The aim of diploma thesis is design and lay-out of high pressure pumping station with plunger pumps for splash of scales from slabs of hot-rolled. Theoretic (introduction) part of this thesis contain description of formation of scales and description of ways how it is possible remove these scales. And this part contains also explication of effect of water jet on solid material. The practical part of diploma thesis is focused on design of pumping station including of dimensioning of machinery. Part of this work is also technical documentation for proposed pumping station and specification of main machines and devices.

Tato diplomová práce je zaměřena na porovnání různých turbulentních a chemických modelů na příkladu volné metanové trysky ústící do vzduchu. Nejprve je uveden teoretický úvod k modelům, následován CFD (Ansys Fluent) simulacemi plamene pomocí vybraných modelů. Jako součást práce je provedeno a vyhodnoceno experimentální měření. V závěru jsou experimentální výsledky porovnány s nasimulovanými daty.

This master’s thesis deals with measurement of spray characteristics of Effervescent atomizers intended for burning waste and heavy fuels. Atomizers were tested on cold test bench by means of Phase Doppler Anemometry. Spray characteristics were evaluated for many different regimes of pressure, temperature and Gas to liquid ratio. The aim of this measurement is to compare flow regimes and their influence on the quality of spray characteristics. The theoretical part describes basic fundamental principles of liquid atomization, effervescent atomization and principles of laser diagnostic methods. The practical part is engaged with improvements in test bench and setting up and optimization of the laser measuring system. Results contain visualization of spray, velocity profiles and drop size distribution in various operating flow regimes of the jet.

Diplomová práce se zabývá experimentální studií vlastností spreje z několika malých tlakových vířivých trysek používaných ve spalovacích komorách proudových motorů. Po desetiletí byla snaha zlepšit jejich rozprašovací charakteristiky a stále jsou možnosti, které nebyly téměř prozkoumány. Výzkum byl proveden za použití různých geometrií jednotlivých dílů trysky za účelem zjištění jejich vlivu na sprej. Byl použit různý počet vstupních portů (2, 3 a 4), různé vířivé komůrky (kulová, kuželová, konvexní, nízká kuželová) a rozdílné návrhy obtokového otvoru (osové, mimosové). Důraz byl kladen na posouzení stability spreje, kde pulzující sprej negativně ovlivňuje provozní charakteristiky spalovací komory. Vlastnosti spreje byly proměřeny fázovým dopplerovským analyzátorem, cirkulární homogenita byla hodnocena mechanickým paternátorem a rozpad kapaliny byl vizualizován pomocí jednoduchého laserového stínografu.

The doctoral thesis deals with an experimental study of several diagnostic techniques intended for plasma diagnostics and diagnostics of thin films during reactive sputter deposition. A relatively novel probe diagnostic technique called Floating harmonic probe for measurement of the ion density and electron tem- perature in technological low-temperature plasma is studied. A Langmuir probe is commonly used, however, its application in conditions where non-conducting films are being deposited can be problematic or unreliable. The floating harmonic probe measurement technique deals with this inherent problem of the Langmuir probe. The Floating harmonic probe results are compared to those obtained by a classical Langmuir probe in non-reactive DC continuously driven discharge, and its applicability in reactive regime during deposition of iron oxide thin films is proved. The work deals also with a modification of the Floating harmonic probe called Phase Delay Harmonic Analysis Method which is intended for diagnostics of pulsed driven discharges. The second part of the thesis is devoted to a new proposed method for in-situ diagnostics of thin films. This method monitors the capacitance and resistance of a thin film during deposition up to the frequencies in the kHz range. This new method could be used for...

