Return to search

Radiation damage in GaAs and SiC

In this dissertation the microstructure and hardness of phosphorous implanted SiC and neutron irradiated SiC and GaAs have been investigated. SiC is important due to its application as a barrier coating layer in coated particle fuel used in high temperature gas cooled reactors. The characterisation of neutron irradiated GaAs has been included in this study in order to compare the radiation damage produced by protons and neutrons since proton bombardment of SiC could in principle be used for out-of-reactor simulations of the neutron irradiation damage created in SiC during reactor operation. The following SiC and GaAs compounds were investigated: As-implanted and annealed single crystal 6H-SiC wafers and polycrystalline 3C-SiC bulk material implanted with phosphorous ions. As-irradiated and annealed polycrystalline 3C-SiC bulk material irradiated with fast neutrons. As-irradiated and annealed single crystal GaAs wafers irradiated with fast neutrons. The main techniques used for the analyses were transmission electron microscopy (TEM) and nano-indentation hardness testing. The following results were obtained for the investigation of implanted and irradiated SiC and GaAs: Phosphorous Implanted 6H-SiC and 3C-SiC The depth of the P+ ion damage was found to be in good agreement with predictions by TRIM 2010. Micro-diffraction of the damage region in P+ implanted 6H-SiC (dose 5×1016 ions/cm2) indicates that amorphization occurred and that recrystallisation of this layer occurred during annealing at 1200°C. TEM analysis revealed that the layer recrystallised in the 3C phase of SiC and twin defects also formed within the layer. Micro-diffraction of the damage region in P+ implanted 3C-SiC (dose 1×1015 ions/cm2) indicates that amorphization also occurred for this sample and that recrystallisation of this layer occurred during annealing at 800°C. Nano-hardness testing of the P+ implanted 6H-SiC indicated that the hardness of the implanted SiC was initially much lower than unimplanted SiC due to the formation of an amorphous layer during ion implantation. After annealing the implanted SiC at 800°C and 1200°C, the hardness increased due to re-crystallisation and point defect hardening. Neutron Irradiated 3C-SiC TEM investigations of neutron irradiated 3C-SiC revealed the presence dark spot defects for SiC samples irradiated to a dose of 5.9×1021 n/cm2 and 9.6×1021 n/cm2. Neutron Irradiated GaAs TEM investigation revealed a high density of dislocation loops in the unannealed neutron irradiated GaAs. The loop diameters increased after post-irradiation annealing in the range 600 to 800 °C. The dislocation loops were found to be of interstitial type lying on the {110} cleavage planes of GaAs. This finding is in agreement with earlier studies on 300 keV proton bombarded and 1 MeV electron irradiated GaAs where interstitial loops on {110} planes became visible after annealing at temperatures exceeding 500 °C. The small dislocation loops on the {110} planes of the neutron irradiated GaAs transformed to large loops and dislocations after annealing at 1000 °C.

Identiferoai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:nmmu/vital:10515
Date January 2011
CreatorsJanse van Vuuren, Arno
PublisherNelson Mandela Metropolitan University, Faculty of Science
Source SetsSouth African National ETD Portal
LanguageEnglish
Detected LanguageEnglish
TypeThesis, Masters, MSc
Format161 p, pdf
RightsNelson Mandela Metropolitan University

Page generated in 0.0022 seconds