Thin walled beams warp under torsional and longitudinal loads. Warping restraint produces high longitudinal stresses. This is an analysis of the stress distribution in the side members of commercial vehicle chassis frames under the effects of the previously little studied longitudinal loads which may act on a truck chassis through spring hanger brackets. The structure analysed is a model chassis frame consisting of channel section side members and four cross members with different joint connections. The developed theories are incorporated into a special purpose finite element program which may be used in the preliminary stages of chassis frame design. Although the program is only used for the longitudinal load case in this thesis, it is generally applicable for other chassis load cases, including torsion, bending, etc. and combination of these. The theoretical results obtained from the program and the finite element analysis on complete chassis frame models are validated against experiments performed on a strain-gauged chassis frame model constructed with the same dimensions and constructional details as the finite element models with the appropriate loading and boundary conditions. Suggestions for the optimum design and attachment positions for components such as spring hanger bracket which may apply longitudinal loads to the side members of the chassis frame are discussed from the point of view of longitudinal loadings.

This thesis presents the results of a comprehensive research study of the bearing behaviour of single or multiple bolted plates in bolt shear at ambient and elevated temperatures. A total of 18 tests were carried out to provide detailed experimental information on bearing behaviour of plates with single bolt. A series of parametric studies using the commercial finite element package ABAQUS were conducted to investigate the effects of different design parameters on the connected plate bearing behaviour, including initial stiffness, ultimate resistance and deformation at the ultimate resistance. The finite element models were verified by comparing the simulated results against the author’s tests conducted as part of this research and other researchers’ test results. Based on the parametric study results, an analytical model was proposed to predict the bearing load-deformation relationship of bolted plate in bolt shear. It was found that the stiffness and ultimate resistance could be predicted accurately by using existing methods. The main contribution of the analytical study was the development of a simple method to calculate the maximum plate deformation (bolt-hole elongation) at the ultimate resistance, based on proposed strain distributions according to different failure modes. This method has been verified against the parametric study results and has been found to be suitable for ambient and elevated temperature applications.

No description available.

No description available.

This thesis presents a theoretical study into the behaviour of thin-walled metal tubes that are filled with elastic material. The study has considered the behaviour and design of concrete-filled steel columns by analysing the effect of the combined actions of axial compression and bending on closed stainless steel cross-sections with a concrete infill as well as the elastic buckling of square, circular and elliptical thin-walled steel tubes, when filled with elastic material. The elastic local buckling of a rectangular plate having four edges clamped and subjected to in-plane linearly varying uniaxial loading with and without juxtaposition with a rigid infill has also been studied. Concrete-filled composite columns find widespread use globally in engineering structures because of their optimal strength and ease of construction. Enhancing the strength of filled columns by utilising newer materials such as stainless steel or shape memory alloys for the skin of the cross-section of the column will increase the construction cost of the column. In order to circumvent this increased construction cost, or to minimise it, the metal skin should be as thin as possible. Members with thin-walled cross-section are prone to lateral torsional buckling, and in particular they are prone to local buckling, with the latter buckling mode playing an important role in the strength of a composite column with a concrete infill. The local buckling coefficient is enhanced by the provision of a rigid concrete infill, and efficient design must make use of this fact to minimise the cost of the skin. The initial portions of this thesis demonstrate the beneficial effects that the rigid concrete core has on the overall strength, and also on the local buckling behaviour of thin-walled metal tubes. The local buckling of the metal skin has been modelled in this thesis by using a Ritz-based energy method. In bi-lateral and uni-lateral buckling studies of rectangular plates, a more general trigonometric function has been selected by application of boundary conditions to the chosen shape function, with these boundary conditions being implemented to make the chosen shape function satisfy the edge conditions for the problem under consideration. The restraining medium is modelled as a tensionless foundation and this restraint condition is introduced through a penalty method formulation. Extensive comparative, convergence, and parametric studies have been carried out by considering a wide range of uni-laterally constrained plates. Following a concise review of the available literature, techniques for analysing the elastic local buckling of thin-walled square tubes, fully filled with elastic materials and subjected to concentric uni-axial compression, are formulated by means of a simple stiffness approach and a proper Ritz-based technique. This method is then extended to account for the local buckling of thin-walled circular and elliptical cylinders with elastic infill. By representation of a proper trigonometric displacement function in the formulation which is capable of incorporating the effects of the penetration zone in a harmonic form, in addition to satisfying all the necessary boundary conditions, it is shown that the buckling solution reduces to a dimensionless representation for which the relevant geometrical and material properties that govern the local buckling coefficient can be identified. It was found that the provision of lightweight and low density infill is functional and attractive with respect to an increase in the efficacy of the restraint. A comparison was made, and good agreement was found to exist, between the results obtained from this study and results that are available in the literature. Finally, a strength to weight index is introduced that quantifies the enhancement in the local buckling coefficient for a number of materials with a wide range of stiffness and density. This index has potential applications for optimal design in aerospace and other specialized engineering applications.

