Low cost silicates with apatite-structure (general formula of apatite A10-xM6O26±δ, where A = rare earth or alkaline earth and M= Si, Ge, P, V..) have been proposed recently as promising solid electrolyte materials (oxygen ion conductors) for use at intermediate temperature solid oxide fuel cells (SOFCs). These materials exhibit sufficiently high ionic conductivity (e.g. ~ 0.01 S cm-1 at 700 oC), which is dominated by the interstitial site mechanism and can exceed that of yttria-stabilized-zirconia (YSZ), the solid electrolyte used in state-of-the-art SOFCs. The apatite structure is tolerant to extensive aliovalent doping, which has been applied for improving ionic conductivity. In this work are presented results concerning synthesis, conductivity and catalytic characterization of Fe- and/or Al-doped apatite type lanthanum silicates (ATLS) of the general formula La10-zSi6-x-yAlxFeyO26±δ as well as electrochemical characterization of interfaces of ATLS pellets with perovskite and Ni-based electrodes. The aim was to investigate the properties of these ATLS material, in particular as it concerns their potential use as SOFC components or as catalysts in oxidation reactions.
The conductivity of pellets prepared from ATLS powders synthesized via four different methods and having different grain size was measured under air and at different temperatures in the range 600 -850 oC, aiming to identification of the effect of composition (doping), method of synthesis, grain size and pellet sintering conditions. For electrolytes of the same composition, those prepared via mechanochemical activation exhibited the highest conductivity, which was improved with increasing Al- and decreasing Fe-content.
In state-of-the-art SOFCs perovskite electrodes are used as cathodes and Ni-based electrodes as anodes, thus electrochemical characterization of perovskite and Ni-based/ATLS interfaces was carried out. As it concerns perovskite/ATLS interfaces, the characterization focused on the study of the open circuit AC impedance characteristics of a La0.8Sr0.2Ni0.4Fe0.6O3-δ/La9.83Si5Al0.75Fe0.25O26±δ interface, at temperatures 600 to 800 oC and oxygen partial pressures ranging from 0.1 to 20 kPa. Under the aforementioned conditions, it was observed that the impedance characteristics of the interface were determined by at least two different processes, corresponding to two partially overlapping depressed arcs in the Nyquist plots. The polarization conductance of the interface was found to increase with increasing temperature as well as with increasing oxygen partial pressure, following a power law dependence. The electrochemical characterization of Ni-based electrodes/ATLS interfaces involved study of the electrochemical characteristics of NiO-apatite cermet electrodes as well as a Ni sputtered electrode interfaced with Al- or Fe-doped apatite electrolytes, under hydrogen atmospheres. The impedance characteristics of these electrodes were found to be determined by up to three different processes, their relative contribution depending on the electrode microstructure, Ni content (as it concerns the cermet electrodes), temperature, hydrogen partial pressure and applied overpotential.
Aiming to investigation of potential catalytic properties of ATLS materials the catalytic activity for CO combustion of a series of ATLS powders was studied. For this purpose, two series of apatite-type lanthanum silicates La10-xSi6-y-zAlyFezO27-3x/2-(y+z)/2 (ATLS), undoped or doped with Al and/or Fe, were synthesized via sol-gel and modified dry sol-gel methods and tested as catalysts for CO combustion. The experiments revealed that the ATLS powders were catalytically active for CO combustion above approximately 300 oC, with light-off temperatures T50 (50% conversion of CO) ranging from 505 to 629 oC. The study focused on the effect on catalytic activity of the synthesis method and doping with Al and/or Fe. Non-doped ATLS with stoichiometric structure, namely La10Si6O27 prepared via the sol-gel method, exhibited the highest catalytic activity for CO oxidation among all tested compositions, the comparison being based on the measured catalytic rate (expressed per surface area of the catalyst) under practically differential conditions. Compared to La-Sr-Mn-O and La-Sr-Co-Fe-O perovskite powders, the tested ATLS powders exhibited lower catalytic activity for CO oxidation. / -
| Identifer | oai:union.ndltd.org:upatras.gr/oai:nemertes:10889/5563 |
| Date | 01 October 2012 |
| Creators | Gasparyan, Hripsime |
| Contributors | Μπεμπέλης, Συμεών, Μπεμπέλης, Συμεών, Μπογοσιάν, Σογομών, Νικολόπουλος, Παναγιώτης, Νεοφυτίδης, Στυλιανός, Κουτσούκος, Πέτρος, Κονταρίδης, Δημήτριος, Κατσαούνης, Αλέξανδρος |
| Source Sets | University of Patras |
| Language | English |
| Detected Language | English |
| Type | Thesis |
| Rights | 0 |
| Relation | Η ΒΚΠ διαθέτει αντίτυπο της διατριβής σε έντυπη μορφή στο βιβλιοστάσιο διδακτορικών διατριβών που βρίσκεται στο ισόγειο του κτιρίου της. |
Page generated in 0.0026 seconds