To build multi story buildings out of timber is of a common interest in the building sector. Timber as a building material has many profits, such as the low cost, the availability and the ability to recycle it, the low carbon footprint and the workability. Although, when it comes to fire protection of buildings with a timber based structure there are challenges regarding prevention of the spread of fire while timber surface is exposed to fire. There have been cases in which timber buildings have caught fire leading to severe fire spread and ruined buildings. One example concerns a student modulus accommodation in Luleå that caught fire in august 2013. The fire started on the fourth floor after which a vertical fire spread occurred in concealed spaces between the volume modules. According to the fire investigation lack of knowledge regarding performance of detailed building solutions has led to the poor fire performance of the building. This master thesis mainly consists of a model scale tests that is prepared and performed according to the standard EN 1363-1. The purpose of the test is to investigate the performance of various cavity barriers exposed to fire. The main objective is to examine which temperatures that can be expected at different positions at various cavity barriers when using model scale test as a test method. There are two main kinds of cavity barriers: barriers that are airtight and closed inside the voids of the construction; and ventilated barriers. The most common cavity barriers are the ones that are airtight and closed. The material can be solid wood, gypsum board or mineral wool. The installation areas for these cavity barriers are anywhere, besides where the concealed spaces shall be ventilated and in every joint that shall be sealed using sealant. The ventilated cavity barriers are mounted in concealed spaces where the ventilating function is provided. These concealed spaces are often situated in, for example, ventilated attics, facades and roofs. The purpose of the ventilated barriers is to maintain the air flow in the cavity during regular conditions but also to form a protecting barrier between fire compartments when exposed to fire. The model scale test includes test apparatuses such as thermocouples and a fire resistance furnace with plate thermometers and burners. In addition, a test rig consisting of test specimens and the products to be tested are essential. In this report, two model scale tests have been performed and prepared according to EN 1363‑1. The test period endured for four hours and the thermocouples measured the temperatures during the whole time. During the first hour the test specimens were exposed to the standard ISO 834 fire curve by controlling the burners in the furnace. After one hour the burners were turned off and the specimens were no longer exposed to fire. The measurements of the temperatures continued during three more hours. After the first two of these three hours the furnace was opened to confer more oxygen in the purpose to record any changes in the temperatures. Results of the performed experiments have indicated parameters that affect the performance of the cavity barriers. The cavity surface itself has an influence to the fire spread. The number of barriers in the cavity and the material properties of the material that is used as the cavity barrier lead to the different protection by those cavity barriers. Some of the tested barriers were plastic covered, which had effect on the performance of the cavity barriers. The dimensions of the barriers, moreover the width and the thickness, are important parameters for the proper function of the barrier. The test results indicate that glowing combustion occurs in the cavity between various cavity barriers. It can be seen that the temperature rises when the furnace is opened. This indicates the appearance of smouldering since the combustion increases when the amount of oxygen increases, which leads to a temperature rise. Furthermore, the appearance of smouldering (glowing combustion) can be indicated by the observation of the damages of the specimens after the test. The temperatures that may be expected at the unexposed side of the cavity barrier depend on the surface material of the cavity, dimensions, and the material of the cavity barriers. Smouldering is a consequence of the temperature rise in closed cavities between cavity barriers. The performed test endured for approximately four hours and this indicates that fires in cavities can stay for a long time. To ensure the performance of various cavity barriers and verification by a model scale test it is important to perform further experiment and analyses to investigate the effects of the various parameters. To ensure the effectiveness of the performance of the cavity barriers they should be tested in cavities with various widths and various heights. Further investigation of the risk for smouldering is needed with measuring the amount of oxygen and the pressure.
| Identifer | oai:union.ndltd.org:UPSALLA1/oai:DiVA.org:ltu-63648 |
| Date | January 2017 |
| Creators | Gustafsson, Sara, Jonsson, Stina |
| Publisher | Luleå tekniska universitet, Institutionen för samhällsbyggnad och naturresurser, Luleå tekniska universitet, Institutionen för samhällsbyggnad och naturresurser |
| Source Sets | DiVA Archive at Upsalla University |
| Language | English |
| Detected Language | English |
| Type | Student thesis, info:eu-repo/semantics/bachelorThesis, text |
| Format | application/pdf |
| Rights | info:eu-repo/semantics/openAccess |
Page generated in 0.0017 seconds