Neste trabalho, propõe-se um modelo numérico-computacional representativo dos processos de tratamento térmico, que seja uma ferramenta eficiente e forneça meios para um entendimento efetivo do mecanismo de geração de tensões residuais durante a têmpera de aços. Foram investigados os fenômenos térmicos, mecânicos e de transformação de fase observados na têmpera, bem como o acoplamento entre esses três fenômenos. O modelo utiliza o Método dos Elementos Finitos (MEF) e o programa ABAQUS®, além de rotinas numéricas em FORTRAN responsáveis pela resolução do problema termo-mecânico-microestrutural acoplado. A utilização de sub-rotinas, que implementam uma alteração na formulação (matemática e numérica) do programa de Elementos Finitos, permite incluir no modelo as informações presentes em uma curva CRC (curva de resfriamento contínuo) do aço SAE 4140, implementando o cálculo de deformações da peça simulada de modo incremental e cumulativo. Os resultados mostram que a utilização das sub-rotinas desenvolvidas neste trabalho permitiu implementar, conjuntamente com o programa ABAQUS®, o cálculo das frações volumétricas, durezas, distorções e tensões que surgem em um tratamento térmico de têmpera, simulando as transformações martensítica, perlítica, bainítica e ferrítica. Os resultados dos modelos foram equivalentes aos relatados pela literatura, principalmente no que se refere às durezas e tensões associadas a cada transformação de fase. Em particular, os resultados indicam que a transformação martensítica está sempre associada à formação de tensões compressivas. Ensaios experimentais foram realizados a fim de validar os modelos computacionais propostos, utilizando-se um teste Jominy adaptado e instrumentado, de modo a permitir a amostragem da variação de temperaturas no material. Ensaios metalográficos permitiram correlacionar as frações volumétricas transformadas durante a têmpera do corpo de prova Jominy aos valores calculados pelo modelo numérico acoplado. / The objective of this work is to analyze residual strains and stresses and volumetric expansion due to phase transformations that occur during quenching of a steel body, as well as to predict these phase transformations. The coupled thermo-mechanical-phase transformation problem was analyzed, specifically in terms of the quenching process. Different computational models were presented, based on the finite element software ABAQUS® and on the use of FORTRAN subroutines. The continuous-cooling-transformation (CCT) diagrams of SAE 4140 steel are represented differently in each model, depending on the transformed phases and correspondent volumetric expansion. These subroutines include information from the CCT diagrams of SAE 4140 into a FORTRAN code. The subroutine calculates all the microstructures resulting from quenching (ferrite, pearlite, bainite, and martensite), depending on cooling rate. The numerical analysis conducted in this work provided results in terms of the temperature and stresses developed during quenching. The properties determined in this work are hardness, yield strength, volumetric fraction and distortion. Hardness has been predicted by the use of analytical equations. The finite element analyses were able to explain and reproduce phenomena observed during quenching of a steel cylinder. In particular, numerical results indicated that martensite formation is always related to a compressive stress field. The results of the models are in qualitative agreement with data provided by literature, particularly, in relation to the stresses originated by each different phase transformation during quenching process. Experimental testing was conducted, based on the analysis of the quenching of a Jominy probe, in order to validate the computational model developed in this work.

This research focused on a comprehensive microstructural and mechanical property characterisation study of the Ni-Fe-Cr alloys 718 and 945X. The aim of the project was to better understand the relationship between performance and microstructure of existing (Alloy 718) and newly developed (Alloy 945X) high strength nickel alloys focusing on downhole applications. The main difference between the two alloys is that alloy 945X has lower Nb content than alloy 718, which may minimise the tendency to form delta when combined with correct processing. Previous studies have related the hydrogen embrittlement in alloy 718 with the collection of hydrogen by delta phase. Microstructural characterisation of the new alloy 945X after long term isothermal exposure up to 120 hours in the temperature range 650◦C to 900◦C was conducted with scanning electron microscopy (SEM), to generate a time-temperature-transformation (TTT) diagram. The TTT diagram was used as a road map for designing two isothermal heat treatments of alloy 945X on tensile specimens. Then, the effect of hydrogen charging on the tensile properties and microstructure of the 'as-received' and these two variant heat treatments was investigated. Fractographic analysis showed that, in the presence of hydrogen, intergranular fracture occurred for all the heat treatments, regardless the presence of delta phase at grain boundaries. There was no simple correlation between the volume fraction of delta-phase and susceptibility to hydrogen assisted embrittlement. Rather, it was demonstrated that the morphology and distribution of delta-phase along grain boundaries plays a key role and the other precipitate phases also have an influence through their effect on the ease of strain localisation. This study also examined the hydrogen embrittlement sensitivity of nickel alloy 718 given four different heat treatments to obtain various microstructural states. Each heat treatment leads to differences in the precipitate morphologies of γ', γ'' and delta phases. Material characterisation and fractography of the examined heat treatments were performed using a high resolution FEG-SEM. Three specimens of each condition were pre- charged with hydrogen and tensile properties were compared with those of non-charged specimens. It was observed that hydrogen embrittlement was associated with intergranular and transgranular microcrack formation, leading to an intergranular brittle fracture. delta phase may assist the intergranular crack propagation, and this was shown to be particularly true when this phase is coarse enough to produce crack initia- tion, but this is not the only factor determining embrittlement. Other microstructural features play a role, as does the strength of the material. Finally, the evolution of delta-(Ni3Nb) phase in alloy 718 from the early stages of precipitation, with a particular focus on identifying the grain boundary characteristics that favour precipitation of grain boundary delta phase was investigated. Results showed that delta phase was firstly formed on Σ3 boundaries after 5 hours at the examined temperature (800◦C). Increasing ageing time at 800◦C was observed to lead to an increase in size and precipitation of phases γ'-γ''-delta, an increase in fraction of the special CSL boundaries and an evolution in the morphology of twins and the growth of grains.

