Ultra-Wideband (UWB) wireless communication systems employ large bandwidths and low transmitted power spectral densities, and are suitable for operation as underlay systems which reuse allocated spectrum. The subject of this dissertation is Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) UWB for high data-rate communication. We address four main questions: (1) What are the theoretical performance limits and practical system performance of MB-OFDM? (2) What extensions can be used to increase the system power efficiency and range? (3) Is it possible to estimate the system error rate without resorting to time-consuming simulations? and (4) What is the effect of interference from narrowband systems on MB-OFDM, and can this interference be mitigated? As for questions 1 and 2, we investigate the MB-OFDM performance, and propose system enhancements consisting of advanced error correcting codes and OFDM bit-loading. Our methodology includes the development of information-theoretic performance measures and the comparison of these measures with performance results for MB-OFDM and our proposed extensions, which improve the power efficiency by over 6 dB at a data rate of 480 Mbps. To address question 3, we develop novel analytical methods for bit error rate (BER) estimation for a general class of coded multicarrier systems (of which MB-OFDM is one example) operating over quasi-static fading channels. One method calculates system performance for each channel realization. The other method assumes Rayleigh distributed subcarrier channel gains, and leads directly to the average BER. Both methods are also able to account for sum-of-tones narrowband interference. As for question 4, we first present an exact analysis of the uncoded BER of MB-OFDM in the presence of interference from incumbent systems such as IEEE 802.16 ("WiMAX"). We also present a Gaussian approximation for WiMAX interference, and establish its accuracy through comparison with exact analysis and simulations. We then propose a two-stage interference mitigation technique for coded MB-OFDM, consisting of interference estimation during silent periods, followed by metric weighting during decoding, which provides substantial gains in performance in return for modest increases in complexity, and without requiring any modifications to the MB-OFDM transmitter.

Ultra-Wideband (UWB) wireless communication systems employ large bandwidths and low transmitted power spectral densities, and are suitable for operation as underlay systems which reuse allocated spectrum. The subject of this dissertation is Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) UWB for high data-rate communication. We address four main questions: (1) What are the theoretical performance limits and practical system performance of MB-OFDM? (2) What extensions can be used to increase the system power efficiency and range? (3) Is it possible to estimate the system error rate without resorting to time-consuming simulations? and (4) What is the effect of interference from narrowband systems on MB-OFDM, and can this interference be mitigated? As for questions 1 and 2, we investigate the MB-OFDM performance, and propose system enhancements consisting of advanced error correcting codes and OFDM bit-loading. Our methodology includes the development of information-theoretic performance measures and the comparison of these measures with performance results for MB-OFDM and our proposed extensions, which improve the power efficiency by over 6 dB at a data rate of 480 Mbps. To address question 3, we develop novel analytical methods for bit error rate (BER) estimation for a general class of coded multicarrier systems (of which MB-OFDM is one example) operating over quasi-static fading channels. One method calculates system performance for each channel realization. The other method assumes Rayleigh distributed subcarrier channel gains, and leads directly to the average BER. Both methods are also able to account for sum-of-tones narrowband interference. As for question 4, we first present an exact analysis of the uncoded BER of MB-OFDM in the presence of interference from incumbent systems such as IEEE 802.16 ("WiMAX"). We also present a Gaussian approximation for WiMAX interference, and establish its accuracy through comparison with exact analysis and simulations. We then propose a two-stage interference mitigation technique for coded MB-OFDM, consisting of interference estimation during silent periods, followed by metric weighting during decoding, which provides substantial gains in performance in return for modest increases in complexity, and without requiring any modifications to the MB-OFDM transmitter.

Ultra-Wideband (UWB) wireless communication systems employ large bandwidths and low transmitted power spectral densities, and are suitable for operation as underlay systems which reuse allocated spectrum. The subject of this dissertation is Multiband Orthogonal Frequency Division Multiplexing (MB-OFDM) UWB for high data-rate communication. We address four main questions: (1) What are the theoretical performance limits and practical system performance of MB-OFDM? (2) What extensions can be used to increase the system power efficiency and range? (3) Is it possible to estimate the system error rate without resorting to time-consuming simulations? and (4) What is the effect of interference from narrowband systems on MB-OFDM, and can this interference be mitigated? As for questions 1 and 2, we investigate the MB-OFDM performance, and propose system enhancements consisting of advanced error correcting codes and OFDM bit-loading. Our methodology includes the development of information-theoretic performance measures and the comparison of these measures with performance results for MB-OFDM and our proposed extensions, which improve the power efficiency by over 6 dB at a data rate of 480 Mbps. To address question 3, we develop novel analytical methods for bit error rate (BER) estimation for a general class of coded multicarrier systems (of which MB-OFDM is one example) operating over quasi-static fading channels. One method calculates system performance for each channel realization. The other method assumes Rayleigh distributed subcarrier channel gains, and leads directly to the average BER. Both methods are also able to account for sum-of-tones narrowband interference. As for question 4, we first present an exact analysis of the uncoded BER of MB-OFDM in the presence of interference from incumbent systems such as IEEE 802.16 ("WiMAX"). We also present a Gaussian approximation for WiMAX interference, and establish its accuracy through comparison with exact analysis and simulations. We then propose a two-stage interference mitigation technique for coded MB-OFDM, consisting of interference estimation during silent periods, followed by metric weighting during decoding, which provides substantial gains in performance in return for modest increases in complexity, and without requiring any modifications to the MB-OFDM transmitter. / Applied Science, Faculty of / Electrical and Computer Engineering, Department of / Graduate

