This dissertation presents the results of experimental and computational investigations on the behavior of steel simple beam end framing connections subjected to fire. While significant progress has been made in understanding the overall structural response of steel buildings subject to fire, the behavior of connections under fire conditions is not well understood. Connections are critical elements for maintaining the integrity of a structure during a fire. Fire can cause large force and deformation demands on connections during both the heating and cooling stages, while reducing connection strength and stiffness. Of particular importance are simple beam end framing connections. These are the most common type of connection found in steel buildings and are used at beam-to-girder and girder-to-column connections in the gravity load resisting system of a building. This dissertation focuses on one particular type of beam end connection: the single plate connection, also known as a shear tab vii connection. This connection is very commonly used in U.S. building construction practice. In this study, material properties of ASTM A992 structural steel at elevated temperatures up to 900°C were investigated by steady state tension coupon tests. Experimental studies on the connection subassemblies at elevated temperatures were conducted to understand and characterize the connection strength and deformation capacities, and to validate predictions of connection capacity developed by computational and design models. In the computational studies, a three-dimensional finite element connection model was developed incorporating contact, geometric and material nonlinearity temperature dependent material properties. The accuracy and limitations of this model were evaluated by comparison with experimental data developed in this research as well as data available in the literature. The computational studies investigated the typical behavior of the connection during heating and cooling phases of fires as well as the connection force and deformation demands. The finite element model was further used to study and understand the effects of several key building design parameters and connection details. Based on the test and analysis results, some important finding and conclusions are drawn, and future work for simple shear connection performance in fire are discussed. / text

No description available.

Master of Science / Department of Architectural Engineering / Kimberly W. Kramer / In structural steel connection design, simple shear connections are one of the most common connection types utilized. The industry, especially from the side of the engineer, tends to lean toward using Double Clip Angle Connections as the default standard for simple shear connections. A double clip angle connection is a connection consisting of two angles transferring the shear forces from one member to the next either through bolts or welds. The design of Double Clip Angle Connections is efficient and the connections themselves are easy to fabricate. However, benefits to utilizing other types of shear connections exist. Many of these benefits are seen in the fabrication shop or during erection and construction. This is especially true of single shear plate or shear tab connections when applied to open structure design. Shear tab connections consist of a single plate that transfers the shear forces from one member to the next with bolts or with welds. The design of shear tab connections can be a more involved process than the design of double clip angles. Sometimes the shear plate or shear tab has to be longer than is typical. This is called an extended shear plate connection. These extended shear plates can bring other variables into the design that typically don’t occur with Double Clip Angle Connections such as bending of the plate or the need for multiple bolt columns. However, with proper planning and detailing, the benefits and savings experienced in the fabrication or construction phase may outweigh what can be seen as a more laborious design task. The purpose of this report is to identify the possible benefits achieved in using each of these connections, highlight the differences in the design approach for each, and use a study model to compare the outcome of using one connection over another in the design of a typical open structure. Double clip angles are typically the most efficient approach when speed of design and simplicity of fabrication are the desired outcomes. However, shear plate or shear tab connections have the potential to provide safer erection alternatives and materials savings if used in appropriate ways and with the right applications.

No description available.

As typically designed, the beam-column-brace connections of buckling-restrained braced steel frames have undesirable failure modes that compromise the integrity and performance of the frames and are costly to repair. To decrease the time and resources needed to repair the frames following an earthquake, a new connection design was developed that attempts to confine yielding to replaceable frame components. The design incorporates a gap in the beam beyond the edge of the beam-gusset weld that acts as a hinge and reduces moment forces transferred to the connection; it is bridged by splice plates that are bolted to the beam top flanges. The splice plates and buckling-restrained braces are the only frame components that are expected to yield. To investigate the performance of the proposed connection design, a prototype bay was designed and two test specimens were fabricated and tested. Each specimen represented a corner of the prototype braced bay and consisted of a beam, column, gusset plate, brace core extension assembly, splice plates, and lateral bracing angles. Both standard design procedures and newly developed criteria were used to design the connection. In preparation for testing, a method was developed for estimating the hysteretic response of a buckling-restrained brace. By using this method to program an actuator, the specimens could be tested without using actual braces, resulting in a significant reduction in testing cost. Testing was conducted using two 600 kip actuators; the first followed a static loading protocol with a maximum design drift of 6.5%, and the second replicated the prototype BRB's response. The tests yielded promising results: both specimens withstood the maximum displacements and avoided yielding in the beams, columns, and gusset plates; yielding did occur in the splice plates and BRB core extension assembly, as anticipated. Possible limitations in the design may arise under the presence of increased shear loads, concrete floor slabs, or out-of-plane loading. Additional testing is recommended.

The difficulty in developing bolted connection designs lies in the limitations in existing methods to characterize their strength and typically nonlinear response due to the complex interaction of the bolts and structural components. Yet it is necessary for the engineer to be able to determine the three main connection response characteristics: stiffness, strength, and ductility to account for their influence on the overall structural response behavior. The need for better connection response characterization becomes even more crucial in a performance based design approach or when designing partially-restrained moment frames. Several welded moment resisting frame connections were found to have serious failures following the 1994 Northridge earthquake leading to more interest and research on bolted connections as an alternative. In this study a refined three dimensional nonlinear finite element modeling approach to accurately simulate the response of bolted connections is presented. Sensitivity studies of modeling parameters are also performed. A nonlinear response dataset of over 400 connection cases is generated using this approach with a parametric bolted angle connection model. The use of a parametric Richard-Abbott type function and a neural network, calibrated using the response dataset, as practical tool to model the nonlinear stiffness response of bolted connections under monotonic loading is demonstrated and assessed. Failure criteria that can be practically used in conjunction with the refined three dimensional finite element models without any additional modeling requirements are developed. The stress modified critical strain (SMCS) criterion based on the void growth and coalescence mechanism initiating ductile fracture in steel is used for determining failure in the connection member. The bolt failure criterion developed is a mechanics based model using the elliptical interaction of the tensile and shear capacity envelope. The failure criteria and bolted angle response dataset is combined to assess in detail the impact of geometry and topography of the bolted angle connections on the following response characteristics: strength, initial stiffness, plastic stiffness, and absolute ductility or the displacement capacity. Finally, using the dataset of bolted angle connection response, along with their capacities and failure modes determined using the developed failure criteria, the prying strength models in the AISC LRFD Specifications, Eurocode, and a hybrid model are assessed and found to be very conservative for some cases. Based on these results a modified Eurocode and hybrid prying strength model is proposed which greatly improves the prying strength prediction. These prying models are assessed and verified using experimental data found in literature.