High performance multifunctional epoxy resin systems are becoming increasingly important as matrix materials for the advanced composites used in aerospace, electronics, automotive and other industries. In a composite based on epoxy resin systems, a three-dimensional network of the matrix is formed around the reinforcing fibre as a result of the chemical reaction between the resin and the curing agent. This chemical process, known as curing, is an important event to he considered in the production of composite components made up of these resin systems. Two process parameters namely viscosity and chemical conversion are of paramount significance in the production of composite materials Curing studies of the resin systems based on these two parameters, would therefore assume great importance in deciding the performance reliability of the end product. The objectives of the present investigation are 1. to study the cure kinetics of three thermoset resin systems, viz., i) epoxy novolac (EPIT)/ diamino diphenyl methane{DDM), ii) trigylcidyl para- ammo phenol (TGPAP)/toluene diamine (TDA) and iii) tetraglycidyl diamino diphenyl methane (TGDDM)/pyridine diamine(PDA) using the cure kinetic models based on chemical conversion (α), Theological conversion (β) and viscosity. 2.to develop a correlation between a and viscosity (η) and modify an existing autocatalytic model based on α, to the viscosity domain and 3.to investigate the cure behaviour of these systems in terms of the TTT cure diagram and its associated models. EPN/DDM, TGPAP/PDA and TGDDM/PDA resin systems were chosen for the studies to represent a range of functionalities, The cure was monitored using differential scanning calorimetry (DSC), fourier transform infrared (FTIR) and dynamic mechanical analysis (DMA) techniques by following the changes in enthalpy, functional groups and rheology, respectively. The kinetic parameters namely, order of reaction and activation energy were estimated from dynamic DSC data using the methods of Freeman-Carroll and Ellerstein using nth rate expression. Barton, Kissinger and Osawa methods were employed to find out the activation energy from the peak/equal conversion at different heating rates. Isothermal DSC data were also analyzed using nth order model and it was observed that the data could be fitted satisfactorily only for higher temperatures The results obtained from the analysis of both dynamic and isothermal DSC data using nth order model clearly indicate that this model is inadequate for describing the cure behavior. The isothermal DSC data was analyzed by the autocatalytic models of Hone and Kamal Good correlation was observed with Hum and Kamal models up to 60-70%, 25% and 45% conversions for EPN/DDM, TGPAP/TDA and TCDDM/PDA systems respectively. However, the parameters m and n in Kamal model were found to be temperature dependent for EPN/DDM and TCPAP/TDA systems. The limited applicability of the autocatalytic models IK attributed to the counter-effect offered by the intra-molecular bonding taking place. The primary amine and epoxy groups conversions obtained from FTIR were analyzed using autocatalytic model and the kinetic parameters were calculated. The reactivity ratio of the primary amine and the secondary amine with epoxy was found to be dependent on temperature in agreement with the recent findings reported m the literature. The existing models that relate the cure kinetics and the rheological changes, are dual Arrhenius nth order model and autocatalytic model The nth order kinetic model was used to evaluate the kinetic parameters using the viscosity data at different cure temperatures under isothermal conditions As the storage modulus, G' is proportional to the chemical cross links and becomes significant only after the g<4 point, it was used to follow the changes in conversion known as rheoconversion after the gel point The rheoconversion was found by normalizing the G' data with G1^, the storage modulus of the fully cured resin It was used to study the cuie kinetics using an autocatalytic model The kinetic parameters such as rate constant, acceptation and retardation parameters were evaluated and that temperature dependence was established. While the existing models relate viscosity and conversion only up to gel point the new proposed model, termed VISCON model takes into account the changes up to vitrification. The relation so developed is used to modify the autocatalytic cure model based on chemical conversion. The parameters appearing in this model were evaluated using Levenberg-Marquardt error minimization algorithm. The kinetic parameters obtained are comparable with the values estimated using the DSC data. All the models cited above represent the microkinetic aspects. The models based on the information of TTT cure diagrams, however, represent the macrokinetic aspects of the cure, as they are based on the cure stages such as gelation and vitrification TTT diagram relates the cure characteristics like cure temperature, cure time, Ta and, indirectly, chemical conversion Hence the ultimate properties of the composite could he predicted and established with the help of the models based on TTT cure diagrams The changes in the storage modulus, G1 and loss modulus, G", were followed to identify the gel and vitrification points of the resin systems at different cure temperatures Gel point and vitrification point were used to generate gelation and vitrification hues in the construction of TTT cure diagrams for EPN/DDM, TGPAP/TDA and TGDDM/PDA resin systems Theoretical TTT diagrams were generated and IBO-T, contours were established using the TTT diagram-based models The cure schedule for the resin systems investigated could be determined from the TTT diagram and the respective rheological data.