No description available.

<p>Ultra Wideband Radio (UWB) is an upcoming alternative for wireless communications. Since the Federal Communication Commission in the USA allowed UWB for unlicensed usage in April 2002, more and more companies have started developing UWB systems. </p><p>The major difference with UWB compared to other RF systems is that UWB sends information with pulses instead of using a carrier wave. The technique is from the nineteenth century and was first developed by Heinrich Hertz (1857-1894), which led to transatlantic communications 1901. </p><p>This Master thesis presents a proposal of a transmitter for Ultra Wideband Radio using multiple bands. The proposed transmitter is implemented on system level in Simulink, Matlab. The frequency generation in the transmitter is also implemented at component level in a 0.13 um IBM process. The thesis begins with an introduction of UWB theory and techniques.</p>

Ultra Wideband Radio (UWB) is an upcoming alternative for wireless communications. Since the Federal Communication Commission in the USA allowed UWB for unlicensed usage in April 2002, more and more companies have started developing UWB systems. The major difference with UWB compared to other RF systems is that UWB sends information with pulses instead of using a carrier wave. The technique is from the nineteenth century and was first developed by Heinrich Hertz (1857-1894), which led to transatlantic communications 1901. This Master thesis presents a proposal of a transmitter for Ultra Wideband Radio using multiple bands. The proposed transmitter is implemented on system level in Simulink, Matlab. The frequency generation in the transmitter is also implemented at component level in a 0.13 um IBM process. The thesis begins with an introduction of UWB theory and techniques.

The presence of multipath propagation in indoor environments limits the performance of wideband radio communication systems and also the maximum data rate that can be feasible. This thesis addresses the dynamics of propagation mechanisms needed to design and exploit future broadband wireless local area networks in the 60GHz millimetre-wave band. The frequency band between 62-63GHz with data rates up to 155Mb/s, has been provisionally assigned for Mobile Broadband Systems. The main emphasis of this study was to provide an original contribution to the development, design and planning of future broadband communication systems using new high-resolution wideband channel measurement data. Based on this data, spatial and temporal statistics of several line-of-sight radio paths in a University campus are presented and analysed. In order to enable measurement of the wideband propagation characteristics a high-resolution (Ins) wideband Frequency-swept channel sounder was designed and implemented at 62.4GHz. The channel sounder has been built around a Vector Network Analyser to measure the complex transfer function of the channel. The instantaneous coherence bandwidth is found to be highly variable with the location of the receiver with respect to the base station. With delay spread values ranging from 20 to 70ns the coherence bandwidth remains most of the times below 10MHz. Based on the maximum delay spread of 68ns obtained in a 41m long narrow corridor, a BER of 10" 3 and normalised delay spread of 0.1, the minimum data transmission rate is estimated at 1.47 Mb/s. For a 12.80m room environment with maximum delay spread of 20ns the minimum data transmission rate is 5Mb/s. To achieve higher data transmission rates channel protection countermeasures appears to be necessary. However limiting the extent of a picocell size and utilising the potential capability of frequency re-use at 62.4GHz can result in radio network implementation without the complexity of countermeasures. Results relating to coherence bandwidth variability in multipath conditions confirm that higher user mobility envisaged for MBS would present a real challenge to the achievement of data transmission rates of the order of 155Mb/s. The research work reported in the thesis has been able to identify and extract from extensive high resolution wideband propagation the necessary design characteristics for the development of realistic radio planning models. Using measured results obtained in a number of radio paths geometries, the objectives of the project have been largely achieved and further work is recommended.

