No description available.

No description available.

No description available.

The application of glass fiber reinforced composites has grown rapidly due to their high strength-to-weight ratio, low cost, and chemical resistance. However, the increasing demand for fiber reinforced composites results in the generation of more composite wastes. Mechanical recycling is a cost-effective and environmentally-friendly recycling method, but the loss in the quality of recycled glass or carbon fiber composite hinders the wide-spread use of this recycling method. It is important to develop novel composite materials with higher recyclability. Thermotropic liquid crystalline polymers (TLCPs) are high-performance engineering thermoplastics, which have comparable mechanical performance to that of glass fiber. The TLCP reinforced composites, called in situ composites, can form the reinforcing TLCP fibrils during processing avoiding the fiber breakage problem. The first part of this dissertation is to study the influence of mechanical recycling on the properties of injection molded TLCP and glass fiber (GF) reinforced polypropylene (PP). The processing temperature of the injection molding process was optimized using a differential scanning calorimeter (DSC) and a rheometer to minimize the thermal degradation of PP. The TLCP and GF reinforced PP materials were mechanically recycled up to three times by repeated injection molding and grinding. The mechanical recycling had almost no influence on the mechanical, thermal, and thermo-mechanical properties of TLCP/PP because of the regeneration of TLCP fibrils during the mold filling process. On the other hand, glass fiber/PP composites decreased 30% in tensile strength and 5% in tensile modulus after three reprocessing cycles. The micro-mechanical modeling demonstrated the deterioration in mechanical properties of GF/PP was mainly attributed to the fiber breakage that occurred during compounding and grinding. The second part of this dissertation is concerned with the development of recyclable and light weight hybrid composites through the use of TLCP and glass fiber. Rheological tests were used to determine the optimal processing temperature of the injection molding process. At this processing temperature, the thermal degradation of matrix material was mitigated and the processability of the hybrid composite was improved. The best formulation of TLCP and glass fiber in the composite was determined giving rise to the generation of a recyclable hybrid composite with low melt viscosity, low mechanical anisotropy, and improved mechanical properties. Finally, TLCP reinforced polyamide composites were utilized in an additive manufacturing application. The method of selecting the processing temperature to blend TLCP and polyamide in the dual extrusion process was devised using rheological analyses to take advantage of the supercooling behavior of TLCP and minimize the thermal degradation of the matrix polymer. The composite filament prepared by dual extrusion was printed and the printing temperature of the composite filament that led to the highest mechanical properties was determined. Although the tensile strength of the TLCP composite was lower than the glass fiber or carbon fiber composites, the tensile modulus of 3D printed 60 wt% TLCP reinforced polyamide was comparable to traditional glass or carbon fiber reinforced composites in 3D printing. / Doctor of Philosophy / The large demand for high performance and light weight composite materials in various industries (e.g., automotive, aerospace, and construction) has resulted in accumulation of composite wastes in the environment. Reuse and recycling of fiber reinforced composites are beneficial from the environmental and economical point of view. However, mechanical recycling deteriorates the quality of traditional fiber reinforced composite (e.g., glass fiber and carbon fiber). There is a need to develop novel composites with greater recyclability and high-performance. Thermotropic liquid crystalline polymers (TLCP) are attractive high performance materials because of their excellent mechanical properties and light weight. The goal of this work is to generate recyclable thermotropic liquid crystalline polymer (TLCP) reinforced composites for use in injection molding and 3D printing. In the first part of this work, a novel recyclable TLCP reinforced composite was generated using the grinding and injection molding. Recycled TLCP composites were as strong as the virgin TLCP composites, and the mechanical properties of TLCP composites were found to be competitive with the glass fiber reinforced counterparts. In the second part, a hybrid TLCP and glass fiber reinforced composite with great recyclability and excellent processability was developed. The processing conditions of injection molding were optimized by rheological tests to mitigate fiber breakage and improve the processability. Finally, a high performance and light weight TLCP reinforced composite filament was generated using the dual extrusion process which allowed the processing of two polymers with different processing temperatures. This composite filament could be directly 3D printed using a benchtop 3D printer. The mechanical properties of 3D printed TLCP composites could rival 3D printed traditional fiber composites but with the potential to have a wider range of processing shapes.

