A low-speed, axisymmetric turbulent boundary layer under a strong adverse pressure gradient is experimentally studied for its relevance to marine applications, urban air-transportation and turbulence ingestion noise. The combined effect of lateral curvature and streamwise pressure gradient are examined on the mean flow, turbulence structure, velocity correlations and wall pressure fluctuations. Additionally, the upstream influence of a rotor operating in this flow is examined to improve the understanding of the turbulence necessary to develop advanced noise prediction tools. Measurements were made in Virginia Tech Stability tunnel documenting the flow over a 0.432-m diameter body-of-revolution comprised of a forward nose-cone, a constant diameter mid-body and a 20 degree tail-cone, at a length based Reynolds number of 1.2 million. The principal finding of this work is the resemblance of the boundary layer to a free-shear layer where the turbulence far from the wall plays a dominant role, unlike in the canonical case of the flat-plate boundary layer. The mean flow along the tail developed inflection points in the outer regions and the associated velocity and turbulence stress profiles were self-similar with a recently proposed embedded shear layer scaling. As the mean flow decelerates downstream, the large-scale motions energize and grow along with the boundary layer thickness; However, the structure is roughly self-similar with the shear-layer scaling, emphasizing the role of the shear-layer in the large-scale structure. Additionally, the correlation structure is discussed to provide information towards the development of turbulence models and aeroacoustic predictions. The associated wall pressure fluctuations, measured with a longitudinal array of microphones, evolved significantly downstream with the dimensional wall pressure spectra weakening by over 20-dB per Hz. However, the spectra collapsed to within 2-dB with the wall-wake scaling, where the pressure-scale is the wall shear stress, and the time-scale is derived from the boundary layer thickness and edge velocity. The success of this scaling, even in the viscous roll-off regions, suggests the increasing importance of the outer region on the near-wall turbulence and wall-pressure. Investigation of the space-time structure revealed the presence of a quasi-periodic feature with the conditional signature of a roller-eddy. The structure appeared to scale with the wall-wake scaling, and was found to convect downstream at speeds matching those at the inflection points (and outer turbulence peak). It is hypothesized that the outer region turbulence in strong adverse pressure gradient flow strongly drive the near-wall turbulence and therefore both the wall pressure and shear stress. Subsequent measurements made with the rotor operating at the tail, using high-speed particle image velocimetry, provided the space-time structure of the inflow turbulence as a function of the rotor thrust. The impact of the rotor on the mean flow, turbulence and correlation structure in the vicinity of the rotor is discussed to supply information towards validating numerical simulations and developing turbulence models that account for the distortion due to the rotor. This work was sponsored by the Office of Naval Research, in particular Drs. Ki-Han Kim and John Muench under grants N00014-17-1-2698 and N00014-20-1-2650. / Doctor of Philosophy / Understanding turbulent flows adjacent to surfaces placed in fluid flows is necessary to develop efficient technologies to mitigate undesirable drag, vibrations and noise. Particularly, this is of an increased interest with the imminent abundance of urban short-haul air transportation. While several fundamental aspects of these flows have been clarified, certain specific areas still remain to be addressed, including the impact of curved surfaces, like those of submarine hulls and aircraft fuselage, and the impact of mean pressure gradients. This study seeks to fill some of these gaps by studying the flow over a body-of-revolution through wind tunnel experiments. The nature of the velocity and wall-pressure fluctuations are examined in detail. It was found that the boundary layer was significantly different from the canonical case of a flat-plate flow, with the mean velocity and turbulence structure developing the characteristics of a free-shear layer (flows unbounded by surfaces). Specifically, the velocity and turbulence intensity appeared self-similar with a recently proposed embedded shear layer scaling, which is based on the parameters at the inflection point in the mean velocity profile. The large-scale motions in the outer regions, despite energizing and growing as the flow decelerated downstream, appeared self-similar with the shear layer parameters, emphasizing the role of shear layer motions within in the boundary layer. This is important since the turbulence relatively further from the wall are now the important sources of pressure fluctuations and therefore drag, vibrations and noise. The associated wall-pressure fluctuation were studied with a focus on the wall-pressure spectrum and the space-time structure. A quasi-periodic feature was detected in the instantaneous fluctuations, which had a conditional structure reminiscent of a conditional roller, and appeared to convect downstream at speeds matching those at the inflection points in the velocity profile. Therefore it is hypothesized that the large-scale motions in the embedded shear layer play a dominant role on the near-wall turbulence and therefore on the wall pressure and shear-stress. This is different from the behavior of the wall-studied flow past a flat-plate. It is therefore important to factor this into technologies aiming to increase the efficiency and quieten the vehicles

