Diploma thesis deals with design and assessment of a ceiling of a library in Ostrava. The solved beamed ceiling is above the third floor. Static analysis of the structure was calculated by Scia Engineer 20 software. Two variants of ceiling was calculated. Thesis then focuses on prestressed ceiling.

The subject of this diploma thesis is structural design of a car showroom building in Olomouc. The layout dimensions are 16 x 37 m, the roof is designed as a 5° slope half span roof with cantilever hanging of 6 m. Roof layout dimensions are therefore 22 x 37 m. The object is designed as a two – storey building with two levels of second floor. Maximum height of the structure is about 9,0 m. The design is based on a study of two materiál variants – timber and steel structure. More suitable variant was chosen and following drawings, structural design report and technical report were processed. Main structural system is designed as a one rigid corner column – girder connection, 6 m axis dimensions. Main structural material is a glued laminated timber, completed with coniferous timber and steel elements. The roofing is supported by rafters which are connected to the main roof truss. Bearing element of floors is a Novatop Element structural systém. The spatial rigidity of structure is ensured by steel stiffeners. Structural analysis was carried out by finite element method in software Scia Engineer 21, where the design of the basic elements for ultimate limit state and serviceability limit state was made. Connection design was processed manuály and with software Idea Statica and Hilti Engineering Suite.

The topic of this thesis is design and evaluation of the bridge structure. Three variants of bridging were created, among which the variant with prestressed girder deck and seven spans was chosen to detail processing. The bridge construction is built on sliding steel girder in several stages. Construction is evaluated considering the ultimate serviceability state and ultimate limit state. Emphasis is also on evaluation of construction stages. The calculation of load effects and analysis of building in stages was done in Scia Engineer 19.1 software. Design and evaluation were done according to currently valid European standards.

This Master's thesis reflects the theory of American political philosopher S. Wolin. The work introduces the reader to interpretations of S. Wolin's term inverted totalitarianism and confronts it with the common and mainstream approaches to totalitarianism. It is concerned about S. Wolin's reflection on contemporary western liberal democracy as managed democracy. The text pays attention to work of G. Agamben who takes a similar critique on the form of Euro-Atlantic democracy; for instance the thesis deals with his view of state of exception in which the author sees connections on inverted totalitarianism. Powered by TCPDF (www.tcpdf.org)

Title: Group exercise with elements of the method Pilates in individuals with ankylosing spondylitis - comparisons with the control group Objective: Find impact of group therapy with engaging Pilates method to movability of axial system, functional status, activity of disease and total health status of individuals with ankylosing spondylitis. Compare this method with compensation group motion program in individuals with ankylosing spondylitis. Methods: 26 individuals with ankylosing spondylitis of average age (38,25 ± 9,18) attending Institute of Rheumatology in Prague were chosen. Probands were split into two groups: experimental group, which were doing motion program with elements of Pilates (n=13), and control group, which were attending compensation group motion program in individuals with ankylosing spondylitis. It was empirical quantitative research, exactly comparative quasiexperiment, where was compared individual groups in between (inter-group) and, moreover, influence of individual motion programs (intra-group). Data gathering was executed twice - at the beginning of quasiexperiment (pre-test) and at the end (3 months after; post-test). Those parameters were examined: Bath Ankylosing Spondylitis Metrology Index for axial system region and expansion of chest, Bath Ankylosing Spondylitis...

The thesis deals with evaluation of the environmental thermal state in closed rooms with people inside the room. The achievement of thermal comfort is related to thermal balance of human body. People are producing heat during their work, which has to be carried away from the body to surrounding area by radiation, convection, conduction, respiration and evaporation. The intensity of heat removal is influenced by environmental parameters, especially by air temperature, mean radiant temperature, air velocity and humidity. Personal factors as energy expenditure of human body and clothing resistance are influencing the intensity of heat removal as well. People are able to influence the thermal comfort by their behaviour in given environment, appropriate clothing and regulation of basic environmental parameters. CSN EN ISO 7730 standard states that environmental parameters should be estimated or measured. The operative temperature is than evaluated from collected data. This operative temperature is defined as the temperature of black enclosed area where the human body will be by convection and radiation sharing the same amount of heat as in real inconsistent environment. Nowadays on the market there is no cheap solution for sensor which is able to evaluate the operating temperature and could be used in buildings. There are a lot of professional sensors which have very high accuracy, but are very expensive. Therefore are mainly used only for research or for single and exceptional measurement of environmental thermal state in rooms. The thesis is therefore focused on proposal of suitable (compact) operative temperature sensor assembled according to valid regulations and standards. Emphasis is placed mainly on the sensor price together with guarantee of sufficient accuracy. The proposed sensor is providing information to control system which is than able to adjust the parameters of environment using appropriate way based on relevant requirements. Here is some space for energy savings due to possible continuous measurement and evaluation of environmental thermal state in different rooms. Therefore, during continuous measurement no unnecessary rooms overheating in winter as well as unreasonable cooling in summer should occur. This research and solution is than reflected in reduction of energy consumption used for building operation and subsequently reduction of the pollutants production. This issue is being watched with increasing interest. Another advantage is that whole system is able to work autonomously without human intervention. People no longer have to continuously adjust air temperature because the control system is able to evaluate the most appropriate adjustments based on objective data obtained from the sensor. The thesis includes subsequent verification of proposed sensor as well as the definition of sensor technical parameters including analysis of measurement uncertainties.