One of the major limitations in Fused Filament Fabrication (FFF), a form of additive manufacturing, is the lack of composites with superior mechanical properties. Traditionally, carbon and glass fibers are widely used to improve the physical properties of polymeric matrices. However, the blending methods lead to fiber breakage, preventing generation of long fiber reinforced filaments essential for printing load-bearing components. Our approach to improve tensile properties of the printed parts was to use in-situ composites to avoid fiber breakage during filament generation. In the filaments generated, we used thermotropic liquid crystalline polymers (TLCPs) to reinforce acrylonitrile butadiene styrene (ABS) and a high performance thermoplastic, polyphenylene sulfide (PPS). The TLCPs are composed of rod-like monomers which are highly aligned under extensional kinematics imparting excellent one-dimensional tensile properties. The tensile strength and modulus of the 40 wt.% TLCP/ABS filaments was improved by 7 and 20 times, respectively. On the other hand, the 67 wt.% TLCP/PPS filament tensile strength and modulus were improved by 2 and 12 times, respectively. The filaments were generated using dual extrusion technology to produce nearly continuously reinforced filaments and to avoid matrix degradation. Rheological tests were taken advantage of to determine the processing conditions. Dual extrusion technology allowed plasticating the matrix and the reinforcing polymer separately in different extruders. Then continuous streams of TLCP were injected below the TLCP melting temperature into the matrix polymer to avoid matrix degradation. The blend was then passed through a series of static mixers, subdividing the layers into finer streams, eventually leading to nearly continuous fibrils which were an order of magnitude lower in diameter than those of the carbon and glass fibers. The composite filaments were printed below the melting temperature of the TLCPs, and the conditions were determined to avoid the relaxation of the order in the TLCPs. On printing, a matrix-like printing performance was obtained, such that the printer was able to take sharp turns in comparison with the traditionally used fibers. Moreover, the filaments led to a significant improvement in the tensile properties on using in FFF and other conventional technologies such as injection and compression molding. / Doctor of Philosophy / In this work two thermoplastic matrices, acrylonitrile butadiene styrene (ABS) and polyphenylene sulfide (PPS), were reinforced with higher melting thermoplastics of superior properties called thermotropic liquid crystalline polymers (TLCPs). This was done so that the resulting filaments could be 3D-printed without melting the TLCPs. The goal of this work was to generate nearly continuous reinforcement in the filaments and to avoid matrix degradation, and, hence, a technology called dual extrusion technology was used for the filament generation. The temperatures required for filament generation were determined using rheology, which involves the study of flow behavior of complex fluids. Dual extrusion technology allows processing of the constituent polymers separately at different temperatures, followed by a continuous injection of multiple TLCP-streams into the matrix polymers. In addition, the use of static mixers (metallic components kept in the path of flow to striate incoming streams) leads to further divisions of the TLCP-streams which are eventually drawn by pulling to orient the TLCP phase. The resulting filaments exhibited specific properties (normalized tensile properties) higher than aluminum and contained fibers that were nearly continuous, highly oriented, and an order in magnitude lower in diameter than those of carbon and glass fiber, which are commonly used reinforcements. High alignment and lower fiber diameter are essential for printing smoother printed parts. The filaments were intended to be printed without melting the TLCPs. However, previous studies involving the use of TLCP reinforced composites in conventional technologies have reported the occurrence of orientation relaxation on postprocessing, which decreases their tensile v properties. Therefore, temperatures required for 3D printing were determined using compression molding to retain filament properties on printing to the maximum extent. On printing using an unmodified 3D printer, parts were printed by taking 180º turns during material deposition. Contrarily, the use of continuous carbon fibers required a modified 3D printer to allow impregnation during 3D printing. Moreover, the performance comparison showed that the continuous carbon fibers could not be deposited in tighter loops. The properties of the printed parts were higher than those obtained on using short fibers and approaching those of the continuous fiber composites.

