CAI combustion and the factors affecting it were intensively investigated in a single cylinder, air-assisted gasoline direct injection engine. CAI was achieved by means of residual gas trapping by utilising low-lift short duration camshafts and early closing of the exhaust valves. The effects of EVC (Exhaust Valve Closure) and IVO (Inlet Valve opening) timings, spark timing, single and split injection timings, coolant temperature, compression ratio, cam lift and duration on exhaust emissions and CAI operation were investigated experimentally. Engine speed throughout the course of the experiments, was varied from 1200rpm to 2400rpm and the air/fuel ratio was altered from stoichiometric to the misfire limit. The results show that the EVC timing, compression ratio, cam lift and duration had significant influences on CAI combustion and emissions. Early EVC when combined with higher compression ratio and higher cam lift, enhance CAI combustion operation and stability. IVO timing had minor effect on CAI combustion while spark timing hardly affects CAI operation as soon as fully-developed CAI conditions were established. Coolant temperature was revealed to have substantial impact on CAI combustion when the coolant temperature was below 65C. The results also show the importance of injection timing. Early injection gave faster and more stable combustion, less HC and CO emissions, but more prone to knocking combustion and higher NOx emissions. Furthermore, CAI operation range could considerably be extended with injection during the recompression process. Late injection led to slower and unstable combustion, higher HC and CO emissions but lower combustion noise and NOx emissions. Split injection gave even further extension of CAI range in both stoichiometric and lean mixture operations. All the above clearly suggest, that optimising injection timing and using split injection is an effective way to control and extend CAI operation in a direct injection gasoline engine.

This doctoral thesis is about controlling the combustion timing of the combustion concept Homogeneous Charge Compression Ignition, HCCI, by means of variable valve timings. The HCCI research usually is regarded to have started in Japan during the later part of the 1970´s. The world of HCCI has since grown and HCCI is of today researched worldwide. Of particular interest from a Swedish point of view is that Lund Institute of Technology has emerged as one of the world leading HCCI laboratories. The idea with HCCI is to combine the Otto and Diesel engine. As in an Otto engine the charge is premixed but as in a Diesel engine the operation is unthrottled and the compression heat causes the ignition. The combustion that follows the ignition takes place homogeneously and overall lean. The result is ultra low NOx and particulate emissions combined with high total efficiency. A difficulty with the HCCI-concept is that it only works in a narrow area and that there is no direct way to control the Start Of Combustion, SOC. Out of this follows that timing/phasing of the combustion is one of the main difficulties with HCCI combustion concepts. This is particularly emphasized during transient operation and calls for feedback control of the combustion timing. This work investigates one method, the variable valve timing, to achieve feedback control of the combustion phasing. From the work it can be concluded that the variable valve timing can control the combustion phasing during engine transients. In order to improve the performance a non-linear compensation from ignition delay to valve timings has been suggested, incorporated in a control structure and tested in engine test. The engine test has been performed in a single cylinder engine based on a Scania truck engine. The speed range from 500 to 1750 rpm and the load range 1.26 and 10.5 bar of netIMEP has been covered with fair transient performance. / QC 20100629

Controlled Auto Ignition (CAI) combustion is a new combustion principle in internal combustion engines which has in recent years attracted increased attention. In CAI combustion, which combines features of spark ignition (SI) and compression ignition (CI) principles, air/fuel mixture is premixed, as in SI combustion and auto-ignited by piston compression as in CI combustion. Ignition is provided in multiple points, and thus the charge gives a simultaneous energy release. This results in uniform and simultaneous auto-ignition and chemical reaction throughout the whole charge without flame propagation. CAI combustion is controlled by the chemical kinetics of air/fuel mixture with no influence of turbulence. The CAI engine offers benefits in comparison to spark ignited and compression ignited engines in higher efficiency due to elimination of throttling losses at part and idle loads. There is a possibility to use high compression ratios since it is not knock limited, and in significant lower NOx emission (≈90%) and particle matter emission (≈50%), due to much lower combustion temperature and elimination of fuel rich zones. However, there are several disadvantages of the CAI engine that limits its practical application, such as high level of hydrocarbon and carbon monoxide emissions, high peak pressures, high rates of heat release, reduced power per displacement and difficulties in starting and controlling the engine. Controlling the operation over a wide range of loads and speeds is probably the major difficulty facing CAI engines. Controlling is actually two-components as it consists of auto-ignition phasing and controlling the rates of heat release. As CAI combustion is controlled by chemical kinetics of air/fuel mixture, the auto-ignition timing and heat release rate are determined by the charge properties such as temperature, composition and pressure. Therefore, changes in engine operational parameters or in types of fuel, results in changing of the charge properties. Hence, the auto-ignition timing and the rate of heat release. The Thesis investigates a controlled auto-ignition (CAI) combustion in internal combustion engines suitable for transport applications. The CAI engine environment is simulated by using a single-zone, homogeneous reactor model with a time variable volume according to the slider-crank relationship. The model uses detailed chemical kinetics and distributed heat transfer losses according to Woschini's correlation [1]. The fundamentals of chemical kinetics, and their relationship with combustion related problems are presented. The phenomenology and principles of auto-ignition process itself and its characteristics in CAI combustion are explained. The simulation model for representing CAI engine environment is established and calibrated with respect to the experimental data. The influences of fuel composition on the auto-ignition timing and the rate of heat release in a CAI engine are investigated. The effects of engine parameters on CAI combustion in different engine concepts fuelled with various fuels are analysed. The effects of internal gas recirculation (IEGR) in controlling the auto-ignition timing and the heat release rate in a CAI engine fuelled with different fuels are investigated. The effects of variable valve timings strategy on gas exchange process in CAI engine fuelled with commercial gasoline (95RON) are analysed.