Correcting wind tunnel data for wall interference is a critical part of relating the acquired data to a free-air condition. Accurately determining and correcting for the interference caused by the presence of boundaries in wind tunnels can be difficult especially for facilities employing ventilated boundaries. In this work, three varying levels of ventilation at the National Transonic Facility (NTF) were modeled and calibrated with a general slotted wall (GSW) linear boundary condition to validate the computational model used to determine wall interference corrections. Free-air lift, drag, and pitching moment coefficient predictions were compared for a range of lift production and Mach conditions to determine the uncertainty in the corrections process and the expected domain of applicability. Exploiting a previously designed statistical validation method, this effort accomplishes the extension of a calibration and validation for a boundary pressure wall interference corrections method. The foundational calibration and validation work was based on blockage interference only, while this present work extends the assessment of the method to encompass blockage and lift interference production. The validation method involves the establishment of independent cases that are then compared to rigorously determine the degree to which the correction method can converge free-air solutions for differing interference fields. The process involved first establishing an empty-tunnel calibration to gain both a centerline Mach profile of the facility at various ventilation settings, and to gain a baseline wall pressure signature undisturbed by a test article. The wall boundary condition parameters were then calibrated with a blockage and lift interference producing test article, and final corrected performance coefficients were compared for varying test section ventilated configurations to validate the corrections process and assess its domain of applicability. During the validation process discrimination between homogeneous and discrete implementations of the boundary condition was accomplished and final results indicated comparative strength in the discrete implementation's ability to capture experimental flow physics. Final results indicate that a discrete implementation of the General Slotted Wall boundary condition is effective in significantly reducing variations caused by differing interference fields. Corrections performed with the discrete implementation of the boundary condition collapse differing measurements of lift coefficient to within 0.0027, drag coefficient to within 0.0002, and pitching moment coefficient to within 0.0020. / Doctor of Philosophy / The purpose of conducting experimental tests in wind tunnels is often to acquire a quantitative measure of test article aerodynamic characteristics in such a way that those specific characteristics can be accurately translated into performance characteristics of the real vehicle that the test article intends to simulate. The difficulty in accurately simulating the real flow problem may not be readily apparent, but scientists and engineers have been working to improve this desired equivalence for the better part of the last half-century. The primary aspects of experimental aerodynamics simulation that present difficulty in attaining equivalence are: geometric fidelity, accurate scaling, and accounting for the presence of walls. The problem of scaling has been largely addressed by adequately matching conditions of similarity like compressibility (Mach number), and viscous effects (Reynolds number). However, accounting for the presence of walls in the experimental setup has presented ongoing challenges for ventilated boundaries; these challenges include difficulties in the correction process, but also extend into the determination of correction uncertainties. Exploiting a previously designed statistical validation method, this effort accomplishes the extension of a calibration and validation effort for a boundary pressure wall interference corrections method. The foundational calibration and validation work was based on blockage interference only, while this present work extends the assessment of the method to encompass blockage and lift interference production. The validation method involves the establishment of independent cases that are then compared to rigorously determine the degree to with the correction method can converge free-air solutions for differing interference scenarios. The process involved first establishing an empty-tunnel calibration to gain both a centerline Mach profile of the facility at various ventilation settings, and to gain a baseline wall pressure signature undisturbed by a test article. The wall boundary condition parameters were then calibrated with a blockage and lift interference producing test article, and final corrected performance coefficients were compared for varying test section ventilated configurations to validate the corrections process and assess its domain of applicability. During the validation process discrimination between homogeneous and discrete implementations of the boundary condition was accomplished and final results indicated comparative strength in the discrete implementation's ability to capture experimental flow physics. Final results indicate that a discrete implementation of the General Slotted Wall boundary condition is effective in significantly reducing variations caused by differing interference fields. Corrections performed with the discrete implementation of the boundary condition collapse differing measurements of lift coefficient to within 0.0027, drag coefficient to within 0.0002, and pitching moment coefficient to within 0.0020.

No description available.