The objective of this study is to synthesize nematic-thermotropic liquid crystalline polymers (LCP) and determine their possible application areas. In this context, thirty different LCP&rsquo / s were synthesized and categorized with respect to their fiber formation capacity, melting temperature and mechanical properties. The basic chemical structure of synthesized LCP&rsquo / s were composed of p-acetoxybenzoic acid (p-ABA), m-acetoxybenzoic acid (m-ABA), hydroquinone diacetate (HQDA), terephthalic acid (TPA) and isophthalic acid (IPA) and alkyl-diacids monomers. In addition to mentioned monomers, polymers and oligomers were included in the backbone such as polyethylene terephthalate (PET) and polyethylene naphthalate (PEN) polymers, and polybutylene naphthalate (PBN), polyhexylene naphthalate (PHN) and poly butylene terephthalate (PBT) oligomers that contain different kinds of alkyl-diols. We adjusted the LCP content to have low melting point (180oC-280oC) that is processable with thermoplastics. This was achieved by balancing the amount of linear (para) and angular (meta) groups on the aromatic backbones together with the use of linear hydrocarbon linkages in the random copolymerization (esterification) reaction. LCP species were characterized by the following techniques / Polarized Light Microscopy, Nuclear Magnetic Resonance (NMR), Fourier Transform Infrared Analysis (FTIR), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), X-ray Scattering (WAXS, Fiber diffraction), surface free energy, end group analysis (CEG), intrinsic viscosity (IV) and tensile test. According to these analysis LCPs were classified into five main categories / (I) fully aromatics, (II) aromatics+ PET/PEN, (III) aromatics + oligomers (IV) aromatics + short aliphatic diacids, (V) aromatics + long aliphatic diacids. The foremost results of the analysis can be given as below. DSC analysis shows that some LCPs are materials that have stable LC mesogens under polarized light microscopy. In TGA analysis LCPs that have film formation capacity passed the thermal stability test up to 390oC. NMR results proved that predicted structures of LCPs from feed charged to the reactor are correct. In FTIR due to the inclusion of new moieties, several peaks were labeled in the finger-print range that belongs to reactants. In X-ray analysis, LCP24 (containing PET) was found to be more crystalline than LCP25 (containing PEN) which is due to the symmetrical configuration. Block segments were more pronounced in wholly aromatic LCP2 than LCP24 that has flexible spacers. Another important finding is that, as the amount of the charge to the reactor increases CEG value increases and molecular weight of the product decreases. Selected group V species were employed as reinforcing agent and mixed with the thermoplastics / acrylonitrile butadiene styrene (ABS), nylon6 (PA6), polyethylene terephthalate (PET), polypropylene (PP) and appropriate compatibilizers in micro compounder and twin screw extruder. The blends of them were tested in dog-bone and/or fiber form. In general LCPs do not improve the mechanical properties except in composite application with polypropylene. A significant increase in tensile properties is observed by LCP24 and LCP25 usage. Capillary rheometer studies show that the viscosity of ABS decreases with the inclusion PA6 and LCP2 together. In addition to the composite applications, some LCPs are promising with new usage areas. Such as nano fibers with 200nm diameter were obtained from LCP27 by electrospinning method. The high dielectric constant of LCP29 has shown that it may have application areas in capacitors.

Different monomeric diols, with a central rigid FD unit connected with two aliphatic chains of various length, were prepared to react with aromatic mesogenic triad, TOBC. In this manner, thermotropic polyesters with possible low thermal transition temperatures (including Tmand Ti) and high solubility in organic solvent can be generated in view of the non-linear polymeric chain imposed by the rigid, bent FD moieties. In addition to the effect of the aliphatic chain length, polyesters of different molecular weight will be obtained by different synthesis approach (or fractionation of the resulting polyester product) and therefore, the influence of molecular weight on liquid crystalline properties can be evaluated.

No description available.