This diploma thesis was focused on the possibility of using a plasma nozzle to accelerate the wound healing process. The benefits of using low-temperature plasma in medicine or biomedical applications are known from many studies, and low-temperature plasma is already used to sterilize medical devices, materials or surgical instruments. Some studies also report a high potential of usinh plasma nozzle in the treatment of skin wounds. In the experimental part of this work, an in vitro wound healing test was performed using two different low-temperature plasma sources. Source No. 1 was a surface wave microwave discharge and source No. 2 was a torch microwave discharge. An in vitro scratch healing test was performed on a monolayer of HaCaT keratinocytes and testing was performed using various parameters. The influence of the plasma treatment time was monitored, as well as the influence of the plasma discharge power and also the influence of the argon working gas flow. Especially when using a torch microwave discharge, faster wound healing was recorded at most of the parameters used compared to the control. Thus, it can be said that this source appears to be potentially suitable for faster wound healing. Furthermore, in the work using the MTT cytotoxicity test, the viability of skin cells after their plasmination was also monitored using the same conditions as in the in vitro wound healing test. When performed in the standard MTT assay, none of the settings or sources used showed any cytotoxic effects on keratinocytes. LDH cytotoxicity tests were also performed concurrently to verify the accuracy of the MTT assays. The results of both tests agreed and the use of low-temperature plasma in skin treatment can be considered as safe. Overall, the results show that the plasma nozzle can find use in medicine in the healing of skin wounds and chronic defects as a potentially fast, inexpensive and effective method.

Master´s thesis Hydrodynamic mixing of water-ash mixture in vessel is interested in describing fluid and solid particles flow in a vessel. The mixing was conducted in cylindrical vessel by a radial nozzle. The goal of the thesis is to describe flow field and places where the most of the particles are descending according to position, depth, flow rate and nozzle orientation in the vessel. An experiment was conducted in order to investigate and document 8 different positions and orientation of the nozzle. Significant changes in flow fields and mixing time were observed. A mathematical model of the vessel with the nozzle was created in Fluent program. Places with the lowest velocities according to the model were in good agreement with places where the most of the solid particles were descending.

Diplomová práce se zabývá měřením charakteristik sprejů dvou tlakových vířivých trysek pro spalovací komoru malého turbínového motoru na zkušebním stavu za studena pomocí metod Particle Image Velocimetry (PIV) a fázové Dopplerovské anemometrie (PDA). Cílem měření bylo stanovit a porovnat charakteristiky sprejů obou trysek. Výsledky měření mají objasnit rozdílnost chování trysek za provozu a možný dopad na proces spalování. Úvodní teoretická část pojednává o základních fyzikálních principech atomizace kapalin, konstrukci a oblasti uplatnění tlakových vířivých trysek a o principech laserových diagnostických metod použitých při experimentálním měření. Nasledující část popisuje návrh a montáž zkušební trati a dalších zařízení navržených pro experimentální měření v této práci. Experimentální část se zabývá nastavením parametrů měřícího systému a zpracováním dat. Výsledky měření zahrnují vektorová rychlostní pole, axiální rychlostní profily a distribuce velikosti kapek pro různé provozní podmínky obou trysek.

Master thesis deals with design of combusting chamber for gaseous fuels with predicted thermal output less than 30 kilowatts. Designed equipment will be used as a generator of flue gases with required parameters further used for experimental catalytic unit. Due to the need of draft creation inside the combustion chamber and exhaust pipe is master thesis also deals with design of ejector nozzle, which will be used for this purpose. Opening chapters of this work, considering a theoretical part, are focused on basic classification of combustion chambers and industrial burners. Next and main chapter is dedicated to main goal of this work, which is combustion chamber design, containing necessary calculations divided into balance calculation and construction design. Final chapters deals with above mentioned calculation of ejector nozzle ensuring sufficient draft and also sufficient cooling of flue gases incoming from catalytic unit.

The diploma thesis describes design of bladeless machine known as a Tesla turbine. The work is divided into theoretical part, practical part involving the design and experimental measurements of made bladeless turbine and a final assessment of thesis. The theoretical part deals with the basic design features of bladeless machines and their design modifications and flow in the nozzles. Furthermore there is a dedicated part of the dynamics of working fluid in the rotor of bladeless turbine represented by CFD modeling. The practical part includes the design and construction of parts of the turbine on a preliminary calculation using an analytical model of the flow in the turbine. The designed turbine components were checked for operational safety with structural calculations of shaft and disk impeller. The thesis was also performed experimental measuring of parameters of designed bladeless turbine. Measured values were compared with the analytical model which predicted turbine efficiency. In conclusion, besides to assessment, thesis also outlines possible proposals for further improvements of constructed bladeless turbine.