<p>Heat dissipation requirements of next-generation power electronics in electric vehicles, high-performance computing, and radar systems will far exceed the capabilities of conventional heat sink technologies such as single-phase liquid cold plates and air-cooled heat sinks. The leading candidate technology that promises to meet these needs is microchannel flow boiling. Compared to conventional heat sink technologies, flow boiling provides some of the highest heat transfer coefficients available and can dissipate heat at a lower pumping power and with more uniform surface temperatures. However, there are unique challenges associated with flow boiling that currently prevent practical implementation of the technology, including limited modeling capabilities, inherent critical heat flux (CHF) limitations, and the presence of two-phase flow instabilities. This thesis is targeted primarily at addressing the impact of dynamic two-phase flow instabilities on heat transfer and CHF in microchannel heat sinks, in contrast with earlier literature that has focused on prediction and characterization of the flow dynamics.</p>
<p><br></p>
<p>Two dynamic instabilities of importance in microchannel heat sinks are pressure drop oscillations (PDO) and parallel channel instabilities, both resulting from an interaction between the inertia of a two-phase mixture within a heated channel and a source of compressibility outside of the channel. However, the individual impact of these instabilities on heat transfer performance has not been quantified. In this thesis, an experimental facility is developed to isolate the individual and combined impact of PDOs and parallel channel instabilities on surface temperature and CHF in single- and parallel-microchannels. This is achieved by introducing a measurable compressible volume directly upstream of the test section and isolating the test section from any unwanted compressibility within components throughout the rest of the system. Experiments are first performed targeting the investigation of PDOs in single channels and then targeting PDOs and parallel channel instabilities in multi-channel heat sinks. In the case of parallel channels, inlet restrictors are introduced to suppress channel-to-channel interactions and provide a baseline case of stable boiling. Throughout these experiments, only moderate increases in time-average surface temperature are observed (6 °C) and reduction of CHF is negligible, despite drastically different flow pattern observations when instabilities are present. These observations are in stark contrast with other cases in the literature, for which significant deterioration of surface temperatures and CHF have been attributed to the presence of PDOs. For example, significant temperature oscillations have been observed in the literature studying silicon-etched microchannel heat sinks experiencing PDOs. A predictive model is clearly required to understand and detect the conditions when dynamic instabilities should be considered in heat sink design.</p>
<p><br></p>
<p>To better understand the conditions when PDOs might have significant impact on heat transfer performance, an investigation of thermal capacitance is performed using a dynamic two-phase model and a targeted experimental approach in heat sinks having different thermal masses. The model reveals that, if thermal capacitance is low, PDOs become more severe, and the amplitude of temperature oscillations increase. These predictions are confirmed by experimental observations, and, in addition, premature CHF is observed in the heat sink with lower thermal mass. With sufficient thermal capacitance, the system recovers before triggering CHF, preventing deterioration of performance due to PDOs. Among the wide range of flow conditions considered in this thesis, the reduction of thermal mass resulted in the greatest impact on transient response of a heat sink during flow boiling instabilities. This reveals thermal capacitance as a critical parameter when determining if dynamic instabilities will deteriorate performance in a microchannel heat sink application. This allows engineers to make an informed judgement on whether adding features to suppress instabilities, at the cost of increased pumping power, is warranted. In order for the practical implementation of two-phase heat sinks to be realized, further development of dynamic modeling capabilities is required, and these models should be backed by systematic experimental investigations into conditions where instabilities should be considered.</p>
| Identifer | oai:union.ndltd.org:purdue.edu/oai:figshare.com:article/20338668 |
| Date | 19 July 2022 |
| Creators | Matthew D Clark (13118526) |
| Source Sets | Purdue University |
| Detected Language | English |
| Type | Text, Thesis |
| Rights | CC BY 4.0 |
| Relation | https://figshare.com/articles/thesis/THE_IMPACT_OF_FLOW_BOILING_INSTABILITIES_ON_HEAT_TRANSFER_IN_MICROCHANNEL_HEAT_SINKS/20338668 |
Page generated in 0.002 seconds