Thermoplastic composites that have been reinforced by thermotropic liquid crystalline (TLCP) fibrils in the microscale and by nanoparticles in the nanoscale are defined as multi-scale wholly thermoplastic composites (WTCs). Multi-scale WTCs have been proposed as lightweight replacements with high performance for some traditional glass fiber (GF) and carbon fiber (CF) reinforced composites materials in various applications. TLCPs are known for performing mechanical properties similar to those of the lower end of CF but significantly better than those of GF. To enhance the mechanical properties of TLPC reinforced WTCs, carbon nanotubes (CNTs) are considered being used as a secondary enhancement in WTCs. CNTs have gathered significant interest in the last 30 years because of their high aspect ratio, high mechanical properties, and other high-performance properties. The focus of this work is on investigating the processing conditions of generating in situ injection-molded multi-scale WTCs, then extending the technology to dual-extrusion and fused filament fabrication (FFF) and obtain high-performance multi-scale WTC products. This dissertation initially focused on investigating the processing conditions, in particular mixing histories and processing temperature profiles, of generating in situ injection-molded multi-scale WTCs, which consist of a representative TLCP, scCO2 aided exfoliated CNTs, and the thermoplastic matrix polyamide 6 (PA 6). The supercooling behavior of the TLCP and thermal stability of PA 6 are studied by applying the rheological methods of small amplitude oscillatory shear (SAOS). Multiple mixing histories with CNTs and processing temperature profiles are analyzed based on the criterion of maximizing tensile properties of multi-scale WTCs and minimizing thermal degradation of the matrix. Under the optimum processing conditions, the in situ injection-molded multi-scale WTCs exhibit a 26% and 34% tensile modulus and strength enhancement, compared to the in situ injection-molded WTCs with no CNTs. Scanning electron micrograph (SEM) images were used to understand the enhancement. The second part of this work is to extend the scCO2 aided in situ multi-scale WTCs processing technology to dual-extrusion and FFF. Multi-scale WTC filaments, which consists of TLCP, CNTs, and polyamide copolymer (PAc), are generated by dual-extrusion, and 3D printed into rectangular specimens in FFF. The 1 wt% CNTs reinforced multi-scale WTC filaments generated by the means of dual-extrusion exhibit 225% and 80% improvement in tensile modulus and strength, respectively, compared to the WTC filaments with no CNTs. In FFF, 40 wt% TLCP/1 wt% CNT/PAc 3D printed specimens with filament laid in longitudinal direction exhibited excellent tensile modulus and strength of 38.92 GPa and 127.16 MPa, respectively. The well-dispersed exfoliated CNTs show high alignment with TLCP microfibrils in the multi-scale WTC filaments and their laid-down specimens, which causes the significant tensile modulus enhancement. Bridging elements are discovered between TLCP fibrils and PAc matrix to improve interfacial adhesion, which is attributed to the well-dispersed exfoliated CNTs. Finally, the significant improvements in tensile properties attributed to scCO2 aided exfoliated CNTs in WTCs are verified on the multi-scale WTCs based on polypropylene (PP). Moreover, additional tensile properties improvements for exfoliated CNTs reinforced multi-scale WTCs are obtained with the use of maleic anhydride grafted polypropylene (MAPP). With 1 wt% CNTs and 16 wt% MAPP dual reinforcement, 20 wt% TLCP reinforced WTCs based on polypropylene (PP) exhibit 265%, 274%, and 182% improvement in the tensile modulus of the filaments, laid up specimens in the concentric pattern and laid up specimens in ±45° rectilinear pattern, respectively. The dual reinforcement also improves the tensile strength of 20 wt% TLCP reinforced WTC filaments by up to 73%. The high alignment between TLCP fibrils and CNTs are confirmed in the multi-scale WTCs based on PP. Besides the bridging elements attributed to CNTs found in the second part of this work, SEM images show that CNTs are partially trapped in TLCP fibrils. / Doctor of Philosophy / Considering the need for environmentally friendly materials, novel thermoplastic composites with high mechanical performance, lightweight, and potentially high recyclability properties were generated in this work. Two types of thermoplastic matrices, polyamide (PA or nylon) and polypropylene (PP) were reinforced with carbon nanotubes (CNTs) and rigid chain polymers known as thermotropic liquid crystalline polymers (TLCPs). CNTs are known for their high mechanical properties and high aspect ratio, which are helpful to reinforce thermoplastic composite materials. During injection