Neste trabalho, propõe-se um modelo numérico-computacional representativo dos processos de tratamento térmico, que seja uma ferramenta eficiente e forneça meios para um entendimento efetivo do mecanismo de geração de tensões residuais durante a têmpera de aços. Foram investigados os fenômenos térmicos, mecânicos e de transformação de fase observados na têmpera, bem como o acoplamento entre esses três fenômenos. O modelo utiliza o Método dos Elementos Finitos (MEF) e o programa ABAQUS®, além de rotinas numéricas em FORTRAN responsáveis pela resolução do problema termo-mecânico-microestrutural acoplado. A utilização de sub-rotinas, que implementam uma alteração na formulação (matemática e numérica) do programa de Elementos Finitos, permite incluir no modelo as informações presentes em uma curva CRC (curva de resfriamento contínuo) do aço SAE 4140, implementando o cálculo de deformações da peça simulada de modo incremental e cumulativo. Os resultados mostram que a utilização das sub-rotinas desenvolvidas neste trabalho permitiu implementar, conjuntamente com o programa ABAQUS®, o cálculo das frações volumétricas, durezas, distorções e tensões que surgem em um tratamento térmico de têmpera, simulando as transformações martensítica, perlítica, bainítica e ferrítica. Os resultados dos modelos foram equivalentes aos relatados pela literatura, principalmente no que se refere às durezas e tensões associadas a cada transformação de fase. Em particular, os resultados indicam que a transformação martensítica está sempre associada à formação de tensões compressivas. Ensaios experimentais foram realizados a fim de validar os modelos computacionais propostos, utilizando-se um teste Jominy adaptado e instrumentado, de modo a permitir a amostragem da variação de temperaturas no material. Ensaios metalográficos permitiram correlacionar as frações volumétricas transformadas durante a têmpera do corpo de prova Jominy aos valores calculados pelo modelo numérico acoplado. / The objective of this work is to analyze residual strains and stresses and volumetric expansion due to phase transformations that occur during quenching of a steel body, as well as to predict these phase transformations. The coupled thermo-mechanical-phase transformation problem was analyzed, specifically in terms of the quenching process. Different computational models were presented, based on the finite element software ABAQUS® and on the use of FORTRAN subroutines. The continuous-cooling-transformation (CCT) diagrams of SAE 4140 steel are represented differently in each model, depending on the transformed phases and correspondent volumetric expansion. These subroutines include information from the CCT diagrams of SAE 4140 into a FORTRAN code. The subroutine calculates all the microstructures resulting from quenching (ferrite, pearlite, bainite, and martensite), depending on cooling rate. The numerical analysis conducted in this work provided results in terms of the temperature and stresses developed during quenching. The properties determined in this work are hardness, yield strength, volumetric fraction and distortion. Hardness has been predicted by the use of analytical equations. The finite element analyses were able to explain and reproduce phenomena observed during quenching of a steel cylinder. In particular, numerical results indicated that martensite formation is always related to a compressive stress field. The results of the models are in qualitative agreement with data provided by literature, particularly, in relation to the stresses originated by each different phase transformation during quenching process. Experimental testing was conducted, based on the analysis of the quenching of a Jominy probe, in order to validate the computational model developed in this work.

