The dissertation is concerned with a problem of condensing boilers. The attention will apply to the condensing boiler which is filled in an absortion springle for a better an-nealing of exhaust gas. On this account the dissertation is possible to divide by some parts. There is a generally resolution of a condensing boiler´s principle and an effective annealing of exhaust gas for low temperatures in the first part. A description of an ab-sorption circulation follows in the second part. A practical part solves a suggestion of the condensing boiler with an absorption afterheat removal springle, an assesment of working parameters and a calculation of heat transfer surfaces. A technoeconomic ana-lysis of a proposed arrangement is made in the final part.

The thesis contains calculations of a boiler burning natural gas. For designated values of steam pressure, temperature and steam power is made a proportion design and heat calculations.

This diploma thesis describes the design of steam boiler for combustion natural gas, which has a steam power 80t/hour. In the first phase is performed calculation of stoichiometric amount of combustion air and flue gas. After that follows constructional proposal of the combustion chamber. Furthermore continue by calculation heating surfaces of the boiler. In conclusion, the thesis is focused on designing the injections. To check the accuracy of the results is recalculated heat balance the whole boiler.

In this work, there is an overview of the design concept of condensing boilers and types of heat pumps. The current state of heating in company is assessed and possible variants are given for techno-economic evaluation. For boiler room with the gas boiler is prepared a proposal with condensation boiler. For parameters are designed and calculated proposals to form a condensing boiler. The end of the work is focused on the advantages of gas boiler and heat pump.

This master's thesis informs its reader about actual energetical situation of Poland and its probable future. The thesis focus on shale gas resesources in the world and Poland and methods of its mining and procesing. Main problematics of determining, designing and technology of TEG dehydration unit were described in this thesis.

This master´s thesis is dealing with the thermal calculation and design of boilers for natural gas combustion. The aim is to design the heating surfaces, so as to meet the requirements of the steam temperature of 490 ° C, the pressure of 7 MPa and the steam output of 60 t/h.

This thesis deals with the fuel change for hot water boilers with wattage of 116.3 MW. At first a stoichiometric calculation is drawn. Calculation of pressure loss in pipeline follows. Consequential part elaborates on calculation of parallel connected heating surfaces following with a draft of regenerative air heater Ljungtröm. Conclusively, a calculation is carried out to verify the functionality of the serial connection of the heating surfaces.

This master thesis deals with problems of determining operational and safety risks at gas boiler room in office building with total output of 4×49 kW. The gas boiler room is equipped with four boilers Geminox THRi 10-50. The aim of this master thesis is to determine the potential operational and safety risks of gas boiler room. The master thesis is divided into several parts, when the first part is describing the current situation with some theoretical knowledge and risk analysis. This part also outlines possible solutions for identification and quantification of risks to the gas boiler room. The specific risk factors are determined at other part of master thesis and there is also their analysis, which is solved by cause and effect diagram and by Failure Mode and Effect Analysis. The specific precautions are suggested for chosen risks in final part of master thesis.

The theoretical findings about methods of earth faults indication are elaborated in this thesis into form, which is applicable to design contactless indicator of failure states on MV lines. This design contains electromagnetic field sensors, evaluation device and software support. The higher effectiveness of clearing of fault and better health and asset protection is supposed by using of these indicators.

The aim of the Diploma Thesis is to discuss the design and construction solution for circulation of the thermodynamic heat pump especially used in the heating industry with stoichiometric combustion of chosen natural gas. The basic components of the proposed heat pump are turbine, compressor and gearbox. To solve the presented aims, the thermodynamic calculation of the individual components, the determination of the efficiency of the whole equipment and the analysis of the physical properties of the natural gas with regard to the specified input and output parameters were considered. In addition, an analysis of the individual components design of the proposed equipment was carried out, on the basis the technically most acceptable variant was chosen and the equipment construction was carried out incl. connecting elements. Drawing documentation is part of the attachments. On the basis of the analysis, it can be stated that the proposed plant leads to energy savings, is ecologically sufficient and has been shown to have approximately twice the amount of heat dissipated than without its use.