molding and the dual-extrusion processes, TLCPs deform into almost continuous microfibrils and reinforce the thermoplastic matrices. Instead of using traditional glass fibers or carbon fibers to reinforce thermoplastics, TLCP reinforced thermoplastic composites, which are defined as wholly thermoplastic composites (WTCs), can retain their mechanical properties during the recycling process such as in injection molding and have better performance during the lay-down process in fused filament fabrication. The goal of this work was to generate CNTs reinforced WTCs for use in injection molding and fused filament fabrication with high mechanical performance. In the injection molding process for generating CNTs reinforced WTC end-gated plaques, it was determined that the optimum thermal mixing histories for the CNTs could be identified by the inspections of the tensile property measurements and scanning electron microscopy (SEM). With the obtained optimum thermal mixing histories with CNTs, CNTs reinforced WTC filaments were generated by dual extrusion technology and used in fused filament fabrication. With 1 wt% addition of CNTs, the tensile properties of WTCs were significantly enhanced in both the filament materials and the laid-down parts. Especially, the CNT reinforced WTC filaments based on nylon matrices exhibited competitive tensile moduli to long carbon fiber reinforced nylon composite filaments, which was also competitive to the properties of aluminum alloys. In addition, the laid-down parts of CNTs reinforced WTC based on PP presented further tensile strength improvement due to the improved interfacial adhesion between the laid-down filaments and between layers, which was attributed to the addition of maleic anhydride grafted polypropylene.

This thesis presents results of novel methodologies applied to oriented systems. Both pure liquid crystalline materials as well as molecules oriented in liquid crystalline matrices have been studied. In particular this thesis presents investigations related to various aspects of NMR in liquid crystalline media, such as, assignment of resonances and the study of director dynamics of spinning liquid crystals in different phases and with different symmetry. Simplified methods for structure determination of solutes dissolved in liquid crystal solvents have been proposed. Diffusion ordered spectroscopy has been used to study a mixture of liquid crystals of opposite diamagnetic susceptibility at its coexistent phase. The methods presented represent novel techniques to characterize the liquid crystalline phase. NMR spectroscopy which has become a method of choice for understanding ordering mechanisms of mesogens requires a robust method for obtaining assignments of the NMR spectra of various nuclei that are found in the mesogens [1, 2]. It turns out that the spectra in the isotropic phase and in the nematic phase of a liquid crystal molecule are very different due to the presence of chemical shift anisotropy in the mesophase spectrum. There are a host of methodologies available for assigning spectra in the isotropic phase [3]. These methods however fail, when applied to the spectrum of the molecules in the mesophase due to the dominating role of strong anisotropic interactions, such as homonuclear couplings among protons. Problems arising while assigning spectral lines of liquid crystals in their nematic phase have been dealt with in chapter 2. To circumvent these problems, a property of the liquid crystal molecules under off-magic angle sample spinning can be utilized. It has been shown by Courtieu et al. [4] that the director/symmetry axis of a Δχ + ve liquid crystal aligns along the spinning axis for θ between 0 ° and θm, where θ is the angle between the spinning axis and the magnetic field and θm = 54.7° is the magic angle. It may be noted that the spectrum of θ = 0° spinning angle corresponds to the normal static spectrum, while the spectrum of θ = θm corresponds to the isotropic spectrum. In an earlier study, Teearr et al. [5] had recorded the 13C liquid crystal spectra as a function of very closely spaced θ values from 90° all the way up to 0°. From these plots of chemical shift versus the angle of spinning, it is possible to follow the trajectory of each 13C line from its position from θ = θm to θ = 0° and then match the spectrum in the isotropic phase (equivalently the magic angle sample spinning spectrum of the nematic phase) to the spectrum of the static sample in the nematic phase. However this method requires recording spectra at closely spaced angle intervals, so that one can unambiguously follow the trajectory of each of the lines without missing out any crossover of trajectories. However, this operation is time consuming. In this thesis we propose an alternate method, where we utilize the fact