This thesis describes an experimental investigation into ignition systems, their effects on the combustion process, and how the discharge is affected by the prevailing pressure, temperature and flow. The work is divided into four main areas, a comprehensive literature review, engine testing for ignition system suitability, non-flow rig testing (including erosion) and flow rig testing. The literature review concluded that the most practical ignition system for lean burn gas engines will continue to be based on the spark plug, but in the medium to long term, laser ignition may become viable. The measurement of the HT voltage and current is not straightforward, and appropriate methods have been identified. Capacitive and inductive ignition system types were compared in lean and diluted conditions on a single cylinder research engine of modern design at different engine loads and speeds. It was found that the most beneficial ignition system was an inductive ignition system, although that for some conditions, capacitive systems induced better engine performance with a fraction of the stored energy of the inductive alternative. Non flow tests showed that the early part of the spark discharge is sensitive to pressure and temperature effects, and as a consequence, the latter stages of the discharge are also affected. A correlation has been developed, for use with conventional nickel electrode spark plugs, to predict breakdown voltage as a function of pressure, temperature and gap. Experiments were carried out at elevated pressures in a stream of flowing air with capacitive and inductive ignition systems. Different electrode designs and orientations were also compared. It was shown that when exposed to a flow field, the discharge can be stretched which results in a shortened spark duration; in some cases the electrode can shield the discharge from flow field effects. This work showed that flow through the spark gap is a hindrance to the spark process, especially for longer duration systems. However for flame kernel growth, the literature review identified that flow is beneficial, serving to convect the kernel away from the electrodes, reducing the heat transfer from the flame. Analysis of the glow voltage history in the pressurised flow rig has been used to develop a correlation relating the voltage, current, flow velocity, pressure and time. This correlation was used to analyse the velocity records from the spark plug in a firing engine. The predicted velocities and turbulence intensity were in agreement with independent measurements.

This research presents the first use of side-polished Panda fiber in the fabrication of slab-coupled optical sensors (SCOS). It is determined that the Panda SCOS provides a sensor that is comparable to the D-fiber SCOS in cases of electric field sensing. It exhibits greater power transfer and higher bandwidth than a typical D-SCOS. The Panda SCOS is also less costly and easier to splice than the D-fiber alternative. This comes at a cost of slightly decreased sensitivity and a more fragile fabrication process. This research also demonstrates the use of the Panda-SCOS as means of voltage characterization across both the spark gap of an ignition coil circuit along with the spark gap of an automobile. This paper demonstrates the use of a Panda SCOS to measure the voltages and time delays across the spark gaps at different stages of a Marx generator setup .

Face aux normes actuelles et futures, de plus en plus drastiques, concernant les émissions de polluants, les constructeurs automobiles cherchent en permanence à améliorer l'efficacité des moteurs à allumage commandé. Une des solutions les plus efficaces et applicables pour diminuer la quantité de polluants émis dans les gaz d’échappement (HC, CO, NOx) et réduire la consommation de carburant, est d’utiliser un mélange très pauvre (richesse du mélange inférieure à 0,6). Toutefois, ce concept de fonctionnement est limité par les systèmes d'allumage classiques qui ne peuvent pas garantir un allumage du mélange air / combustible dans de bonnes conditions, de manière à assurer une combustion complète, rapide et reproductible.Le sujet de cette thèse consiste en l'élaboration d'un nouveau système d'allumage basé sur une bougie d’allumage double, qui peut produire deux d'étincelles quasi-simultanées, dont la longueur cumulée est plusieurs fois plus élevée que celle d’étincelles produites par une bougie d'allumage classique. Pour valider ce système d'allumage, trois différents types d'analyses ont été réalisés: une analyse des paramètres électriques des décharges, un diagnostic du plasma par spectroscopie optique d'émission, et des essais in situ du système d'allumage sur deux moteurs à combustion interne avec analyse des gaz d'échappement et détermination des performances des moteurs.Ces tests ont révélé que l'utilisation du système d’allumage à double étincelle peut assurer une meilleure stabilité dans le fonctionnement du moteur (en particulier dans les conditions d'allumage difficiles, en utilisant des mélanges très pauvres) ; des performances accrues du moteur pour une même quantité de carburant consommé ; et une diminution de la quantité d’hydrocarbures imbrûlés et de monoxyde de carbone dans les gaz d'échappement, mais avec une plus grande émission d'oxydes d'azote par rapport à un système d'allumage classique. / Faced with the current and future more and more drastic standards for pollutant emissions, the car manufacturers are permanently trying to improve the efficiency of spark ignition engines. One of the most effective applicable solutions for reducing the quantity of pollutant emissions (HC, CO, NOx) from the exhaust gases and also to reduce the fuel consumption is to operate with very lean mixture (equivalent ratio lower than 0.6). However, this operation concept is limited by the actual ignition systems that cannot assure an air/fuel mixture ignition in good conditions, in order to assure a complete, fast and repeatable combustion. The subject of this thesis consists into developing of a new ignition system based on a double spark plug, which can produce two quasi-simultaneous spark discharges with cumulated length few times higher than the sparks produced by a conventional spark plug. For ignition system validation, three different types of analysis have been considered: the analysis of the discharges electrical parameters, the plasma diagnosis using optical emission spectroscopy methods and the tests of the ignition system on two internal combustion engines with the exhaust gases analysis and engine performances determination. The tests revealed that the utilization of the double spark ignition system can assure a better stability in engine operation (especially in difficult ignition conditions such using very lean mixtures), increased engine performances for the same amount of consumed fuel and it can provide a diminution of the unburned hydrocarbons and carbon monoxide quantities from the exhaust gases, but with an increased quantity of nitrogen oxides, compared with a conventional ignition system.

This master thesis deals with ignition systems which are used in cars vehicles with gas engines and also with setting of the best moment of ignition of gasoline-air mixture in cylinders of engine. Ways of gas injection at diesel engines and their control systems are also described in this thesis. Next chapter deals with control unit and describes main actions which are necessary for today’s motor vehicles. As illustration is used example of succession of actions which are necessary for calculation and setting regular value of pre-ignition. At the end is shown animation, which can be used for practice lessons in a subject Automobile Electric and Electronic Systems as a example. It will simplify understanding of described activities which are all accomplished by central control unit. For purposes of laboratory lessons is in this thesis also discussed measuring of engine performance with changes of parameter of central control unit.