under typical cyanidation conditions (4 mM cyanide, pH 10.0), the rate of dissolution is very low. These kinetic results were supported by complimentary electrochemical studies, which showed that gold is passive in the potential region where cyanidation occurs.The second part of this thesis presents a study of the effect of system purity on the leaching of gold in cyanide solutions. Solution phase purity was investigated by adding controlled amounts of lead or silver to the leach solutions. It was found that in the presence of low concentrations of lead, the dissolution of gold in 20 mM cyanide solutions was oxygen ++ / diffusion controlled (as compared to chemical control for gold in the absence of lead). However, high concentrations of lead were found to be detrimental to the leaching process. It is believed that the role of lead is to modify the surface by cementation, hence reducing the effect of the passive film. Silver was also found to be effective at reducing passivation, and the role of silver believed to be similar to that of lead. It was found that unlike lead, high concentrations of silver are not detrimental to the dissolution of gold in cyanide solutions.Solid phase purity was also found to be important in the leaching of gold, and it was found that the leaching of a gold sample which contains 1 % silver is diffusion controlled. This finding is important from an industrial viewpoint, as most native gold contains some silver. Consequently, attempts were made to rationalise the leaching of gold/silver with current plant practice. Discussion on the effect of cyanide and oxygen concentrations, temperature and lead addition is presented.

The quantitative analysis of environmental and toxicological samples must be reliable, rapid, and in some cases field portable. In the United States, the employment of chemical weapons by rogue states and/or terrorist organizations is an ongoing concern. Nerve agent degradative products (methylphosphonic acid) as well as surrogates (glyphosate) must be detected at low quantities in various water matrices. Current methods involve tedious and time-consuming derivatizations for gas chromatography-mass spectrometry and liquid chromatography in tandem with mass spectrometry. Two solid phase extraction (SPE) techniques for the analysis of glyphosate and methylphosphonic acid are described with the utilization of isotopically enriched analytes for quantitation using atmospheric pressure chemical ionization-quadrupole-time of flight-mass spectrometry (APCI-Q-TOF-MS) that does not require derivatization. <br>The use of illicit drugs is also an increasing problem in the United States. Toxicological analysis of illicit drugs is important for death investigation as well as in the treatment of individuals who abuse and misuse drugs. This dissertation describes a newly developed analytical method for the simultaneous quantitative analysis of heroin, 6-acetylmorphine, morphine, cocaine, codeine, methadone, and fentanyl in synthetic urine. The resolution of an electrospray ionization-time of flight-mass spectrometer (ESI-TOF-MS) was utilized for simultaneous analysis of the drugs after extraction from urine using two newly developed SPE procedures. <br>The first SPE technique described in this dissertation is solid phase extraction-isotope dilution mass spectrometry (SPE-IDMS). It involves applying EPA Method 6800 in which a naturally occurring sample is pre-equilibrated with an isotopically enriched standard prior to SPE. The second extraction method, i-Spike, involves loading an isotopically enriched standard onto a SPE column independently from the naturally occurring sample. The sample and the spike are then co-eluted from the column enabling precise and accurate quantitation by molecular IDMS calculations. The SPE methods, in conjunction with IDMS, eliminate concerns of incomplete elution, matrix and sorbent effects, and MS drift. For accurate quantitation with IDMS, the isotopic contribution of all atoms in the target molecule must be statistically taken into account. This dissertation describes two newly developed sample preparation techniques for the analysis of environmental and toxicological samples as well as statistical probability analysis for accurate molecular IDMS. / Bayer School of Natural and Environmental Sciences / Chemistry and Biochemistry / PhD / Dissertation

Solid-phase syntheses of two 14-membered ring peptidomimetics were done to determine whether or not a beta-turn structure can facilitate macrocyclization. NMR methods, together with CD and QMD calculations, do not fully support this assumption. However, cyclizations of more ordered structures like those of compounds 2 were more efficient than those for highly strained ring systems like 1. A small library of 18-membered ring peptidomimetics that accommodate an extra amino acid residue was synthesized on resin. Their syntheses were not complicated by head-to-tail dimer impurity, unlike those for previously synthesized 14-membered systems. These larger macrocycles exhibit beta-turn structures as verified by NMR, CD and QMD techniques. Moreover, two compounds in this series (3a and 3g) were shown to have agonistic properties for TrkC in cell survival assays. Dimerization of monovalent mimics was achieved first by modifying the organic template so that monovalent mimics with requisite functional groups can be synthesized. Second, the monovalent units were dimerized using sequential nucleophilic substitutions on fluorescently labeled dichlorotriazine. Our rationale to make bivalent compounds out of monovalent ones was justified when compound 4 was shown to bind TrkA with a 20 nM affinity. Reactions of amino acids with NH4SCN under acylating conditions produced 2-thiohydantoins in which the nitrogen of the amino acid (N1) was acylated. This was proven by 2-D NMR which showed no cross-peak between the NH signal observed and the Cα±-H of the amino acid. When the compound was deacylated, a new NH signal appeared and the corresponding cross-peak with the Cα±-H was observed. Solution-phase syntheses of non-peptidic mimics were achieved by doing a double substitution on a dihalogenated nitrobenzene scaffold. Sonogashira and SNAr reactions were done to install the required side-chains to give the desired compounds. These non-peptidic compounds can be easily adapted to our DTAF-Inp dimerization protocol since the nitro groups can be easily reduced. Attempts to make a spirotetracyclic peptidomimetic with three side chain mimics were done by synthesizing the spirocyclic diketopiperazine precursor. The synthesis of the DKP was achieved by making the cyclic quaternary amino acid that was coupled to another amino acid via the HOAt-EDC method. This protocol gave dipeptides in high yields. These dipeptides were deprotected and cyclized to the DKP under mildly acidic conditions in toluene.