that the above trajectory has a very distinct relationship to the isotropic and anisotropic chemical shift and the problem of assignment does not require a continuous variation of angles, but just a few selected experiments should enable the assignment of the spectrum in the anisotropic phase. Thus the method of assignment has been made simpler and faster. It is shown that in addition to the assigned isotropic spectrum, only one other Off-magic angle spinning spectrum whose spinning angle θ is accurately known is necessary to obtain the complete assignment of the static spectrum. This procedure is non-trivial due to possibilities of errors in assignments arising out of inaccuracies in the knowledge of chemical shifts and the spinning angle. A computational procedure is proposed to take into account deviations arising out of non-ideal experimental conditions. A discussion regarding the details of the procedure and also situations where there can be ambiguities and how they can be resolved has been elaborated. The developed method has been demonstrated on a well known thermotropic liquid crystalline system, N-(4-ethoxybenzylidene)-4-n-butlyaniline [EBBA]. Since assignment of resonances in the nematic phase is a primary requirement for any further analysis regarding the ordering and deeper understanding of the role of various substituents in the mesogens we believe our novel prescription will be of immense use and utility. The third chapter presents the study of director dynamics in a lyotropic liquid crystal composed of Potassium laurate, 1-Decanol and D2O [6] under variable angle sample spinning using 2H NMR spectrum of D2O. A very interesting interplay of the magnetic orienting torque due to interaction of the liquid crystal director with the magnetic field and viscous torque arising from the viscosity of the sample on the director comes to fore. The relative magnitude of these torques has a direct bearing on the spectral pattern and line shapes observed, providing valuable insights into magnetohydrodynamics of the spinning liquid crystals. This study leads to even more interesting behavior for liquid crystals which deviate from uniaxial symmetry. This competition between magnetic and viscous torques has been quantitatively visualized by simulation of the 2H spectrum. It has been possible to visualize the observed spread in the director distribution arising out of viscous torque in terms of the energetics of the system under fast spinning. If the magnetic torque dominates over the viscous torque, then the equilibrium corresponds to the director orientation of δ = 0° where the energy is at its minimum. However the viscous and magnetic torques can become comparable as it may happen if the spinning angle is close to the magic angle or when the Δχ of the system is small. In those circumstances additional energy from the viscous torque causes the distribution of the director orientation to spread further away from δ = 0° for a positive Δχ liquid crystal. The trigonometric factor [P2(cosθ)∗P2(cosδ)] being proportional to the total energy of the system has been plotted against the spinning angle. The spectrum of the biaxial phase [7] as a function of the spinning angle shows more interesting director distribution. Here the patterns of the director distribution are observed on either side of the magic angle due to the presence of more than one director. The patterns observed also have information about the symmetry of the phase. This work provides insights into magnetohydrodynamics of spinning liquid crystals and can also be of relevance to samples of biological interest such as bicelles with protein oriented in them [8]. The fourth chapter deals with a novel characterization method relevant for the biaxial phase [9]. As an off shoot of the previous chapter, it effectively overcomes the disadvantages of the previous experimental methods which require simulation and line shape fitting to extract useful parameters. The chapter also presents the measurement of geometrical parameters of oriented solutes in phases exhibiting biaxial symmetry. The measured parameters show the effect of the onset of biaxiality as significant deviation in the value of the measured parameter. The utility of liquid crystalline media as solvents in high resolution NMR spectroscopy has been very rewarding since the pioneering work of Saupe and Englert [6]. The intramolecular interactions within solutes are only partially averaged. As a result one obtains a liquid like spectrum while at the same time very useful anisotropic interactions such as dipolar couplings, chemical shift anisotropies, quadrupolar couplings and anisotropic part spin-spin J couplings are extracted [10]. NMR spectra of molecules dissolved in thermotropic liquid crystals have long been used to obtain structural