The aim of this study is to advance the present capability for modelling soot production and thermal radiation from turbulent jet diffusion flames. Turbulent methane / air jet diffusion flames at atmospheric and elevated pressure are studied experimentally to provide data for subsequent model development and validation. Methane is only lightly sooting at atmospheric pressure whereas at elevated pressure the soot yield increases greatly. This allows the creation of an optically thick, highly radiating flame within a laboratory scale rig. Essential flame properties needed for model validation are measured at 1 and 3 atm. These are mean mixture fraction, mean temperature, mean soot volume fraction, and mean and instantaneous spectrally resolved radiation intensity. These two flames are modelled using the parabolic CFD code GENMIX. The combustion/turbulence interaction is modelled using the conserved scalar/laminar flamelet approach. The chemistry of methane combustion is modelled using a detailed chemistry laminar flame code. The combustion model accommodates the non-adiabatic nature of the flames through the use of multiple flamelets for each scalar. The flamelets are differentiated by the amount of radiative heat loss that is included. Flamelet selection is carried out through the solution of a balance equation for enthalpy, which includes a source term for the radiative heat loss. A new soot model has been developed and calibrated by application to a laminar flame calculation. Within the turbulent flame calculations the soot production is fully coupled to the radiative loss. This is achieved through the use of multiple flamelets for the soot source terms and the inclusion of the radiative loss from the soot (as well as the gases) in the enthalpy source. Spectral radiative emission from the flames has been modelled using the RADCAL code. Mean flame properties from the GENMIX calculations are used as an input to RADCAL.

No description available.

This thesis reports the results of a detailed programme of research on airblast atomization carried out using a specially designed atomizer in which the liquid is first spread into a thin sheet and then exposed on both sides to high velocity air. The primary aim of the investigation was to examine the influence of air and liquid properties on atomization quality. The work was divided into four main phases:- (1) The first phase was confined to the effects of liquid properties, namely viscosity, surface tension and density on mean drop size. Special liquids were produced to study the separate effect of each property on atomization quality. They presented a range of values of viscosity from 1.0 to 124 centipoise, while surface tension and density were varied between 26 and 73.5 dynes/cm and 0.8 and 1.8 gm/cm3 respectively. Atomizing air velocities covered the range of practical interest to the designers of continuous combustion systems and varied between 60 and 125 m/sec.(2) To obtain experimental data on the influence of air properties, notably air density, on mean drop size, the air temperature was varied between 23 and 151°C at atmospheric pressure in one series of experiments, while a separate study on the effect of air pressure on atomization quality was undertaken, where tests were conducted at constant levels of air velocity and temperature, using a range of liquid flows from 5 to 30 gm/sec, at various levels of air pressure between 1 and 8.5 atm. (3) In order to provide a comprehensive picture of airb1ast atomizer performance over a wide range of conditions the separate effects of varying air velocity, liquid flow rate, and hence atomizing air/liquid mass ratio on SMD were examined. This study enabled a better understanding of the effects of changes in operation on the atomizer's performance. (4) In all three phases above, velotities of both inner and outer atomizing air streams were kept equal. This last phase was aimed at studying the effect of varying the velocity between the inner and outer air streams. Best atomization quality was achieved when 65% of the total atomizing air was flowing through the outer stream. A detailed description of the light-scattering technique for drop size measurement is included. A discussion on the importance of the results obtained and their direct relevance to the design of airblast atomizers is given. A dimensional analysis and inspection of all the data obtained on the effects of air and liquid properties on atomization quality showed that over the following range of conditions: Liquid viscosity 1.0 to 44 centipoise Liquid surface tension 26 to 73.5 dynes/cm Liquid density 0.78 to 1.5 gm/cm³ Air velocity 70 to 125 m/sec Air temperature 20 to 151 °c Air pressure 1.0 to 8.5 kgf/cm².

No description available.

No description available.

No description available.

No description available.

No description available.

No description available.

A combined cycle is one of the thermal cycles used in thermal power plants. It consists of a combination of a gas and a steam turbine, where the waste heat from the gas turbine is used for steam generation in the heat recovery steam generator. The aim of the diploma thesis was the conceptual design of a combined cycle electricity source and the balance calculation of the cycle. The calculation is based on the thermodynamic properties of the substances and the basic knowledge of the Brayton and Rankin-Clausius cycle. The result is the amount and parameters of air, flue gases, and steam/water in individual places and the technological scheme of the source, in which these parameters are listed.