Ph.D. / A one-dimensional numerical simulation of photovoltaic (PV) cells has been written, and has been designated RAUPV2. An algorithm for determining the optical generation rate profile, taking into account multiple internal reflections in a multilayer cell has been developed. A method which enables realistic boundary values to be calculated, using RAUPV2 itself, has been developed. This method allows all three boundary values (', Fn and Fp) at each surface, to be determined, without the need to specify any additional input parameters. A comprehensive set of input parameters for aSi:H PV cells has been established, in consultation with the literature. Dangling-bond theory has been described and input parameters for dangling-bond defects have been presented. The effect of surface states in the p-layer on the contact potential at the TCO/p interface has been investigated. It was found that there is an intimate relationship between the contact potential and the parameters pertaining to the surface states. A simple method has been demonstrated, which has allowed RAUPV2 to reproduce the J-V curve of an existing aSi:H PV cell. The method requires that only the dangling-bond concentration in the i-layer and the contact potential at the Sn02/P interface needs to be adjusted. Once the J- V curve had been generated, the simulation results were used to characterise the empirical cell, in both thermodynamic- and steady-state equilibrium. This simulated cell was designated the realistic cell. The effect of asymmetries in the input parameters, under carrier band mobility interchange, on the performance of p-i-n cells has been investigated. The results indicate that, while asymmetries in the gap state distributions do give rise to asymmetrical behaviour in the J- V curve, the effect is slight, and it is the positional asymmetry of the optical generation profile that is mostly responsible for the observed asymmetry in the J- V curve under mobility interchange. An investigation of the limiting carrier effect has led to the conclusion that, in a p-i-n aSi:H cell under forward bias, the electron is the limiting carrier. This has been explained by appealing to the form of the optical generation profile, since most electron-hole pairs (EHPs) are generated near the front of the cell, and it is electrons that must be collected at the back contact. Investigations of the n-i-p aSi:H cell, under forward bias, have shown the hole to be the limiting carrier. It was found that the introduction of positional symmetry into the optical generation rate profile greatly reduced the limiting carrier effect, and it was concluded that the limiting carrier effect arises due to the asymmetries in the material parameters of the cell, particularly the _ positional asymmetry of the optical generation profile. It was observed that the nature of the optical generation profile actually plays an important role in determining the identity of the limiting carrier, in a p-i-n cell. The same effect was not observed in the n-i-p cell. The effective carrier collection length has been defined, and it was seen that the limiting carrier possesses the larger effective collection length. The effect of boron and phosphorous profiling of the i-layer was studied. It was found that boron profiling led to a decrease in cell performance, while phosphorous profiling improved cell performance. It was found that there was a P concentration at which cell performance peaked. The dependence of the spectral response of the realistic cell on device length L, was investigated, showing a general improvement in the spectral response as L was decreased. The spectral response has been interpreted in a novel way. It was assumed that the form of the monochromatic optical generation profiles in the vicinity of the peak in the spectral response represented optimal generation profiles. These profiles were subjected to a linear transformation, such that their form was preserved but that their integrated value was the same as that of the realistic optical generation profile, under global AM1.5 illumination. Using these transformed optical generation profiles, J- V curves were obtained. The maximum power output PM of these J- V curves was seen to exhibit a maximum some 17% greater than that of the realistic cell with a realistic optical generation profile. The spectral response of the phosphorous profiled cell was obtained. In a manner similar to that for the non-P profiled cell, the optimal generation profile was found. The PM for this profile was found to be 7.86mWcm -2 , considerably larger than the 5.60mWcm-2 for the phosphorous profiled cell with a realistic optical generation profile. The effect on the simulation output of variations in numerous dangling-bond defect input parameters has been investigated. It was found that the energy position and concentration of the doped layer defects need not be known to a high degree of precision. On the other hand, it was found that the energy position of the i-layer defects, the standard deviation of the defect distributions, and the defect carrier capture cross-sections, do need to be known with certainty.
| Identifer | oai:union.ndltd.org:netd.ac.za/oai:union.ndltd.org:uj/uj:3172 |
| Date | 27 August 2012 |
| Creators | Prentice, Justin Steven Calder |
| Source Sets | South African National ETD Portal |
| Detected Language | English |
| Type | Thesis |
Page generated in 0.0012 seconds