Three--dimensional mapping has many applications including robot navigation, medical diagnosis and industrial inspection. However, many applications remain unfilled due to the large size and complex nature of typical 3--D mapping systems. The use of fiber optics allows the miniaturization and simplification of many optical systems. This research used a fiber optic coupler to project a fringe pattern onto an object to be profiled. The two outputs fibers of the coupler were brought close together to form the pinholes of a Young's Double Pinhole Interferometer. This provides the advantages of this simple interferometer without the disadvantage of power loss by the customary method of spatially filtering a collimated laser beam with a pair of pinholes. The shape of the object is determined by analyzing the fringe pattern. The system developed has a resolution of 0.1mm and a measurement error less than 1.5\% of the object's depth. The use of fiber optics provides many advantages including: remote location of the laser source (which also means remote location of heat sources, a critical requirement for many applications); easy accommodation of several laser sources, including gas lasers and high--power, low--cost fiber pigtailed laser diodes; and variation of source wavelength without disturbing the pinholes. The principal advantages of this mapping system over existing methods are its small size, minimum number of critically aligned components, and remote location of the laser sources. / Ph. D.

No description available.

Manufacturing of precise structures in MEMS, semiconductors, optics and other fields requires high standards in manufacturing and quality control. Appropriate surface topography measurement technologies should therefore deliver nm accuracy in the axial dimension under typical industrial conditions. This work shows the characterization of a dispersion-encoded low-coherence interferometer for the purpose of fast and robust surface topography measurements. The key component of the interferometer is an element with known dispersion. This dispersive element delivers a controlled phase variation in relation to the surface height variation which can be detected in the spectral domain. A laboratory setup equipped with a broadband light source (200 - 1100 nm) was established. Experiments have been carried out on a silicon-based standard with height steps of 100 nm under different thermal conditions such as 293.15 K and 303.15 K. Additionally, the stability of the setup was studied over periods of 5 hours (with constant temperature) and 15 hours (with linear increasing temperature). The analyzed data showed that a height measurement of 97.99 ± 4:9nm for 293.15 K and of 101.43 ± 3:3nm for 303.15 K was possible. The time-resolved measurements revealed that the developed setup is highly stable against small thermal uctuations and shows a linear behaviour under increasing thermal load. Calibration data for the mathmatical corrections under different thermal conditions was obtained.

This work introduces a modified low-coherence interferometry approach for nanometer surface-profilometry. The key component of the interferometer is an element with known dispersion which defines the measurement range as well as the resolution. This dispersive element delivers a controlled phase variation which can be detected in the spectral domain and used to reconstruct height differences on a sample. In the chosen setup, both axial resolution and measurement range are tunable by the choice of the dispersive element. The basic working principle was demonstrated by a laboratory setup equipped with a supercontinuum light source (Δλ = 400 ̶ 1700 nm). Initial experiments were carried out to characterize steps of 101 nm on a silicon height standard. The results showed that the system delivers an accuracy of about 11.8 nm. These measurements also served as a calibration for the second set of measurements. The second experiment consisted of the measurement of the bevel of a silicon wafer. The modified low-coherence interferometer could be utilized to reproduce the slope on the edge within the previously estimated accuracy. The main advantage of the proposed measurement approach is the possibility to collect data without the need for mechanically moving parts.

Within this work a scan-free, low-coherence interferometry approach for surface profilometry with nm-precision is presented. The basic setup consist of a Michelson-type interferometer which is powered by a supercontinuum light-source (Δλ = 400 - 1700 nm). The introduction of an element with known dispersion delivers a controlled phase variation which can be detected in the spectral domain and used to reconstruct height differences on a sample. In order to enable scan-free measurements, the interference signal is spectrally decomposed with a grating and imaged onto a two-dimensional detector. One dimension of this detector records spectral, and therefore height information, while the other dimension stores the spatial position of the corresponding height values. In experiments on a height standard, it could be shown that the setup is capable of recording multiple height steps of 101 nm over a range of 500 µm with an accuracy of about 11.5 nm. Further experiments on conductive paths of a micro-electro-mechanical systems (MEMS) pressure sensor demonstrated that the approach is also suitable to precisely characterize nanometer-sized structures on production-relevant components. The main advantage of the proposed measurement approach is the possibility to collect precise height information over a line on a surface without the need for scanning. This feature makes it interesting for a production-accompanying metrology.