The contents of this thesis are the introduction to mesh grids, the method of dispatch control of these grids and the description of technology used in mesh grids distribution nodes in the city of Brno. This thesis also describes low voltage switchgears used in these types of grids. The development of dispatch control in ECD company is also mentioned. The development describes the grid dispatch control methods prior to implementing the OMS system and the changes which followed after the implementation. The process improvements of the new system resulting from this thesis can be found in this thesis as well. The improvements are incorporated in the OMS system and are used for more efficient dispatch control of the low voltage mesh grids. There is a more detailed analysis of the mesh grid Brno – Bohunice in the practical part of this thesis. The practical part contains analyses of mesh grids stabilized conditions measurements and analyses of mesh grids fault conditions measurements. The analyses assess the power load in transformers, minimal and maximal phase current and maximal power load at the time they were observed. The analysis of the measured data is accompanied by the assessment of differences in current phase measurements and differences in voltage phase and combined measurements. The result, based on the analysis and collection of the data, is a proposition of adding switchgears for the support of the dispatch control of the mesh grid Brno – Bohunice. In the summary of the thesis there is a comparison of the result of the factual and theoretical analysis. An experimental model of the mesh grid Brno – Bohunice was created in PS CAD software as a part of the theoretical analysis.

Changes in the marital status in the age group from 15 to 59 years in the Czech Republic after 1930 Abstract The aim of this thesis is to analyze the changes in population structure according to the individual marital statuses. For this analysis sex-specific and age-specific nuptuality rates and multistate life tables were use, in order to be able to describe transitions between the individual marital statuses. In the first part of this thesis the data sources and the methods of creating the transversal increment- decrement life tables were described. Following chapters deal with the historical development of the Czech Republic population since the year 1930 and the trends of nuptuality, divorce and mortality. Second part is dedicated to the analysis of the transitions between the individual marital statuses. The findings of this thesis conclude that people in the individual marital states tend to react similarly to the historical events in Czech Republic, unless some events are purposefully aiming to influence only a part of the population. Key words: nuptuality rate, divorce rate, mortality rate, marital status, multistate demography, transversal increment-decrement life tables, Czech Republic

The main objective thesis was consider resistence of grow grain as elementary qualitative parameter food wheat by selection variety winter wheat. The test was create in vegetational period of years 2014/2015 on the plot of Faculty of Agriculture, University of South Bohemia in České Budějovice. In total was for test select 9 variety winter wheat. All variety had show high value number fall, high resistence against grow grain, which ranged 376 to 512 s. In evaluation observe variety suitability in terms of baking, we can say elite (E) inbreads reached the highest average number values fall (479 s). Quality (A) varietes showed value (453 s) and bread (B) varieties reached the lowest value (435 s). The partial objective was evaluation and other indicators (Zeleny test, The content of N-substances and density). Value of Zeleny test ranged 35 to 53 ml., from it averaged of all varietes 49,4 ml. The content of N-substances varied for each variety in 14,23 % - 16,52 %. Most of the studied varieties meet the standard set limit density (760 g/l-1). Ranged from 747 to 819 g/l-1. During the vegetation was also evaluated the health status of vegetation and there has been a determination of ears per square meter. After harvesting, they were also evaluated as further yield elements (number of grains per spike and HTZ). The experiment was evaluated by a high level of quality indicators, where individual varieties also showed high rebenues. This may be primarily affected by higher than average temperatures during the period of years 2014/2015, agrotechnics, but but also the level of nutrition and fertilization of crops.

The topic of my dissertation is "Organization and management of production in selected enterprise". The main goal of this dissertation is mapping of selected enterprise in one year period and obtain sufficient amount of information for future analysis and suggest possible improvements. The identification data, characteristic, products and services and production planning of selected enterprise are provided in introduction of practical part of this dissertation. Analysis of present state with mapping of present state for individually semi-finished products is introduced in the next part of dissertation. For analysis of present state was calculated VA index and for each semi-finished product was created diagram of material movement in next chapter. The goal of analyses and diagram is the finding of narrow spaces in the material flow. The target map of future state was created in the next part. This map is based on present map. The future map presents critical factors that need to be improved. Finally it defines a new VA index, which should be approach to the current state. The penultimate section includes recommendations methods and elements of lean production to the new production hall which the company wants to build. Among the recommended methods are mainly the 5S method, visualization, standardization, SMED and Bottleneck. The last chapter contains a number of measures. For example employee motivation, continuous improvement, personal responsibility, introduction of EDI and ergonomics which would lead to the improvement of the business this enterprise.