No description available.

Until recently, multiple SPME fibres could not be automatically evaluated in a single sequence without manual intervention. This drawback had been a critical issue until recently, particularly during the analysis of numerous on-site samples. Recently, GERSTEL® has developed and commercialized a Multi-Fibre Exchanger (MFX) system designed to overcome this drawback. In this research, a critical evaluation of the MFX performance in terms of storage stability and long term operation is presented. It was established in the course of our research that the MFX can operate continuously and precisely for over 200 extraction/injection cycles. However, when the effect of residence time of commercial fibres on the MFX tray was evaluated, the results have shown that amongst the evaluated fibre coatings, carboxen/polydimethylsiloxane (CAR/PDMS) was the only coating capable of efficient storage on the MFX tray for up to 24 hours after field sampling without suffering significant loss of analytes. Additionally, the MFX system capability for high-throughput analysis was demonstrated by the unattended desorption of multiple fibres after on-site sampling of two different systems, indoor air and biogenic emissions. Subsequently, a protocol based on a new, fast, reproducible, reusable and completely automated method that enables quick assessment of SPME coatings was developed. The protocol consists of an innovative in-vial standard generator containing vacuum pump oil doped with McReynolds probes and subsequently mixed with a polystyrene-divinylbenzene resin. According to our results, the protocol has proven to be a useful tool for the quick assessment of inter-fibre reproducibility prior to their application in on-site analysis. The implications of such protocols include, but are not limited to: time-saving, assurance of reliable and reproducible data, and a dependable guide for novice users of the technique. Finally, an innovative, reusable and readily deployable pen-like diffusive sampler for needle traps (PDS-NT) is proposed. Results have shown that the new PDS-NT is effective for air analysis of benzene, toluene, and o-xylene (BTX). In addition, no statistically significant effects of pen geometry on the uptake of analytes were found.

A method for the synthesis of a symmetrical fluorous tagged benzodithiol support has been developed through a seven-step synthetic pathway. The Wittig olefination and catalytic hydrogenation reactions were employed to attach two perfluoroalkyl chains in the o-positions of phthalaldehyde. These fluorous tags were used as soluble supports which facilitated the purification of the crude reaction mixtures using fluorous solid phase extraction (FSPE). A selective and high yielding dibromination reaction was developed to synthesize a fluorous tagged 1,2-dibromo aryl compound. A thorough study was carried out to demonstrate the ease of an aryl-sulfur bond formation with the 1,2-dibromo compound varying palladium catalysts and ligands. A new palladium catalyzed dithiolation reaction is reported to synthesize a surrogated dithiol, which was exploited as a precursor for the synthesis of hitherto inaccessible symmetrical fluorous tagged benzodithiol support. The utility of the benzodithiol was explored by the synthesis of benzodithianes with two aldehydes. The lithiated dithiane generated was further used to form a C-C bond employing the umpolung reaction. The ring-closing metathesis reaction using Grubbs II catalyst was performed to construct 5-membered and 6-membered spiro-ring systems. Several approaches were made to form a C-C bond with lithiated dithianes using various nitrogen containing electrophiles leading to N-heterocycles. / October 2008

