Spelling suggestions: "subject:"viva "" "subject:"väva ""
1 |
Fully variable, simple and efficient - electrohydraulic - valve train for reciprocating enginesSchneider, Wolfgang 26 June 2020 (has links)
A new camless electrohydraulic valve train concept for combustion engines was developed at Empa (Swiss Federal Laboratories for Materials Science and Technology, Dübendorf, Switzerland) and tested on a spark ignition passenger car engine. Besides full flexibility with regard to lift and timing of the engine gas exchange valves it features robustness, simplicity and in particular a low own drive power need due to a maximum of hydraulic energy recuperation. The engine test results confirm substantial
efficiency gains in classical as well as in hybrid power trains while also maintaining additional advantages. The system also has the potential to become a key element for load control of piston based compressors and expanders, reciprocating Joule Cycle engines and derivable future electricity storage systems.
|
2 |
Advancing Diesel Engines via Cylinder DeactivationCody M Allen (6594053) 10 June 2019 (has links)
The transportation sector continues to be a primary source of greenhouse gas (GHG) emissions, contributing more than any other sector in the United States in 2017. Medium-duty and heavy-duty trucks trail only passenger cars as the largest GHG contributor in this sector [1]. The intense operating requirements of these vehicles create a reliance on the diesel engine that is projected to last for many decades. Therefore, it is vital that the efficiency and environmental sustainability of diesel engines continue to be advanced.<br><br>Cylinder deactivation (CDA) is a promising technology to improve diesel engine fuel efficiency and aftertreatment thermal management for emissions reduction. This work presents original experimental results demonstrating fuel efficiency improvements of CDA implemented on a modern engine at idle operating conditions through testing of various CDA configurations. Idle calibration optimizations result in up to 28% fuel consumption reduction at steady-state unloaded idle operation and 0.7% fuel consumption reduction over HD-FTP drive cycles at equivalent emissions levels. The low-load thermal management performance of CDA is also investigated through creep and extended idle transient cycles, during which CDA is shown to reduce fuel consumption by up to 40% with similar thermal management performance and reduced NOx and soot emissions. <br><br>Variants of CDA implementation are explored through an experimental comparison of deactivation strategies. The effort described here compares charge trapping strategies through examination of in-cylinder pressures following deactivation because: (1) choice of trapping strategy dictates the in-cylinder pressure characteristics of the deactivated cylinders, and (2) deactivated cylinders can affect torque, oil consumption, and emissions upon reactivation. Results discussed here suggest no significant differences between the strategies. As an example, the in-cylinder pressures of both trapping strategies are shown to converge as quickly as 0.8 seconds after deactivation.<br><br>Finally, the NVH effects of CDA are characterized through studies of torsional vibration, linear vibration, and acoustics. CDA causes frequency content at reduced frequencies compared to conventional operation, which has effects on all aspects of NVH. This creates possible constraints on achievable fuel efficiency and thermal management performance by restricting CDA usage. An alternate form of CDA, dynamic cylinder activation (DCA), is explored as a possible option of avoiding undesirable frequency output while maintaining the desired engine performance. <br>
|
3 |
Fractional Oxidation State Control of Three-Way Catalyst with Stoichiometric Spark-Ignition Natural Gas Engines incorporating Cylinder DeactivationYunpeng Xu (14266550) 15 December 2022 (has links)
<p>A novel two-loop estimation and control strategy is proposed to reduce the natural gas (NG) spark-ignition (SI) engine tail pipe emissions, with focus on the outer loop development. In the outer loop, an fractional oxidation state (FOS) estimator consisting of a three-way catalyst (TWC) model and an extended Kalman-filter is used to estimate the real-time TWC's FOS, and a robust controller is used to control the first-half TWC's FOS by manipulating the desired engine lambda (i.e., air–fuel equivalence ratio; lambda=1 at stoichiometry). The outer loop estimator and controller are combined with an industry-production baseline inner loop controller, which controls the engine $\lambda$ based on the desired lambda value. This novel two-loop control strategy reduces more CH4 and NOx emissions over no-outer-loop control strategy and the conventional two-loop control strategies through simulation. </p>
<p><br></p>
<p>Engine with and without fuel cut-off are both investigated. Although fuel cut-off brings better fuel economy, it also over-oxidizes the TWC during fuel cut events, which makes the FOS-based controller's competence in NOx reduction over non-FOS-based controllers less significant. By comparing simulation results with and without fuel cut-off, it shows huge potential for much better emission result if fuel cut-off's side effect can be alleviated. Considering that fuel cut-off generally being cutting engine fueling during zero load periods and introducing unreacted oxygen into the after-treatment system, the best way of dealing with the issue is to cut off or reduce the oxygen input to the TWC during those events. Several advanced engine technologies such as cylinder deactivation and exhaust gas re-circulation are good candidates to approach this issue. </p>
<p><br></p>
<p>An industry-production Cummins B6.7N natural gas SI engine was installed in the Ray W. Herrick Laboratories for study of variable valve actuation (VVA) technology, for the purpose of evaluating/improving SI engine's fuel efficiency, emission reduction, and engine knock resistance. A one-dimensional, physics-based natural gas SI engine model was investigated and calibrated in GT-Power software. To calculate the burn rates in the cylinder, three different pressure analysis methods were investigated and implemented. It is observed that all six cylinders' pressure curves are different, which in turn render different burn rates cylinder-to-cylinder. Cylinder with a higher peak cylinder pressure has a faster burn rate. Each operating condition has its unique pressure curve, and their burn rates are different under different operating conditions. Considering that the burn rate profile can vary cylinder-to-cylinder and operation-to-operation, to make the GT combustion model work for a larger range of loads, a fixed burn rate model may help in the preliminary research phase, but a predictive combustion model is more preferable.</p>
<p><br></p>
<p>The GT-Power model's VVA capability is investigated, where intake valve closure (IVC) modulation and cylinder de-activation (CDA) are built and analyzed. To mitigate TWC's over-oxidation issue during engine's fuel cut-off events, the CDA is implemented and simulated to demonstrate its benefit on further emission and fuel consumption reductions.</p>
|
4 |
Paläoökologie eines Küstenmoores aus dem Eozän Mitteleuropas am Beispiel der Wulfersorder Flöze und deren Begleitschichten / (Hemstedter Oberflözgruppe, Tagebau Helmstedt)Lenz, Olaf Klaus 26 January 2000 (has links)
No description available.
|
5 |
Geochemie Porifera-reicher Mud Mounds und Mikrobialithe des Mittel- und Oberdevons (Westaustralien, Nordfrankreich) / Geochemistry of Porifera-rich mud mounds and microbialites of the Middle and Upper Devonian (Western Australia, Northern France)Hühne, Cathrin 07 November 2005 (has links)
No description available.
|
Page generated in 0.0214 seconds