One of the major challenges in earth sciences and mineral exploration has been to determine with high accuracy and at a fast rate the elemental composition as well as the general chemistry of a rock sample. Many analytical techniques e.g., scanning electron microscopy (SEM) have been employed in the past with a certain degree of success, but their analyses usually require a lengthy sample preparation and time-consuming measurements which produce results at a much slower rate than techniques whichrequire less or do not require any sample preparation at all. SEM images the surface of a sample by scanning it with a high-energy beam of electrons in a raster scan pattern, where the primary electron beam produced under very low air pressure vacuum scans across the sample by striking it, and a variation of signals produce an image of the surface, or its elemental composition together with energy dispersive X-rays. Alternatively, laser induced breakdown spectrometry (LIBS) and multi energy X-ray transmission (ME-XRT) are non-contact measurement scanning techniques, capable of producing faster results than SEM-EDS which makes them suitable for real time measurements and analyses as they do not slow down the pace of a project being carried out. LIBS is a spectroscopic technique used to characterize and detect materials where a highly energetic laser pulse is focused onto the surfaces of solids, liquids or gases resulting in atomic and molecular species to emit light at specific wavelengths which is collected with a spectrometer and analysed using a computer. Comparably, ME-XRT is a sensor-based sorting technique involving the planar projection of X-ray attenuation of a particle stream, distributed on a fast conveyor belt, where they are scanned and evaluated while passing and an image is recorded by a line scan detector. Eleven rock samples were analysed in this study. They include four rock type samples: granite, basalt, sandstone, and gneiss, all obtained from Luleå University of Technology (LTU) sample storage and seven ore type samples which include a porphyry Cu sulphide ore, a porphyry Cu oxide ore, a porphyry Cu-Au-Ag ore, an apatite iron ore (AIO), an iron-oxide copper gold ore (IOCG), an orogenic gold ore and a volcanogenic massive sulphide ore (VMS). The SEM results give a semi-quantitative elemental composition of the rocks, which may be usedto discriminate mineralisation. Energy dispersive X-ray spectroscopy (EDS) maps may be used to identifygeological features and secondary electron (SE) images may be used to understand the topography of the rock samples. The SEM has a low penetration depth rate but produces moderate to high accuracy resultsdepending on the settings and calibrations. It requires a lengthy sample preparation, and its analytical time is often too long for routine industrial application. LIBS results also provide rock elemental compositions similar to the SEM, which may be quantitative if the same spectrometer is used for all elements and calibrated against a standard. It also produces element maps similar to the SEM-EDS maps. LIBS analyses yield high accuracy results but at a low penetration depth. There are no standard calibrations for the LIBS measurements, which limits quantification. LIBS measurements do not require any form of sample preparation. ME-XRT analyses result in rock chemical data portraying a light material fraction (aluminium-like) and a heavy material fraction (iron-like) which may be used to distinguish different rock samples based on the closeness of their effective atomic number Zeff to that of aluminium and iron respectively. It’s analysis also produces low-resolution images of the analysed rock samples. The image resolution is too low to allow interpretation of the data in the context of the structures and textures in the rock samples. It has a higher penetration depth than LIBS and SEM-EDS producing more volumetric data but with a lower accuracy in terms of the amount of information obtained. Only two elements are used for ME-XRT calibration measurements, if many elements of varying atomic numbers could be used, it would have the ability to provide a more reliable data. Samples must have a maximum and minimum thickness; thus, sample preparation is required to regulate the rock thickness. SEM and LIBS provide element compositions of minerals and element distribution maps required by geologist in their daily activities during exploration and mining. This information can be considered the most useful obtained from all three techniques. However, LIBS analyses are faster, and its maps are of higher quality even at the same resolution as the SEM-EDS. This makes the LIBS preferable for real time measurements and analyses. Geological activities like drill core logging, mine mapping and sampling for grade control all require fast results for project continuity and LIBS is suitable for this purpose as it can keep up with the pace of these activities. SEM analytical technique provides semi-quantitative data which is more accurate than the LIBS data and thus, preferable for usage in research institutions and universities.ME-XRT can reveal information on the internal structures or different rock sample compositions. This makes it a suitable technique in distinguishing ore from waste material especially in iron ore mining and processing where the iron needs to be separated from the siliceous waste and sorting is also required prior to beneficiation to avoid equipment destruction by abrasive quartz. LIBS and ME-XRT analytical techniques complement each other in terms of analytical capabilities as LIBS has a low penetration depthrate but high accuracy results while the ME-XRT has a high penetration depth rate but low accuracy results. They are both fast scanning techniques that can be used for real time measurements and analyses and if their analytical prowess can be improved, the combination of these two fast analytical techniques may enable us to obtain high quality data and may as well be what is needed by geologists in the future.
| Identifer | oai:union.ndltd.org:UPSALLA1/oai:DiVA.org:ltu-90080 |
| Date | January 2022 |
| Creators | Elvis Nkioh, Nsioh |
| Publisher | Luleå tekniska universitet, Geovetenskap och miljöteknik |
| Source Sets | DiVA Archive at Upsalla University |
| Language | English |
| Detected Language | English |
| Type | Student thesis, info:eu-repo/semantics/bachelorThesis, text |
| Format | application/pdf |
| Rights | info:eu-repo/semantics/openAccess |
Page generated in 0.0026 seconds