Aluminum and its alloys are used in many aspects of modern life, from soda cans and household foil to the automobiles and aircraft in which we travel. Aluminum alloy systems are characterized by good workability that enables these alloys to be economically rolled, extruded, or forged into useful shapes. Mechanical properties such as strength are altered significantly with cold working, annealing, precipitation-hardening, and/or heat-treatments. Heat-treatable aluminum alloys contain one or more soluble constituents such as copper, lithium, magnesium, silicon and zinc that individually, or with other elements, can form phases that strengthen the alloy. Microstructure development is highly dependent on all of the processing steps the alloy experiences. Ultimately, the macroscopic properties of the alloy depend strongly on the microstructure. Therefore, a quantitative understanding of the microstructural changes that occur during thermal and mechanical processing is fundamental to predicting alloy properties. In particular, the microstructure becomes more homogeneous and secondary phases are dissolved during thermal treatments. Robust physical models for the kinetics of particle dissolution are necessary to predict the most efficient thermal treatment. A general dissolution model for multi-component alloys has been developed using the front-tracking method to study the dissolution of precipitates in an aluminum alloy matrix. This technique is applicable to any alloy system, provided thermodynamic and diffusion data are available. Treatment of the precipitate interface is explored using two techniques: the immersed-boundary method and a new technique, termed here the sharp-interface method. The sharp-interface technique is based on a variation of the ghost fluid method and eliminates the need for corrective source terms in the characteristic equations. In addition, the sharp-interface method is shown to predict the dissolution behavior of precipitates in aluminum alloys when compared with published experimental results. The influence of inter-particle spacing is examined and shown to have a significant effect on dissolution kinetics. Finally, the impact of multiple particles of various sizes interacting in an aluminum matrix is investigated. It is shown that smaller particles dissolve faster, as expected, but influence the dissolution of larger particles through soft-impingement, even after the smaller particles have disappeared.

In this study, a LC/MS/MS method for the determination of ampicillin antibiotic in fish muscle tissue was developed and accredited according to Commission Decision 2002/657/EC. The metabolism of ampicillin in tilapia was them studied in serum, liver and muscle. The homogenized fish tissue was first extracted with MeOH-H2O(4:1), C18 sorbent was added to remove lipids and impurities, the extract was then evaporated to dryness with a steam of nitrogen gas at 38 ¢XC. The residue was redissolved with H2O, filtered and analyzed by LC/MS/MS equipped with an Agilient HC-C18(5£gm, 150mm ¡Ñ4.6mm), the mobile phase A was 10mM ammonium acetate containing 0.1% formic acid, while the mobile phase B was methanol. The determination of ampicillin was performed with electrospray ionization-tandem mass spectrometry in positive mode using multiple reation monitoring(MRM) for detection. Average recoveries were 81¡V86%, the limit of detection was 6.00 £gg kg-1¡Adecision limit(CC£\) of ampicillin in fish muscle sample was 63.65 ¡Ó 7.99 £gg kg-1. In the metabolism study, the oral administered dose to talipia was 20 mg/kg¡DBW. The maximum concentration of ampicillin in each tissues was obserned at 0.5 hour after oral administration, the maximum concentration in serum, liver and muscle was 27.53 mg L-1, 66.75 mg kg-1 and 1.33 mg kg-1, respectively. The concentration of ampicillin in muscle was 0.04 mg kg-1 24 hours after oral administration, which is lower than the 0.05 mg kg-1 MRL value of European Union resolutions. No residual ampicillin was detected in tilapia 48 hours after oral treatment, which conformed to the drug regulations for aquaculture ainmals in Taiwan.

Solid-phase syntheses of two 14-membered ring peptidomimetics were done to determine whether or not a beta-turn structure can facilitate macrocyclization. NMR methods, together with CD and QMD calculations, do not fully support this assumption. However, cyclizations of more ordered structures like those of compounds 2 were more efficient than those for highly strained ring systems like 1. A small library of 18-membered ring peptidomimetics that accommodate an extra amino acid residue was synthesized on resin. Their syntheses were not complicated by head-to-tail dimer impurity, unlike those for previously synthesized 14-membered systems. These larger macrocycles exhibit beta-turn structures as verified by NMR, CD and QMD techniques. Moreover, two compounds in this series (3a and 3g) were shown to have agonistic properties for TrkC in cell survival assays. Dimerization of monovalent mimics was achieved first by modifying the organic template so that monovalent mimics with requisite functional groups can be synthesized. Second, the monovalent units were dimerized using sequential nucleophilic substitutions on fluorescently labeled dichlorotriazine. Our rationale to make bivalent compounds out of monovalent ones was justified when compound 4 was shown to bind TrkA with a 20 nM affinity. Reactions of amino acids with NH4SCN under acylating conditions produced 2-thiohydantoins in which the nitrogen of the amino acid (N1) was acylated. This was proven by 2-D NMR which showed no cross-peak between the NH signal observed and the Cα±-H of the amino acid. When the compound was deacylated, a new NH signal appeared and the corresponding cross-peak with the Cα±-H was observed. Solution-phase syntheses of non-peptidic mimics were achieved by doing a double substitution on a dihalogenated nitrobenzene scaffold. Sonogashira and SNAr reactions were done to install the required side-chains to give the desired compounds. These non-peptidic compounds can be easily adapted to our DTAF-Inp dimerization protocol since the nitro groups can be easily reduced. Attempts to make a spirotetracyclic peptidomimetic with three side chain mimics were done by synthesizing the spirocyclic diketopiperazine precursor. The synthesis of the DKP was achieved by making the cyclic quaternary amino acid that was coupled to another amino acid via the HOAt-EDC method. This protocol gave dipeptides in high yields. These dipeptides were deprotected and cyclized to the DKP under mildly acidic conditions in toluene.

No description available.