A rotor immersed in a thick turbulent boundary layer produces unsteady loading on the blades which generates unwanted noise and vibration. Two point velocity fluctuations were measured in detail to determine the full four-dimensional correlation function of a boundary layer generated over a smooth wall in the Virginia Tech Stability Wind Tunnel. The correlation function reveals anisotropy in the flow dominated by a large scale correlation structure elongated in the streamwise direction and inclined relative to the wall. This correlation function was then evaluated in the blade frame of reference of an idealized 10 bladed rotor partially immersed in the flow. Blade to blade upwash coherence shows significant asymmetry which is a direct result of the anisotropy of the flow. Using a newly developed theory, the correlation function was used to predict the far-field radiated noise from the rotor at various operating and flow conditions. Predictions show the sound field is dominated by the effects of "haystacking" which is further increased with the inclusion of the presence of the wall. Directivity predictions suggest the far-field sound field acts like a monopole/dipole combination. / Master of Science

Two rotor configurations with different non-uniform inflows were studied: a rotor ingesting the wake of an upstream cylinder and a rotor ingesting a thick axially symmetric boundary layer from an upstream centerbody. In both cases, the undisturbed inflow was measured without the rotor present in order to characterize the inflow, in particular to calculate the unsteady upwash velocity distribution at the location of the rotor. In addition, detailed acoustic measurements were completed using a 251-channel large-area microphone array. In all, over 400 conditions covering different advance ratios, angles of yaw, and inflow conditions were measured. Measurements of the sound show that the source has a complex directivity, different from that of a streamwise aligned dipole, due to the inhomogeneous unsteady upwash distribution. In addition, observers at different far field locations will perceive sources from different locations on the rotor disk. The directivity is a function of both the rotor geometry and turbulent inflow. A simplified model of the sound source was developed using these inputs and accurately predicts trends observed in the far field noise. For the cylinder wake ingestion case, on-blade measurements of the flow field show that the wake is drawn to the center of the rotor disk with increasing thrust. This is particularly noticeable if the wake does not strike the center of the rotor disk. The effects of this flow distortion on the far field directivity are well predicted by the model. The effects of yaw to rotate the produced sound field can be inferred from this model as well. A novel beamforming procedure was used to isolate sources across the face of the rotor for the cylinder wake ingestion case for an upstream observer position. This method may be used to isolate different sound sources on a rotor if multiple sources are present or if different regions of the rotor disk need to be isolated. The directivity of a rotor ingesting an axially symmetric boundary layer is far less complex than the ingestion of a two-dimensional cylinder wake, but measurements still show the perceived source location shift with observer location. Overall, the proposed noise modeling technique is an efficient method to predict the directivity of turbulence ingestion noise for inhomogeneous inflows. This can enable quick absolute noise predictions at all far field locations using only a single point measurement or far field noise prediction to establish absolute levels. / Doctor of Philosophy / In many engineering applications, rotors interact with turbulence. Aircraft and ships with rear mounted propellers can have upstream appendages or discontinuities that generate turbulence that travels downstream and is drawn into the propeller. Wind turbines interact with turbulence in the atmosphere and with turbulent wakes from other turbines. Interaction of a rotor with turbulence results in unsteady loading on the rotor blades that can radiate as sound, causing unwanted community noise or vehicle detection. As such, prediction and reduction of noise due to turbulence ingestion is highly desirable and remains an active area of research. Turbulence ingestion noise is well understood from first principles and can be successfully predicted provided an accurate description of the turbulent inflow and unsteady aerodynamic response of the rotor blades. Much work has focused on homogenous, isotropic turbulence ingestion noise, however, in practical applications, the rotor inflow is often non-uniform, anisotropic, and can change dramatically with the thrusting condition of the rotor. Research efforts to develop noise predictions considering these more complex, but practical inflows have focused on the inflow modeling and measurement and have relied on a small subset of sound measurements for validation. The present study seeks to provide new physical insight into inhomogeneous, anisotropic turbulence ingestion noise through wind tunnel experiments. In particular, two rotor configurations with different practical non-uniform inflows are studied: a rotor ingesting the wake of an upstream cylinder and a rotor ingesting a thick axially symmetric boundary layer from an upstream center body. In both cases, the undisturbed inflow was measured without the rotor present in order to characterize the inflow, and detailed acoustic measurements were completed using a 251-channel large-area microphone array. In all, over 400 rotor operating conditions were measured. The acoustic directivity in each case is examined in detail as a function of rotor operating condition. A simplified directivity model is developed and validated with measurements. Ultimately, the directivity model can provide a good engineering approximation of the full directivity with reduced computational time or can be used to extrapolate measured results to positions in the far field where placement of sensors is not possible. The results can also be used to guide the analysis and interpretation of single point or microphone array measurements in the acoustic far field of a rotor.