The high speed machining is now recognized as one of the key manufacturing technologies. It possesses several better characteristics than those of a conventional machining way. For example, low chip load, and low cutting-heat generation can be obtained. It also contributes to high productivity and throughput. In this thesis, the technique about the high speed machining for cutting the aluminum thin-walled components will be discussed. An audio signal measuring system will be established to measure sound pressure for avoiding chatter. Meanwhile, the tool path will also be revealed in this thesis.

published_or_final_version / Civil and Structural Engineering / Master / Master of Philosophy

The current interest in collapse characteristics brought about by crashworthiness requirements ýas shown the need for a better understanding and predictive capability for the thin walled open section structures. In general three possible modes exist in which a loaded thin walled open section column can buckle: 1) they can bend in the plane of one of the principal axes; 2) they can twist about the shear. centre; 3) or they can bend and twist simultaneously. The following study was undertaken to investigate the general failure of thin walled open section structures. A literature survey was conducted and it prevailed that a basic fundamental theoretical study was vital in describing the behaviour of thin walled structural members. The following stages of theoretical study have been completed: 1) Formulation of the stiffness matrix to predict the generalised force-displacement relationships assuming the small displacement theory in the linear elastic range. 2) Formulation of the geometric stiffness matrix to predict the buckling criteria under generalised loading and end constraints in the linear elastic range. 3) Formulation of the compound coordinate transformation matrix to relate local and global displacements or forces. 4) Preparation of the associated finite element computer program to solve general thin walled open sections structural problems.

This thesis presents a theoretical study into the behaviour of thin-walled metal tubes that are filled with elastic material. The study has considered the behaviour and design of concrete-filled steel columns by analysing the effect of the combined actions of axial compression and bending on closed stainless steel cross-sections with a concrete infill as well as the elastic buckling of square, circular and elliptical thin-walled steel tubes, when filled with elastic material. The elastic local buckling of a rectangular plate having four edges clamped and subjected to in-plane linearly varying uniaxial loading with and without juxtaposition with a rigid infill has also been studied. Concrete-filled composite columns find widespread use globally in engineering structures because of their optimal strength and ease of construction. Enhancing the strength of filled columns by utilising newer materials such as stainless steel or shape memory alloys for the skin of the cross-section of the column will increase the construction cost of the column. In order to circumvent this increased construction cost, or to minimise it, the metal skin should be as thin as possible. Members with thin-walled cross-section are prone to lateral torsional buckling, and in particular they are prone to local buckling, with the latter buckling mode playing an important role in the strength of a composite column with a concrete infill. The local buckling coefficient is enhanced by the provision of a rigid concrete infill, and efficient design must make use of this fact to minimise the cost of the skin. The initial portions of this thesis demonstrate the beneficial effects that the rigid concrete core has on the overall strength, and also on the local buckling behaviour of thin-walled metal tubes. The local buckling of the metal skin has been modelled in this thesis by using a Ritz-based energy method. In bi-lateral and uni-lateral buckling studies of rectangular plates, a more general trigonometric function has been selected by application of boundary conditions to the chosen shape function, with these boundary conditions being implemented to make the chosen shape function satisfy the edge conditions for the problem under consideration. The restraining medium is modelled as a tensionless foundation and this restraint condition is introduced through a penalty method formulation. Extensive comparative, convergence, and parametric studies have been carried out by considering a wide range of uni-laterally constrained plates. Following a concise review of the available literature, techniques for analysing the elastic local buckling of thin-walled square tubes, fully filled with elastic materials and subjected to concentric uni-axial compression, are formulated by means of a simple stiffness approach and a proper Ritz-based technique. This method is then extended to account for the local buckling of thin-walled circular and elliptical cylinders with elastic infill. By representation of a proper trigonometric displacement function in the formulation which is capable of incorporating the effects of the penetration zone in a harmonic form, in addition to satisfying all the necessary boundary conditions, it is shown that the buckling solution reduces to a dimensionless representation for which the relevant geometrical and material properties that govern the local buckling coefficient can be identified. It was found that the provision of lightweight and low density infill is functional and attractive with respect to an increase in the efficacy of the restraint. A comparison was made, and good agreement was found to exist, between the results obtained from this study and results that are available in the literature. Finally, a strength to weight index is introduced that quantifies the enhancement in the local buckling coefficient for a number of materials with a wide range of stiffness and density. This index has potential applications for optimal design in aerospace and other specialized engineering applications.

Thesis (Ph. D.)--University of Washington, 1997. / Vita. Includes bibliographical references (leaves [165]-173).