This thesis describes the role of cost effective maintenance in achieving competitive advantages. It explores by means of a survey which maintenance practices are used, and how maintenance policies are selected in Swedish industries. Also, it suggests a model for selecting the most cost effective maintenance policy, and how to improve the effectiveness of condition based maintenance decision-making. Finally it discusses how to assess the impact of maintenance practices on business strategic objectives. The main results achieved in the thesis are 1) A better understanding of maintenance organisation, management, systems and maintenance status in Swedish industry. For example, it was found that about 70% of Swedish companies still consider maintenance as a cost centre. Preventive and predictive maintenance approaches are also emphasised. 2) Most Swedish firms, i.e. about 81%, use the accumulated knowledge and experience within the company as a method for maintenance selection. Besides, about 31% use a method based on modelling the time to failure and optimisation. About 10% use failure mode effect and criticality analysis (FMECA) and decision trees and only 2% use multiple criterion decision-making (MCDM). However, the most used maintenance selection method is not the one most satisfactory to its users. Furthermore, about 30% use a combination of at least two methods. 3) A practical model for selecting and improving the most cost effective maintenance policy was developed. It is characterised by incorporating all the strengths of the four methods used in industry. 4) A mechanistic model for predicting the value of vibration level was verified both at the lab and in a case study. 5) A model for identifying, assessing, monitoring and improving the economic impact of maintenance was developed and tested in a case study. Thus it was proved that maintenance is no longer a cost centre, but could be a profit-generating function. To achieve competitive advantages, companies should do the right thing, e.g. use the most cost effective maintenance policy, and they should do it right, e.g. ensure that they have the right competence. Furthermore, they should apply the never-ending improvement cycle, i.e. Plan-Do-Check-Act, which requires identifying problem areas by assessing the savings and profits generated by maintenance and monitoring the economic impact of the applied maintenance policy. Thus, they would know where investments should be allocated to eliminate the basic reasons for losses and increase savings. The major conclusion is that proper maintenance would improve the quality, efficiency and effectiveness of production systems, and hence enhances company competitiveness, i.e. productivity and value advantages, and long-term profitability.

In the modern practice, a sustainable development strategy in a domain of wasteutilization is shifting its focus from a general completeness of recycling to a morespecific attention to efficiently utilize elements in the wastes. This is well-illustrated bythe steelmaking slag industries. The major waste product from the steelmaking practiceis slag and its main constituents are: CaO, SiO2, Al2O3, MnO, FeO and so on. The mainfield of application for the steelmaking slags is civil engineering, especially for road andwaterway construction. However, a significant amount of the slag remains in the dumps,damaging the environment as well as requiring a land for secure storage. Efficientrecycling of these materials is of increasing interest worldwide as a result of increasingsustainability in processes with respect to increasing raw material costs and wastereduction.In order to find a practical solution, joint efforts are currently made at the RoyalInstitute of Technology, Sweden and National Metallurgical Academy of Ukraine. Theconcept is based on transformation of non-magnetic wüstite (FeO) to magneticmagnetite (Fe3O4) using an oxidizing atmosphere was proposed.In order to verify the feasibility of the proposed way of slag utilization, experiments onthe ternary CaO-FeO-SiO2 and quaternary CaO-FeO-SiO2-MnO slags systems,accompanied by thermodynamic and kinetic modelling, were performed. The crystalprecipitation during synthetic slag oxidation was observed by Confocal Scanning LaserMicroscopy (CSLM). Precipitated phases were found to be magnetite and manganeseferrite in the spinel form.Obtained magnetite and manganese ferrite can be separated from the slag by magneticseparation.The formation of nanosize manganese ferrite from the CaO-FeO-SiO2-MnO slag systemduring oxidation was investigated. Experiments were conducted in a horizontalresistance furnace in an oxidizing atmosphere (air). The final product was analysed by Xraydiffraction (XRD). The particles size of the manganese ferrite was estimated by theScherrer formula and was found to be of the order of 23-25 nm. In order to get anunderstanding of the magnetic properties of the manganese ferrite recovered from slagtreatment, it was necessary to synthesize a reference compound from pure precursors.The MnFe2O4 nanopowder was synthesized by the oxalate route. The size effects on themagnetic properties of manganese ferrite particles were investigated.IIThe potential way of the magnetite particles separation from liquid slags was investigatedby cold model studies. The experimental technique of mobilising non-conducting,nonmagnetic particles in conducting liquid in crossed electric and magnetic fields wasinvestigated in order to find the way of the particle separation from the liquidsteelmaking slags. The effects of the current density, magnetic field, size and shape ofthe particle on the particle velocity under action of the electromagnetic buoyancy force(EBF) in the electrolyte were analyzed. / QC 20100916