The effect of flow anisotropy and three dimensional separation on the turbulent structure and radiated turbulence ingestion noise of a rotor in two experimental configurations is studied. The first consists of a non-axisymmetric boundary layer wake ingested by a rotor mounted at the aft of a body of revolution inclined at 5 degree angle of attack. In the second configuration a transient disturbance is generated by an upstream wing body junction pitching from zero to 20 degree angle of attack . This disturbance is convected downstream and ingested into a rotor immersed in a wall boundary layer. In both cases flow velocimetry at the rotor inflow is done and the far field sound is measured. The flow velocimetry in the wake of the inclined body of revolution shows evidence of three dimensional separation and vortex rollup between the lee and body sides. A boundary layer embedded shear layer develops as the turbulent kinetic energy is pulled off the wall by the flow separation and is visible in the port side velocimetry. The turbulent structure of this shear layer and the boundary layer on the lee of the body is visualized using compact eddy structure representation and the modes on the port side are shown to be stretched versions of similar modes seen in an equilibrium, zero pressure gradient boundary layer. The effect these structures had on the radiated sound served to both increase blade to blade correlation and the overall broadband levels of the sound. Measurements of the sound using an acoustic array showed directivity effects that resulted from the location of the embedded shear layer and rollup vortices. Although the vortices likely have some effect on the spectra, most of the noise is dominated by the turbulence ingestion of the embedded shear layer. For the second experimental configuration the transient motion was documented through repeated measurements of the flow field and sound, and an ensemble average of the measurements taken. Overall the flow was unsteady, particularly in the outer region of the boundary layer. The sound radiated was shown to be tonal during the first half of the interaction, where the flow is dominated by a deterministic mean flow change, and attributed to a form of periodic unsteady loading. During the latter half of the disturbance the broadband and overall sound levels increased significantly and are associated with the interaction of the rotor with flow separation over the wing body junction when it reached a critical, 16 degree angle of attack. / Doctor of Philosophy / The interaction of rotors and propellers with turbulence is commonly encountered when vehicles transit fluid mediums. In vehicles with aft mounted propellers, such as pusher type aircraft or underwater vehicles, turbulent boundary layers developed over the vehicle surface are ingested by the propeller. The size or scale of the average turbulent eddy greatly affects the type of sound generated by the interaction. For eddies that are small enough to only interact with one blade, the blade angle of attack varies randomly as it rotates through the turbulence and this radiates broadband sound. However, if the blade encounters eddies that are large or long enough to interact with multiple blades then the angle of attack, and thus the fluctuating lift force, begins to be correlated for each passage of the blade. This is known as blade to blade correlation and produces energy and sound concentration around the frequencies that correspond to the blade passage. This phenomenon is fairly well understood and many attempts have been made to model and predict the sound spectra from a rotor encountering turbulence in this manner. However these models often assume isotropic and homogenous turbulence when making predictions. This assumption works well in many applications, however, often the turbulence the rotor encounters is anisotropic with significant flow inhomogeneities. Thus, experimental investigations into the mechanisms and sources of sound in inhomogenous and anisotropic flows is necessary in an attempt to inform further flow and acoustic models. In this dissertation the inflow and acoustic response of a rotor ingesting significantly complex and anisotropic flows is characterized. It focuses on two commonly encountered flow arrangements; a rotor mounted at the stern of a body of revolution at an angle of attack, and a rotor ingesting a turbulent wall boundary layer with transient disturbances introduced by an upstream wing body junction. In both cases the flow is three dimensional and the rotor encounters significant circumferential turbulence variation during its rotation through the resultant turbulent flow field. For the flow about the body of revolution the flow and noise appear to be driven by the rotor interaction with an embedded shear layer that results from three dimensional separation between the lee and windward sides of the body. For the transient disturbance interaction the rotor noise response shows two separate noise sources. During the first half of the disturbance the blade response is tonal and associated with a deterministic blade angle of attack change as the rotor interacts with the transient. In the latter half of the disturbance the rotor broadband noise is significantly increased due to flow separation over the wing body junction.

Acoustic and aerodynamic measurements have been carried out on a rotor operating in a planar turbulent boundary layer near a wall for a variety of thrust conditions and yaw angles with respect to the inflow. At the highest thrust condition a strong flow reversal in the wall-rotor tip gap was observed. Average velocity fields filtered by the angular position of the rotor show that the flow reversal is fed by jets of fluid that tend to form below the blade as it passes by the wall. Instantaneous velocity measurements show the presence of strong vortices in the tip gap. These vortices were characterized and found to be both stronger and more numerous on the downstroke side of the tip gap. Additionally, vortices with the same handedness as the bound circulation in the blade were more numerous and only located on the downstroke side of the tip gap. Those with the opposite handedness were found to be only located on the upstroke side. Unexpectedly strong far-field acoustic response at the blade passage frequency at this highest thrust condition and is believed to be due to an interaction of the blade tip with these vortices. At moderate thrust, when the rotor was yawed toward the downstroke side the far field acoustic response at the blade passage frequency was found to increase. The opposite was true as it was yawed toward the upstroke side. At the highest thrust, however the unyawed rotor had the strongest blade passage frequency response which is believed to be due to stronger vortex-tip interaction in this case. / Master of Science