Spelling suggestions: "subject:"thermophoresis sampling""
1 |
Investigating Soot Morphology in Counterflow Flames at Elevated PressuresAmin, Hafiz 01 1900 (has links)
Practical combustion devices such as gas turbines and diesel engines operate at high pressures to increase their efficiency. Pressure significantly increases the overall soot yield. Morphology of these ultra-fine particles determines their airborne lifetime and their interaction with the human respiratory system. Therefore, investigating soot morphology at high pressure is of practical relevance.
In this work, a novel experimental setup has been designed and built to study the soot morphology at elevated pressures. The experimental setup consists of a pressure vessel, which can provide optical access from 10° to 165° for multi-angle light scattering, and a counterflow burner which produces laminar flames at elevated pressures.
In the first part of the study, N2-diluted ethylene/air and ethane air counterflow
flames are stabilized from 2 to 5 atm. Two-angle light scattering and extinction technique have been used to study the effects of pressure on soot parameters. Path averaged soot volume fraction is found to be very sensitive to pressure and increased significantly from 2 to 5 atm. Primary particle size and aggregate size also increased with pressure.
Multi-angle light scattering is also performed and flames are investigated from 3
to 5 atm. Scattering to absorption ratio is calculated from multi-angle light scattering and extinction data. Scattering to absorption ratio increased with pressure whereas the number of primary particles in an aggregate decreased with increasing pressure.
In the next part of the study, Thermophoretic Sampling of soot is performed, in
counterflow flames from 3 to 10 atm, followed by transmission electron microscopy.
Mean primary particle size increased with pressure and these trends are consistent withour light scattering measurements. Fractal properties of soot aggregates are found to be insensitive to pressure.
2D diffused light line of sight attenuation (LOSA) and Laser Induced
Incandescence (LII) are used to measure local soot volume fraction from 2 to 10 atm.
Local soot volume fraction increased with pressure and soot concentration profiles showed good agreements when measured by both techniques. Experimental data obtained in this work is very helpful for the modelers for validating their codes and predicting the soot formation in pressurized flames.
|
2 |
Fundamental Studies of Soot Formation and Diagnostic Development in Nonpremixed Combustion EnvironmentsBennett, Anthony 06 1900 (has links)
Abstract: Soot from combustion emissions has a negative impact on human health and the environment. Understanding and controlling soot formation is desirable to reduce this negative impact, especially as energy demands continue to increase. In this work, a range of fundamental combustion experiments are performed to better understand the soot formation process, and to develop diagnostics for measuring soot properties.
First, studies on the effects of doping the flame with different polycyclic aromatic hydrocarbons (PAHs) was performed to investigate soot nucleation mechanisms. Soot formation was found to be most sensitive to phenylacetylene addition and nucleation through physical dimerization appears to be unlikely. Next, the effects of ammonia addition, a possible future fuel, on soot formation in laminar nonpremixed ethylene counterflow flames was performed. A reduction in soot volume fraction was observed and attributed to chemical effects of ammonia addition.
Second, the investigation and development of several types of diagnostics was performed. Soot is typically reported to scale with pressure as Pn where P is pressure and n is a scaling factor. A wide range of scaling factors for ethylene coflow flames have been reported using different types of diagnostics. In this work, a comparison between a light extinction technique and PLII was performed and differences between reported values was explored. Next, the time resolved laser induced incandescence (TiRe-LII) diagnostic was advanced by exploring the effects of SVF on local gas heating. Errors introduced into this model by neglecting local gas heating are explored. Finally, a new diagnostic was developed for 3 dimensional measurements of SVF and velocity in turbulent flames using a technique known as diffuse-backlight illumination extinction imaging.
Third, the application of gated 2D TiRe-LII was assessed in pressurized environments on laminar coflow flames. Comparisons between TiRe-LII and thermophoretically captured soot imaged by transmission electron microscopy (TEM) was performed. TiRe-LII was found to have reasonable agreement with TEM measurements if the SNR was high, but due to the large disparity in primary particle size in pressurized environments errors in 2D TiRe-LII can be significant.
|
Page generated in 0.0727 seconds