• Refine Query
  • Source
  • Publication year
  • to
  • Language
  • No language data
  • Tagged with
  • 2
  • 2
  • 2
  • 2
  • 2
  • 2
  • 1
  • 1
  • 1
  • About
  • The Global ETD Search service is a free service for researchers to find electronic theses and dissertations. This service is provided by the Networked Digital Library of Theses and Dissertations.
    Our metadata is collected from universities around the world. If you manage a university/consortium/country archive and want to be added, details can be found on the NDLTD website.
1

Endwall Heat Transfer and Shear Stress for a Nozzle Guide Vane with Fillets and a Leakage Interface

Lynch, Stephen P. 08 May 2007 (has links)
Increasing the combustion temperatures in a gas turbine engine to achieve higher efficiency and power output also results in high heat loads to turbine components downstream of the combustor. The challenge of adequately cooling the nozzle guide vane directly downstream of the combustor is compounded by a complex vortical secondary flow at the junction of the endwall and the airfoil. This flow tends to increase local heat transfer rates and sweep coolant away from component surfaces, as well as decrease the turbine aerodynamic efficiency. Past research has shown that a large fillet at the endwall-airfoil junction can reduce or eliminate the secondary flow. Also, leakage flow from the interface gap between the combustor and the turbine can provide some cooling to the endwall. This study examines the individual and combined effects of a large fillet and realistic combustor-turbine interface gap leakage flow for a nozzle guide vane. The first study focuses on the effect of leakage flow from the interface gap on the endwall upstream of the vane. The second study addresses the influence of large fillets at the endwall-airfoil junction, with and without upstream leakage flow. Both studies were performed in a large low-speed wind tunnel with the same vane geometry. Endwall shear stress measurements were obtained for various endwall-airfoil junction geometries without upstream leakage flow. Endwall heat transfer and cooling effectiveness were measured for various leakage flow rates and leakage gap widths, with a variety of endwall-airfoil junction geometries. Results from these studies indicate that the secondary flow has a large influence on the coverage area of the leakage coolant. Increased leakage flow rates resulted in better cooling effectiveness and coverage, but also higher heat transfer rates. The two fillet geometries tested affected coolant coverage by displacing coolant around the base of the fillet, which could result in undesirably high gradients in endwall temperature. The addition of a large fillet to the endwall-airfoil junction, however, reduced heat transfer, even when upstream leakage flow was present. / Master of Science
2

Effects of Realistic First-Stage Turbine Endwall Features

Cardwell, Nicholas Don 03 January 2006 (has links)
The modern gas turbine engine requires innovative cooling techniques to protect its internal components from the harsh operating environment typically seen downstream of the combustor. Much research has been performed on the design of these cooling techniques thus allowing for combustion temperatures higher than the melting point of the parts within the turbine. As turbine inlet temperatures and efficiencies continue to increase, it becomes vitally important to correctly and realistically model all of the turbine's external cooling features so as to provide the most accurate representation of the associated heat transfer to the metal surfaces. This study examines the effect of several realistic endwall features for a turbine vane endwall. The first study addresses the effects of a mid-passage gap, endwall misalignment, and roughness on endwall film-cooling. The second study focuses on the effect of varying the combustor-to-turbine gap width. Both studies were performed in a large-scale low speed wind tunnel with the same vane geometry. Geometric and flow parameters were varied and the variation in endwall cooling effectiveness was evaluated. Results from these studies show that realistic features, such as surface roughness, can reduce the effectiveness of endwall cooling designs while other realistic features, such as varying the combustor-to-turbine gap width, can significantly improve endwall cooling effectiveness. It was found that, for a given coolant mass flowrate, a narrow combustor-turbine gap width greatly increased the coverage area of the leaked coolant, even increasing adiabatic effectiveness upstream of the vane stagnation point. The turbine designer can also more efficiently utilize leaked coolant from the combustor-to-turbine gap by controlling endwall misalignment, thereby reducing the overall amount of film-cooling needed for the first stage. / Master of Science

Page generated in 0.0728 seconds