The state-of-the-art commercially available radio-frequency identification (RFID) transponders are usually composed of an antenna and an application specific integrated circuit chip, which still makes them very costly compared to the well-established barcode technology. Therefore, a novel low-cost RFID system solution based on passive chipless RFID transponders manufactured using conductive strips on flexible substrates is proposed in this work. The chipless RFID transponders follow a specific structure design, which aim is to modify the shape of the impinged electromagnetic wave to embed anidentification code in it and then backscatter the encoded signal to the reader. This dissertation comprises a multidisciplinary research encompassing the design of low-cost chipless RFID transponders with a novel frequency coding technique, unlike usually disregarded in literature, this approach considers the communication channel effects and assigns a unique frequency response to each transponder. Hence, the identification codes are different enough, to reduce the detection error and improve their automatic recognition by the reader while working under normal conditions. The chipless RFID transponders are manufactured using different materials and state-of-the-art mass production fabrication processes, like printed electronics. Moreover, two different reader front-ends working in the ultra-wideband (UWB) frequency range are used to interrogate the chipless RFID transponders. The first one is built using high-performance off-theshelf components following the stepped frequency modulation (SFM) radar principle, and the second one is a commercially available impulse radio (IR) radar. Finally, the two readers are programmed with algorithms based on the conventional minimum distance and maximum likelihood detection techniques, considering the whole transponder radio frequency (RF) response, instead of following the commonly used approach of focusing on specific parts of the spectrum to detect dips or peaks. The programmed readers automatically identify when a chipless RFID transponder is placed within their interrogation zones and proceed to the successful recognition of its embedded identification code. Accomplishing in this way, two novel fully automatic SFM- and IRRFID readers for chipless transponders. The SFM-RFID system is capable to successfully decode up to eight different chipless RFID transponders placed sequentially at a maximum reading range of 36 cm. The IR-RFID system up to four sequentially and two simultaneously placed different chipless RFID transponders within a 50 cm range.:Acknowledgments Abstract Kurzfassung Table of Contents Index of Figures Index of Tables Index of Abbreviations Index of Symbols 1 Introduction 1.1 Motivation 1.2 Scope of Application 1.3 Objectives and Structure Fundamentals of the RFID Technology 2.1 Automatic Identification Systems Background 2.1.1 Barcode Technology 2.1.2 Optical Character Recognition 2.1.3 Biometric Procedures 2.1.4 Smart Cards 2.1.5 RFID Systems 2.2 RFID System Principle 2.2.1 RFID Features 2.3 RFID with Chipless Transponders 2.3.1 Time Domain Encoding 2.3.2 Frequency Domain Encoding 2.4 Summary Manufacturing Technologies 3.1 Organic and Printed Electronics 3.1.1 Substrates 3.1.2 Organic Inks 3.1.3 Screen Printing 3.1.4 Flexography 3.2 The Printing Process 3.3 A Fabrication Alternative with Aluminum or Copper Strips 3.4 Fabrication Technologies for Chipless RFID Transponders 3.5 Summary UWB Chipless RFID Transponder Design 4.1 Scattering Theory 4.1.1 Radar Cross-Section Definition 4.1.2 Radar Absorbing Material’s Principle 4.1.3 Dielectric Multilayers Wave Matrix Analysis 4.1.4 Frequency Selective Surfaces 4.2 Double-Dipoles UWB Chipless RFID Transponder 4.2.1 An Infinite Double-Dipole Array 4.2.2 Double-Dipoles UWB Chipless Transponder Design 4.2.3 Prototype Fabrication 4.3 UWB Chipless RFID Transponder with Concentric Circles 4.3.1 Concentric Circles UWB Chipless Transponder 4.3.2 Concentric Rings UWB Chipless RFID Transponder 4.4 Concentric Octagons UWB Chipless Transponders 4.4.1 Concentric Octagons UWB Chipless Transponder Design 1 4.4.2 Concentric Octagons UWB Chipless Transponder Design 2 4.5 Summary 5. RFID Readers for Chipless Transponders 5.1 Background 5.1.1 The Radar Range Equation 5.1.2 Range Resolution 5.1.3 Frequency Band Selection 5.2 Frequency Domain Reader Test System 5.2.1 Stepped Frequency Waveforms 5.2.2 Reader Architecture 5.2.3 Test System Results 5.3 Time Domain Reader 5.3.1 Novelda Radar 5.3.2 Test System Results 5.4 Summary Detection of UWB Chipless RFID Transponders 6.1 Background 6.2 The Communication Channel 6.2.1 AWGN Channel Modeling and Detection 6.2.2 Free-Space Path Loss Modeling and Normalization 6.3 Detection and Decoding of Chipless RFID Transponders 6.3.1 Minimum Distance Detector 6.3.2 Maximum Likelihood Detector 6.3.3 Correlator Detector 6.3.4 Test Results 6.4 Simultaneous Detection of Multiple UWB Chipless Transponders 6.5 Summary System Implementation 7.1 SFM-UWB RFID System with CR-Chipless Transponders 7.2 IR-UWB RFID System with COD1-Chipless Transponders 7.3 Summary Conclusion and Outlook References Publications Appendix A RCS Calculation Measurement Setups Appendix B Resistance and Skin Depth Calculation Appendix C List of Videos Test Videos Consortium Videos Curriculum Vitae