and orientational information. As the same time the complexity of the spectrum increases with the increase in the number of spins and the reduction in symmetry of the molecule, which can make the spectral analysis forbidding. Generally proton spectra have been used to obtain the geometry of the proton skeleton of the molecule and the information that includes dilute X nuclei such as 13C and 15N are available only from satellites which are buried in the intense proton spectrum. Different inequivalent dilute spins coupled to protons form different coupled spin systems in their natural abundance and appear as satellites in the proton spectra. Identification of transitions belonging to each of the spin system is essential to determine heteronuclear dipolar couplings, which is a formidable task. The fifth chapter deals with development of the techniques to obtain the complete structure of the dissolved molecules including nuclei other than protons in their natural abundance. The use of inverse experiments has been elaborated to overcome the problems of sensitivity and complexity for solute molecules having larger number of spins. In the present study using HSQC and HMQC experiments, we have selectively detected spectra of each inequivalent rare spin coupled to protons in pyrazine, pyrimidine and pyridazine dissolved in thermotropic Phase 4 and Phase 5 liquid crystal solvents. This way we could obtain enhancement in the intensity of satellites signals without the interference from the signals connected to the major isotopomers. Besides, we could resolve a complex spectrum into its sub-spectra corresponding to individual 13C and 15N isotopomers. This separation of the spectra corresponding to individual sub-spin systems makes analysis easy and helps analyze larger systems with higher number of spins and lower symmetry. Besides 1H-1H dipolar couplings, 13C-1H and 15N-1H dipolar couplings have been determined in natural abundance, thereby giving the complete dipolar coupling network between all the spins in the molecule. In this treatment pyrazine, pyrimidine and pyridazine have been used as examples of methodology developed. It is expected that the method will be of wider use for several other similar systems. Chapter six describes the diffusion ordered spectroscopic investigation [11] of a phase arising out of mixing together two liquid crystals having opposite signs of diamagnetic susceptibility anisotropy [12]. Towards this end we have used CH3CN as a probe molecule. The spectrum of CH3CN has with it the information about the parallel or perpendicular orientation of the phase. Such a mixture of liquid crystals have shown interesting behavior at the critical temperature where the two phases seem to coexist. It has been an interesting question to understand what exactly happens for the molecular orientation when the macroscopic anisotropy Δχ vanishes. Earlier Jokisaari et al. [13] have varied the temperature very finely taking due precautions to maintain homogeneity and stability of temperature to the tune of ±0.05K across the sample volume. Their observation of a powder pattern exactly in the critical temperature was interpreted as arising out of a distribution of directors equally oriented in all directions. In our experiments we have measured the diffusion coefficient of the probe molecule i.e. acetonitrile as we change the temperature of the system through the critical temperature. At the critical temperature we have a situation of being able to measure the parallel and perpendicular orientational diffusion coefficients simultaneously. The measurements show that the parallel component of the diffusion coefficient has reduced and the perpendicular component has increased in comparison to the trend in the immediate neighboring temperatures, thereby indicating that at the exact critical condition the liquid crystal mixture consists of an isotropic distribution of molecules. As a check to rule out any exchange of molecules in different domains of parallel and perpendicular orientations an EXSY experiment was conducted with a mixing time which was same as that of the diffusion delay in the DOSY experiment. The EXSY spectrum showed no exchange cross peaks between the two orientations, this confirms that the anisotropy of the diffusion vanishes at the critical temperature. Nematic liquid crystals exhibit a rich variety of phases and properties. NMR is a very powerful tool to study the various phases at the microscopic and molecular level. It has also turned out that some of these properties can be usefully utilized for investigation of both small and large molecules by NMR. Thus this thesis has attempted to expand several of the techniques already available for various applications and extend the utility of NMR for the study of partially ordered systems.