In this thesis, modeling and electrical characterization have been performed on Cu(In,Ga)Se2 (CIGS) and Cu2ZnSnS4 (CZTS) thin film solar cells, with the aim to investigate potential improvements to power conversion efficiency for respective technology. The modeling was primarily done in SCAPS, and current-voltage (J-V), quantum efficiency (QE) and capacitance-voltage (C-V) were the primary characterization methods. In CIGS, models of a 19.2 % efficient reference device were created by fitting simulations of J-V and QE to corresponding experimental data. Within the models, single and double GGI = Ga/(Ga+In) gradients through the absorber layer were optimized yielding up to 2 % absolute increase in efficiency, compared to the reference models. For CIGS solar cells of this performance level, electron diffusion length (Ln) is comparable to absorber thickness. Thus, increasing GGI towards the back contact acts as passivation and constitutes largest part of the efficiency increase. For further efficiency increase, majority bottlenecks to improve are optical losses and electron lifetime in the CIGS. In a CZTS model of a 6.7 % reference device, bandgap (Eg) fluctuations and interface recombination were shown to be the majority limit to open circuit voltage (Voc), and Shockley-Read-Hall (SRH) recombination limiting Ln and thus being the majority limit to short-circuit current and fill-factor. Combined, Eg fluctuations and interface recombination cause about 10 % absolute loss in efficiency, and SRH recombination about 9 % loss, compared to an ideal system. Part of the Voc-deficit originates from a cliff-type conduction band offset (CBO) between CZTS and the standard CdS buffer layer, and the energy of the dominant recombination path (EA) is around 1 eV, well below Eg for CZTS. However, it was shown that the CBO could be adjusted and improved with Zn1-xSnxOy buffer layers. Best results gave EA = 1.36 eV, close to Eg = 1.3-1.35 eV for CZTS as given by photoluminescence, and the Voc-deficit decreased almost 100 mV. Experimentally by varying the absorber layer thickness in CZTS devices, the efficiency saturated at <1 μm, due to short Ln, expected to be 250-500 nm, and narrow depletion width, commonly of the order 100 nm in in-house CZTS. Doping concentration (NA) determines depletion width, but is critical to device performance in general. To better estimate NA with C-V, ZnS and CZTS sandwich structures were created, and in conjunction with simulations it was seen that the capacitance extracted from CZTS is heavily frequency dependent. Moreover, it was shown that C-V characterization of full solar cells may underestimate NA greatly, meaning that the simple sandwich structure might be preferable in this type of analysis. Finally, a model of the Cu2ZnSn(S,Se)4 was created to study the effect of S/(S+Se) gradients, in a similar manner to the GGI gradients in CIGS. With lower Eg and higher mobility for pure selenides, compared to pure sulfides, it was seen that increasing S/(S+Se) towards the back contact improves efficiency with about 1 % absolute, compared to the best ungraded model where S/(S+Se) = 0.25. Minimizing Eg fluctuation in CZTS in conjunction with suitable buffer layers, and improving Ln in all sulfo-selenides, are needed to bring these technologies into the commercial realm.
Identifer | oai:union.ndltd.org:UPSALLA1/oai:DiVA.org:uu-320308 |
Date | January 2017 |
Creators | Frisk, Christopher |
Publisher | Uppsala universitet, Fasta tillståndets elektronik, Uppsala |
Source Sets | DiVA Archive at Upsalla University |
Language | English |
Detected Language | English |
Type | Doctoral thesis, comprehensive summary, info:eu-repo/semantics/doctoralThesis, text |
Format | application/pdf |
Rights | info:eu-repo/semantics/openAccess |
Relation | Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, 1651-6214 ; 1514 |
Page generated in 0.0365 seconds